Emerson SAPAG User manual

Pressure Seal Gate Valves -Style A-

Installation and Maintenance Instructions

Emerson reserves the right to change the contents without notice SAPLT-0028-EN-1308

Section 1 - Valve Storage

1.1 Preparation and Preservation for Shipment

All valves are properly packed in order to protect the parts that are subject to deterioration during

transportation and storage on site. In particular, the following precautions should be taken:

1. The valves must be packed with the wedge in the closed position.

2. The weld ends surface shall be protected with suitable protective like Deoxaluminite. The end

shall be closed with plywood or plastic disc fixed at the edge by strips.

3. All actuated valves must be carefully securely palleted or crated, in order to ensure that the

parts of actuator (especially pneumatic piping or accessories) do not extend beyond the skid/

crate.

4. The type of packing must be defined in the Customer’s Order and shall be appropriate to ensure

safe transportation to final destination and eventual conservation before installation.

Cast Gate Valves Pressure Seal -Style A-

Wedge Gate and Parallel Slide Configuration

1.2 Handling Requirements

A - Packed Valves

Crates: Lifting and handling of the packed valves in crates will be carried out by a fork lift truck, by

means of the appropriate fork hitches.

Cases: The lifting of packed valves in cases should be carried out in the lifting points and at

the center of gravity position which have been marked. The transportation of all packed

material must be carried out safely and following the local safety regulations.

B - Unpacked Valves

1. The lifting and the handling of these valves has to be carried out by using appropriate means

and at respecting the carrying limits. The handling must be carried out on pallets, protecting the

machined surfaces to avoid any damage.

2. With valves of large dimensions, the sling and the hooking of the load must be carried out using

the appropriate tools (brackets, hook, fasteners, ropes) and load balancing tools in order to

prevent them from falling or moving during the lifting and handling.

Contents

1 Valve Storage 1

1.1 Preparation and Preservation for Shipment 1

1.2 Handling Requirements 1

1.3 Storage and Preservation before Installation 2

2 Installation 2

2.1 Preparation before Installation 2

2.2 Installation Instructions 3

2.3 Valve Verification before Start Up 3

2.4 Operations Instructions 3

Table I: Bolt Torque Figures for Packing Bolts 4

Table II: Bolt Torque to Ensure Tightness of Pressure Seal Gasket 4

2.5 Periodic Valve Verification during Service 4

Troubleshooting Guide 4

3 Maintenance 5

3.1 Packing Maintenance 5

3.2 Bonnet Gasket Replacement 5

4 Valve Removal 6

5 Greases and Special Tools 6

5.1 Greases 6

Table III: Grease and Lubricant List 6

5.2 Special Tools 6

SAPAG

www.valves.emerson.com

Pressure Seal Gate Valves -Style A-

Installation and Maintenance Instructions

Emerson reserves the right to change the contents without notice page 2

1.3 Storage and Preservation before Installation

In case the valves have to be stored before installation, the storage has to be carried out in a

controlled way, and has to be performed in accordance with the following criteria:

1. The valves have to be stocked in a closed, clean and dry storage room.

2. The wedge must be in the closed position, and the end faces must be protected with plastic or

wooden discs fixed with straps. If possible, keep the original protection.

3. Periodical checks have to be carried out in the storage area to verify that the above mentioned

conditions are maintained.

For actuated valves, in addition to the above, please refer to the warnings in the manual of the

actuator.

Caution

For valve handling and/or lifting, the lifting equipment (fasteners, hooks, etc.) must be sized and

selected while taking into account the valve weight indicated in the packing list and/or delivery

note. Lifting and handling must be made only by qualified personnel.

Do not use the lifting points located on the actuator, if any, to lift the valve. These lifting points are

for the actuator only.

Caution must be taken during the handling to avoid that this equipment passes over the workers

or over any other place where a possible fall could cause damage. In any case, the local safety

regulations must be respected.

Section 2 - Installation

2.1 Preparation before Installation

1. Carefully remove the valve from the shipping package (box or pallet) avoiding any damage to

the valve or, in case of automated valves, to the electric or pneumatic/hydraulic actuator or

instrumentation.

2. Clean the inside of the valve using an air line. Ensure that there are no solid objects such as

pieces of wood, plastic or packing materials within the valve or on the valve seat.

3. Confirm that the materials of construction listed on the valve nameplates (service and

temperature) are appropriate for the service intended and are as specified.

4. Define the preferred mounting orientation with respect to the system pressure. If any (see arrow

on the body), identify the upstream side (high pressure) and downstream side (low pressure).

Note

Storage in an open area for a limited period can be considered only in case the valves have

appropriate packing (packed in cases lined with tarred paper, and contents well protected with

barrier sacks).

Do not place consignment packages directly on the ground.

Do not expose consignment packages to the weather or directly to the sun.

Check the packaging every two months.

Warning

Verify that the direction of the flow in the line corresponds to the arrow indicated on the valve

body. Valves without the arrow are bi-directional.

See the actuator user manual for the actuator preparation.

Valve slinging

Figure no. 1

Pressure Seal Gate Valves -Style A-

Installation and Maintenance Instructions

Emerson reserves the right to change the contents without notice page 3

2.2 Installation Instructions

Gate valves are normally installed in horizontal pipe with vertical stem.

These valves can also be installed in vertical or horizontal pipe with stem other than vertical, but

this may require special construction depending on valve size, service condition, material and type

of operator.

For a correct operation, Sapag recommends that the valve shall be installed and oriented following

the indications of fig. 2.

This can help minimize any problem associated with solid particles present in the fluid that

otherwise could deposit in the lower part of the body and be obstacle to the wedge complete

closure.

Unless otherwise recommended by Sapag, the valve should be installed with the wedge in the

closed position, to ensure that the seat ring in the wedge is not damaged during installation.

Particular care should be taken with those valves equipped with ‘fail-open’ actuators.

For operating temperatures above 200°C (392°F) thermal insulation of the valve body is

recommended.

Handling and lifting of the valves during installation MUST be performed following the same criteria

and instructions described in previous points “1.2 Handling Requirements” and “1.3 Storage and

Preservation before Installation”.

Important

After the valves installation and before the line testing, it is recommended to perform an

accurate cleaning of the lines to eliminate dirt and any foreign objects that could seriously

jeopardize the tightness between seat/disc and the correct operation of the valve.

Buttweld Valves

Position the valve and check the alignment with the pipe, then proceed with welding, in

accordance with the applicable welding procedure.

Important

If piping system is pressurized with water for testing, and in case the piping system has been

shut down after testing for a long time, the following recommendations should be adopted.

a. Use corrosion inhibitor with water to pressurize the piping system

b. After testing, the piping system should be depressurized and the test water completely

drained.

2.3 Valve Verification before Start Up

1. Tighten the packing just enough to prevent stem leakage. Over-tightening will decrease packing

life and increase operating torque. The bolt torque figures for the packing bolts can be calculated

as indicated in Table I.

2. Check the operation of the valve by stroking it to “full open” and “full close”.

3. If the valve has been stored for a long time, check the bolt torque for bolting (pos. 31) in

accordance with table II.

2.4 Operations Instructions

1. Style A Series Gate Valves do not require special care to work properly.

The following instructions will help provide a satisfactory and long life service.

2. Make sure to perform periodic valve verification as described in paragraph 2.5.

3. In case of actuated valves always follow the specific instructions given by the actuator’s

manufacturer.

4. Never change the setting of torque and/or limit switches which have been carefully set during

the final test at Sapag workshop.

Figure no. 2

Installation positions

recommended

90° max.

3/8 18 24,5

1/2 37 50

5/8 74 100

3/4 125 170

7/8 207 280

1 310 420

1 1/8 443 600

1 1/4 627 850

1 3/8 811 1100

Pressure Seal Gate Valves -Style A-

Installation and Maintenance Instructions

Emerson reserves the right to change the contents without notice page 4

2.5 Periodic Valve Verification during Service

A - Normal Check

1. Verify monthly that there is no leakage from packing or in the body/bonnet area. If the leakage

has been detected from the packing, tighten nuts according to the procedure described in

Section 3.

If the leakage does not stop, follow the procedure for packing maintenance (3.1).

If the leakage has been detected from the body/bonnet, tighten the nuts (pos. 31) as indicated in

Table II.

If the leakage does not stop, follow the maintenance procedure for the replacement of the body/

bonnet gasket (3.2, 3.3).

2. Every 2 / 3 months, depending on operating frequency, verify the greasing of bearings and stem

thread.

3. For actuated valves, in addition to the above, please refer also to the warnings in the actuator

manual.

Troubleshooting Guide

Symptom

Stem packing leaking

Body-Bonnet leaking

Valve leaking

Jerky operation

Back seat leaking

Table I: Bolt Torque Figures for Packing Bolts

For System pressures < 2533 psi For System pressures ≥ 2533 psi

Torque (ft lbs) = (24.87) x (OD2 _ ID2) x (d) Torque (ft lbs) = (S.P./101.8) x (OD2 _ ID2) x (d)

Torque (Nm) = multiply Torque (ft lbs) x 1.3558

Where: OD = Stuffing Box Bore (ln.)

ID = Stem Diam (In.)

d = Gland Stud Diam (in.)

S.P. = System Pressure (psi)

This “Torque method” may result in more or less than 30% compression.

Important

To ensure tightness of Pressure Seal gasket,

pull up bolts must be tightened when valve is

under fully hydrostatic test pressure.

B - Preventive Actions

1. Every 3 months verify the tightness of gland bolts.

2. Every 6 months on motorized valves and every 8 months on hand operated valves, grease stem

and bearings.

3. Every 12 months check the travel of the gland follower, setting a new packing when the end of

the travel is approaching.

4. Every 4 years disassemble the critical service valves and/or actuated valves, verifying the sealing

surfaces and lap them again when necessary. Substitute the bonnet gasket and the packing,

grease the stem.

5. For the actuator, proceed as indicated in its maintenance manual.

Table II:

Bolt Torque to Ensure Tightness

of Pressure Seal Gasket

Position 31 for Gate Valves

Stud Torque ft.lbs. Torque Nm

Possible Cause

1. Gland flange nuts too loose

2. Packing damaged

1. Gasket bolting loose

(pos 31)

2. Gasket damage

1. Valve not fully closed

2. Debris trapped in valve

3. Sealing surface damaged

1. Packing is too tight

2. Air supply inadequate

(forpneumatic act.)

1. Back seat damage

Solution

1. Tighten gland flange nuts.

2. Replace packing

(SeeParagraph3.1)

1. Tighten bolting

(pos 31)

2. Replace the gasket

1. Close valve

2. Cycle and flush (with valve open)

to remove debris

3. Recondition the seat surface

1. Loosen gland nuts, cycle the

valve, retighten

2. Increase air supply pressure

1. Replace the back seat

Pressure Seal Gate Valves -Style A-

Installation and Maintenance Instructions

Emerson reserves the right to change the contents without notice page 5

Section 3 - Maintenance

The Style A Series Valves have been designed to require minimum maintenance.

This manual describes on site repairs as:

- Packing Replacement

- Body/Bonnet Gasket Replacement

All the other repairs should be performed by Sapag or Nominated Service Company.

3.1. Packing Maintenance

If leakage is observed through the packing, tighten the gland nuts slowly and evenly until the

leakage stops.

1. Open completely the valve up to the backseat position.

2. Remove the nuts (16) of the gland bolts (15)

3. Lift the gland flange (10) and the gland (9)

4. Remove the worm-out packing using a hooking wire

5. For a better tightness, proceed to an accurate cleaning of the stem and stuffing box and make

sure there are no scratches or signs of seizing

6. The repacking shall be carried out by placing one ring at a time around the stem, inside the

stuffing box and by making sure that they are correctly oriented. Press it into the bottom (refer

to Figure no. 3).

7. When the stuffing box is filled, replace the gland (9) and gland flange (10) in their original

position.

8. Tighten gland nuts in accordance with Table I (Bolt Torque figures for Packing Bolts).

9. Cycle the valve.

10. Pressurize the line.

11. If a leakage is detected, tighten the gland nuts slowly and evenly until the leakage stops.

3.2 Bonnet Gasket Replacement

1 = Braided graphite

2 = Die formet graphite (5 or 6 ring)

3 = Metal ring

Figure no. 3

Figure no. 4

Caution

Do not over-tighten packing gland nuts. Over-tightening will increase the torque required to

operate the valve.

When tightening the gland nut, use half-turn increments until leakage has stopped.

Warning

Before starting any maintenance, depressurize, drain and vent the line; check that the valves

are not in temperature; disconnect any electrical power supply.

Failure to do so may cause serious personal injury and/or equipment damage.

Warning

Before starting any maintenance, depressurize, drain and vent the line; check that the valves

are not in temperature; disconnect any electrical power supply.

Failure to do so may cause serious personal injury and/or equipment damage.

Please refer to Figure no. 4.

To replace the packing proceed as follows:

Pressure Seal Gate Valves -Style A-

Installation and Maintenance Instructions

Emerson reserves the right to change the contents without notice page 6

Section 4 - Valve Removal

If the valve needs to be removed from the line for some extraordinary reason, the user should

ensure the following:

1. The valve is depressurized, drained and vent.

2. The pipe shall be cut as far away from the valve as possible.

Section 5 - Greases and Special Tools

5.1 Greases

To lubricate the bearings on manual and gearbox operated valves, we suggest to use the grease

AGIP GRMUEP2 or an equivalent product, as showed in the following table:

Table III: Grease and Lubricant List

Manufacturer Grease

AGIP GRMUEP2

API PGX2

BP GREASE LTX2

ESSO BEACON 2

FINA FINAGREASE HP FINAGREASE EPL2

MOBIL MOBILUX EP2

Q8 REMBRANDT EP2

SHELL ALVANIA R2 SUPERGREASE A

TEXACO MULTIFAK EP2 GREASE L2

TOTAL MULTIS EP2 MULTIS 2

VISCOL SIGNAL ROLSFER 2

STATOIL UHIWAYLI LI G2

5.2 Special Tools

No special tool required for the Maintenance Operation described in this Manual.

Lifting lugs

for DN = 6”

For DN = 4” For DN = 3”

Please refer to Figure no. 5.

1. Unscrew the body bonnet nuts (pos.12) and the gland nuts (pos.16)

2. Lift up the yoke (pos.24) operating by the handwheel or gearbox handwheel

3. When the stem nut is free from the stem threads, lift up the yoke.

4. Unscrew the nuts (pos.31).

5. Remove the retaining ring (pos.311).

6. Remove the segment rings, push them out from the body groove by using the body holes

placed radially on the top of the body.

7. Lift up the bonnet (pos.6) and pressure seal body gasket (pos.5). Make sure not to damage the

packing. We suggest to replace the packing when changing the body gasket.

8. Carefully clean all the gasket housing and lubricate with suitable grease.

9. Replace the body gasket.

10. Reassemble all parts following backwards the above mentioned steps.

Caution

The nuts (pos.31) need to be retightened

after valve first pressurization, as indicated

in Table II.

Fig. no. 5

For the lubrication of the stem thread, use the grease SIGNAL CEP 30 produced by Viscol. As an

alternative you can utilize:

- CEPLATTYN 300 produced by REINER-FUCHS

- GRAFLOSCON produced by KLUBER

You can also use a grease having more than 25% pure graphite content (carbon 98%) granulometry

5m, without any abrasive agent.

For the lubrication of the actuator, refer to the relevant manual.

Table of contents

Other Emerson Control Unit manuals

Emerson

Emerson Fisher ACE95 Series User manual

Emerson

Emerson ENARDO 860 Series User manual

Emerson

Emerson Fisher Large ET User manual

Emerson

Emerson PACSystems VersaMax IC200BEM002 User manual

Emerson

Emerson FM-3 User manual

Emerson

Emerson Anderson Greenwood 727 Series User manual

Emerson

Emerson Fisher VS100 Series User manual

Emerson

Emerson Fisher TBX User manual

Emerson

Emerson Fisher Operating and maintenance manual

Emerson

Emerson SEMPELL Quick guide

Emerson

Emerson Daniel 700 Series User manual

Emerson

Emerson Fisher V250 User manual

Emerson

Emerson YARWAY 9100 ARC Series Manual

Emerson

Emerson Tescom ER5K User manual

Emerson

Emerson ANDERSON GREENWOOD MARVAC 121 Series User manual

Emerson

Emerson Baumann 83000 User manual

Emerson

Emerson Fisher Type H800 User manual

Emerson

Emerson Fisher 92C User manual

Emerson

Emerson BM6X Series User manual

Emerson

Emerson Coils ASC3 Series User manual

Emerson

Emerson Fisher Vonk CHV User manual

Emerson

Emerson Fisher Vee-Ball V150 User manual

Emerson

Emerson VA001-102-01 Guide

Emerson

Emerson White Rodgers 36C53 Series User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual