Emerson Bettis Om3-SCE300 User manual

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0

May 2022

Bettis OM3 - SCE300

Local Interface Module

May 2022

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0

Notes

This page intentionally left blank

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0

Table of Contents

May 2022

Table of Contents

Section 1: Optional Module 3: Local Interface Module

1.1 Local Interface Functionality ......................................................................... 1

1.2 Manufacturer................................................................................................ 2

Section 2: Assembling Procedure

Assembling Procedure ............................................................................................ 3

Section 3: Description Of OM3 Local Interface

3.1 Local Operator Interface................................................................................ 7

3.2 Description of the Local Interface.................................................................. 8

3.2.1 2-position selector ............................................................................. 8

3.2.2 LEDs indicating the position of the SCE300 actuator........................... 8

3.2.3 OPEN/CLOSE pushbuttons.................................................................. 8

Section 4: To Locally Operate the Actuator

To Locally Operate the Actuator .............................................................................. 9

Section 5: OM3 Wiring Diagram

OM3 Wiring Diagram............................................................................................ 10

Section 6: Identication

6.1 Water-, Dust-Proof Version.......................................................................... 11

6.2 Label for Application In Water-, Dust-Proof Areas............................................ 11

6.3 Explosion-Proof Version .............................................................................. 12

6.4 ATEX Label for Application in Hazardous Areas ............................................ 12

Section 7: Safety Instructions

7.1 Foreword .................................................................................................... 13

7.2 General Safety Instructions ......................................................................... 13

7.3 Check for Right Application......................................................................... 13

7.4 Applicable Standards and Regulations......................................................... 14

7.5 Terms and Conditions ................................................................................. 14

7.6 Manufacturer’s Liability............................................................................... 14

Section 8: Installation

8.1 Working Conditions .................................................................................... 15

8.2 Electrical Connections................................................................................. 15

8.3 Instructions for the Intrinsically-Safe Enclosures.......................................... 15

8.4 Installation in Ambient with Explosive Dusts................................................ 15

Section 9: Special Maintenance

9.1 Periodic Inspections .................................................................................... 16

9.2 Repairs of Intrinsically-Safe Parts ................................................................. 16

May 2022

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0

Notes

This page intentionally left blank

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0 May 2022

Optional Module 3: Local Interface Module

Section 1: Optional Module 3: Local Interface Module

Section 1: Optional Module 3: Local

Interface Module

1.1 Local Interface Functionality

The OM3 Local Interface module is supplied as an option on Bettis SCE300 actuators and

ts all models. It is possible to receive the actuator already equipped with the OM3 if

ordered together with the basic version. Alternatively, only for the water proof version,

it is possible to order the OM3 as a separate kit to be installed afterwards on the basic

actuator. The subsequent retrotting of the OM3 on existing SCE300 is not allowed in the

explosion-proof version. The OM3 is an optional module allowing local control with the

following additional functionalities:

• Selection of Local/Remote actuator control through the selector (lockable in

both positions).

• Open/Close command through the non intrusive pushbuttons.

• Actuator position indication by means of 2 LEDs.

NOTE:

For decommissioning instructions, please refer to the relevant section in

Installation, Operation and Maintenance Manual for Bettis SCE300 electric actuator.

!WARNING

SCE300 actuator must be electrically isolated before any disassembling and reassembling

operations. Before any disassembling or reassembling operations, please follow in detail the

relevant paragraph of the basic installation and operating manual (latest revision available).

!WARNING

The electronic parts of the SCE300 actuators and all optional modules can be damaged

by a discharge of static electricity. Before you start, touch a grounded metal surface to

discharge any static electricity.

NOTE:

The present IOM has to be considered integral part of the IOM for the basic

Installation, Operation and Maintenance Manual for Bettis SCE300 electric actuator.

May 2022

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0

2Optional Module 3: Local Interface Module

Section 1: Optional Module 3: Local Interface Module

!WARNING

SCE300 actuators can be operated through a Bluetooth™ PDA or PC with the

following conguration:

• The commands are enabled by Bluetooth, only when the BT control is active. When

operating with Bluetooth™, the controls via PDA or PC have priority on any other

remote commands and allow full actuator operability from a distance also when

the valve is not visible. Special attention must be paid under this condition to avoid

any damages or injuries to people working close to the valve. Bettis will not

accept any responsibility for damages or injuries caused by an improper use of your

Bluetooth™ PDA or PC.

!WARNING

It is assumed that the installation, conguration, commissioning, maintenance and repair

works are carried out by qualied personnel and checked by responsible specialists.

!WARNING

Repair work, other than operations outlined in this manual, is strictly reserved to qualied

Emerson personnel or to personnel authorized by the company itself.

1.2 Manufacturer

Manufacturer with respect to Machinery Directive 2006/42/EC: Emerson as specied on

the actuator label.

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0 May 2022

Assembling Procedure

Section 2: Assembling Procedure

To assemble the OM3 Local Interface module onto the SCE300 actuator, proceed as follows:

• Ensure that all the parts received with the OM3 are available, see Figure 1:

Figure 1 OM3 kit for SCE300 actuator

Pos. Q.ty Description

1 1 Local Interface module

2 4 Screws for connecting connector

Table 1.

• Gather the right tools for the assembly: a 5 mm Allen key and a screwdriver as

shown in Figure 2.

Figure 2 Tools for installing OM3 kit

May 2022

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0

4Assembling Procedure

Section 2: Assembling Procedure

• With the Allen key loosen the 4 cover screws and remove the terminal board

enclosure cover, see Figures 3. You will see the terminal board inside the actuator.

Remove the ground cable from the cover in the enclosure. The position of the

connections is shown on the yellow label that you will nd inside the cover just

removed, see Figure 4.

Figure 3 Removing terminal board enclosure cover

Figure 4 Electrical connections

!WARNING

Pay attention not to damage the joint surfaces of the cover/enclosurer.

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0 May 2022

Assembling Procedure

Section 2: Assembling Procedure

• Connect the Local Interface module to the ground stud by screwing the

‘ground kit’ (screw + toothed washer).

Figure 5 Grounding the Local Interface

• Take the 4 screws for connecting the Local Interface black connector to the

terminal board, in pos. 28-29-30-31 (see Figure 6 and wiring diagram) and

connect it with the screwdriver shown in Figure 7.

Figure 6 Position of the Local Interface connector on the terminal board

Figure 7 Connecting the Local Interface connector

May 2022

Installation, Operation and Maintenance Manual

VCIOM-17109-EN Rev. 0

6Assembling Procedure

Section 2: Assembling Procedure

• Now the Local Interface is connected to the actuator, see Figure 8.

• Take the 4 screws removed from terminal board cover and use them to x the Local

Interface to the actuator, using the 5 mm Allen key, see Figure 9.

Figure 8 OM3 kit connected to the SCE300 terminal board

Figure 9 Fixing the local interface onto the SCE300 actuator

NOTE:

Please note that the design of the Local Interface black connector has been engineered to

allow the installation in one way only. Due to the special design, it is not possible to reverse

the connection of the 4 cables to the terminal board and it is not possible to make a wrong

connection of the connector.

• The installation of the OM3 Local Interface module onto the SCE300 actuator is

now complete.

screws

Table of contents

Other Emerson Control Unit manuals

Emerson

Emerson FISHER NotchFlo DST User manual

Emerson

Emerson Crosby J Series User manual

Emerson

Emerson Mobrey MCU900 Series Installation instructions

Emerson

Emerson Keystone Figure 969 Hopper User manual

Emerson

Emerson Enardo ES-850 Series User manual

Emerson

Emerson TX7 User manual

Emerson

Emerson ENARDO 860 Series User manual

Emerson

Emerson Fisher Vee-Ball V200U Series User manual

Emerson

Emerson Liebert OpenComms SL-19534 User manual

Emerson

Emerson Anderson Greenwood 9300 Series User manual

Emerson

Emerson Coils ASC3 Series User manual

Emerson

Emerson CROSBY Guide

Emerson

Emerson ES-805 Series User manual

Emerson

Emerson Fisher Z500 User manual

Emerson

Emerson Daniel 762 User manual

Emerson

Emerson EX4-6-...FLR Series User manual

Emerson

Emerson Dixell XEV20D User manual

Emerson

Emerson Fisher Vonk CHV User manual

Emerson

Emerson 91 User manual

Emerson

Emerson OSE Series User manual

Emerson

Emerson Bettis XTE3000 User manual

Emerson

Emerson KTM Series Quick guide

Emerson

Emerson VS-FL Series User manual

Emerson

Emerson PACSystems RX3i IEC 61850 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual