Emerald EP-RANG-10 User manual

SMOKE ALARM USER MANUAL

DESCRIPTION

The unit is a photoelectric smoke alarm device. It is particularly sensitive for detecting visible

micro-particles (associated with smoldering ﬁres) and reacts faster than ionization alarms.

An example of such smoldering ﬁres is a cigarette burning in a couch or bedding, a common cause

of devastating blazes.

Please note this device does not detect ﬂames, heat, carbon monoxide or other hazardous gases.

It has many advanced features and an extended operational life with the included battery.

MODEL NUMBER: EP-RANG-10

Thank you for choosing Emerald Alarms.

This leaﬂet contains important information on the correct

installation and operation of your smoke alarm.

Please read all the information before commencing

installation and retain for future reference.

This unit has been designed to meet the latest

safety standards demanded in Australia and

complies with the requirements of AS3786:2014.

POWER: built-in DC3V (CR123A) 10 years Lithium battery

(non-replaceable battery)

OPERATION CURRENT: <5uA (standby) <60mA (alarm)

BATTERY LIFETIME: 10 years

ALARM VOLUME: 85dB (A) at 3 meters

ALARM SENSITIVITY: 0.1-0.16dB/m

HUSH/SILENCE TIME: approx. 8 minutes

COMPLY WITH: AS3786: 2014

SOUND PATTERN: ISO8201 (Bl 0.5s - pause 0.5s - Bl 0.5s - pause 0.5s - Bl 0.5s - pause 1.5s,

with the red LED ﬂash, repeat this alarm pattern

ALARM SOUND PATTERN:

Bl - Bl - pause 0.5s, Bl - Bl - pause 0.5s, Bl - Bl - pause 1.5s,

without the red LED ﬂash, repeat this alarm pattern

LOCATION OF SMOKE ALARMS

For maximum protection smoke alarms should be installed in

every room (except areas described in the previous section

‘Locations to Avoid’) to ensure people in the home will be able to hear

and respond to the alarm. At the very least install one smoke alarm on

every ﬂoor.

If you suspect a household member may not hear this smoke alarm

i.e. outdoor or indoor noise, sound sleepers, drug or alcohol usage,

the hard of hearing, etc install and maintain a specialty smoke alarm

device.

NOTE: In Australia each state has a dierent legislation when it comes

to smoke alarms. Please visit the relevant authority in your state for

speciﬁc legislation requirements.

ASSEMBLY AND ACTIVATION

Assemble and secure the smoke alarm to the ceiling using the

supplied screws and mounting plate.

NOTE: Optional magnetic assembly system with secure 3M self

adhesive mounts are available.

Press test button and hold it for 3 seconds until LED lights, and release

it within 2 seconds, the unit will generate a ‘beep’ indicates the alarm

working.

Warning: This smoke alarm is not suitable for wall (vertical)

mounting.

LOCATIONS TO AVOID

1. Don’t place alarms in bathrooms, kitchens, garages or

other rooms where the Alarm may be triggered by steam,

condensation and normal smoke/heat from appliances.

2. In areas with high humidity, like bathrooms or areas near

dishwashers or washing machines, install at least 3m away from

these areas.

3. Near air returns or heating and cooling supply vents, install

at least 1m away from these areas. The air could blow smoke away

from the detector, interrupting its alarm.

4. In rooms where the temperature may fall below 0°C or rise above

40°C (due to nuisance/false alarm activation).

5. In extremely dusty, dirty, or insect infested areas where

particles may interfere/obstruct with Alarm operation.

6. Away from air conditioning or ventilation grilles/louvers.

Smoke alarm

Screws

Rotate tighten Rotate remove

Ceiling Install hole

82.8+0.15cm

TYPICAL MULTISTORY OR SPLIT LEVEL HOME

For maximum protection, a smoke alarm should be installed on the

ceiling of each bedroom, living area, and hallway. Where a hallway

is more than 10 meters long install a smoke alarm at each end. Also

install a smoke alarm above each staircase.

For minimum protection, a smoke alarm should be installed above

each staircase, including the basement.

POSITION OF SMOKE ALARMS

Smoke will spread horizontally after rising to the ceiling so it’s

advisable to install the smoke alarm in the centre of the ceiling where

possible. Avoid areas where there is no circulation.

• When mounting an alarm on the ceiling, locate it a minimum of

30cm from the side wall.

• Install smoke alarm/s on slopped, peaked or cathedral ceilings

between 50cm and 250cm from the highest point of the ceiling.

TYPICAL SINGLESTORY HOME

For maximum protection, a smoke alarm should be installed on the

ceiling of each bedroom, living area, and hallway. Where a hallway is

more than 10 meters long install a smoke alarm at each end. If there

is a basement install a smoke alarm on the basement ceiling at the

bottom of the stairwell.

Additionally, a smoke alarm should be installed in the hallway

between the living areas (incl. kitchen) and bedrooms. Place it as near

to the living areas as possible and ensure the smoke alarm is audible

when bedrooms are occupied.

LIVING ROOM

BATH

KITCHEN

BEDROOM

BEDROOM BEDROOM

FAMILY ROOM

BEDROOM BEDROOM

KITCHEN

DINING

ROOM

LIVING

ROOM

BATH

Smoke alarm

for minimum protection

oSmoke alarm

for additional protection

Smoke alarm

for minimum protection

oSmoke alarm

for additional protection

OPERATION AND TESTING

Smoke alarms are an important safety device in the home. It is import-

ant to check them regularly to ensure they are operating correctly.

Regular Mode

When there is no smoke present, the red LED should ﬂash every

48 seconds indicating the alarm is operating correctly.

Alarm Mode

When the alarm detects smoke, the red LED will ﬂash once per

second and the alarm will sound loudly. The ﬂashing LED and alarm

will continue until the air is cleared.

Fault Mode

The alarm will generate a ‘chirp’ every 48 seconds indicating a fault.

TESTING YOUR SMOKE ALARM

It is recommended that you test your smoke alarm once a week to

ensure the smoke alarm is working correctly. Test by pushing the

test button on the cover. The alarm will sound if the alarm electronic

circuitry and battery are working. If no alarm sounds, the smoke alarm

has a defective battery, or another fault.

Warning: Do not use an open ﬂame to test your alarm.

You could damage the alarm or ignite combustible

materials and start a structure ﬁre.

LOW BATTERY POWER

Should your smoke alarm have a low battery the unit will emit an

audible ‘chirp’ once every 48 seconds and the red LED light ﬂashes

once at the same time. When this occurs you must replace the alarm

immediately. Your smoke alarm will continue to warn of this low battery

for at least 30 days. However, failure to change the alarm after this time

would mean your smoke alarm may have insucient power to alert

you in a real ﬁre situation.

NOTE: The battery in this unit is intended to last 10 years and cannot

be replaced.

Warning: Your smoke alarm requires the battery to have

sucient capacity of power to operate correctly.

SILENCE ALARM

If your smoke alarm emits the full alarm signal and you are not

testing the unit, the smoke alarm is warning you of a potentially

dangerous situation that requires your immediate attention. Only use

the alarm silence function after making sure that there is no ongoing ﬁre

emergency situation.

Do not block the vents on the alarm or disable the smoke alarm in

any way as this will remove your protection.

Smoke alarms can sometimes react to cooking fumes or other non

emergency situations. In the event of a known false alarm your smoke

alarm can be temporarily silenced by pressing the test button. Your

alarm will automatically return to full sensitivity within 8 minutes.

1. Press and release the silence button, the alarm sound will stop.

2. Your alarm will silence and enter into a reduced sensitivity

reset cycle for approximately 8 minutes.

3. During the reduced sensitivity reset cycle, the red LED will ﬂash

every 8 seconds indicating it is running in silent mode.

4. Your alarm will automatically return to full sensitivity on

completion of the reset cycle and the red LED will revert to ﬂashing

once every 48 seconds.

Warning: Never ignore any alarm. Ignoring the alarm may result

in injury or death. If your smoke alarm activates and you are not

absolutely certain of the source of the smoke, get everyone out

of the house immediately.

ROUTINE MAINTENANCE

Like other electrical accessories in the home, smoke alarms

require maintenance to ensure ecient and eective operation.

Proper maintenance can also reduce the likelihood of false alarms.

1. In addition to weekly testing, the alarm requires cleaning at least

once a month to remove dust, dirt, or debris.

2. Using a vacuum cleaner with the soft brush vacuum all sides and

cover of smoke alarm device.

NOTE: Do not attempt to remove the cover to clean inside. This will

aect warranty.

Warning:

1. Photoelectric smoke detectors can reduce the likelihood of a

disaster, but they cannot guarantee a 100% safety.

2. To ensure your maximum security, please install all smoke

detectors exactly according to this manual.

3. Keep the detectors clean. Do not allow dust to accumulate and

test them at least once a week.

4. If they are not working properly replace them immediately.

HOW TO DEACTIVATE THE SMOKE ALARM

Press the test button six times within three seconds, the

smoke alarm will chirp once indicating the product has been

deactivated. There will be no alarm functions while in this

status. You must reactivate the alarm before use. Please refer to

“ASSEMBLY AND ACTIVATION” to activate the product.

Warning: Deactivating this alarm should only be performed if

you need to dispose of the smoke alarm or if you need to cease

a nuisance alarm which is caused by a failure of the smoke

alarm.

WARRANTY INFORMATION

Emerald Alarms Pty Ltd warrants this smoke alarm to the original purchaser.

Emerald Alarms Pty Ltd warrants each new smoke alarm is free from defects in material and workmanship under normal use

and service for a period of 7 years from the date of purchase.

This warranty does not cover damage resulting from accident, misuse or abuse or lack of reasonable care of the product.

In no case shall Emerald Alarms Pty Ltd be liable for any incidental or consequential damages for breach of this or any other

warranty express or implied whatsoever. Faulty product can be mailed to the following address with a detailed explanation

of problem.

Emerald Alarms Pty Ltd

ABN 50 632 601 453

2/29 Mitchell Rd Brookvale NSW 2100 2021.10

Other Emerald Smoke Alarm manuals

Emerald

Emerald EP-VC-240-1 User manual

Popular Smoke Alarm manuals by other brands

x-sense

x-sense SD19-W user manual

BRK electronic

BRK electronic First Alert P1010 quick start guide

FireAngel

FireAngel Thermoptek ST-622 user manual

teko

teko Astra-42A user guide

Safetec

Safetec SDS-2/6 Additional Fault Finding Instructions

Siemens

Siemens PE-11C installation instructions

System Sensor

System Sensor DH500ACDC Installation and maintenance instructions

Resolution Products

Resolution Products RE612 CryptiX quick start guide

First Alert

First Alert PC900V user manual

Eminent

Eminent EM6590 E-Domotica user manual

Ei Electronics

Ei Electronics Ei Ei168RC user manual

Carrier

Carrier Kidde Quell Q301 user manual

VESDA

VESDA VLF-500 Product guide

ELRO

ELRO FS8110 instruction manual

Heiman

Heiman SMOKI NS-626PHS user manual

Regin

Regin SDD-S65 instruction manual

Family Gard

Family Gard FG225 user manual

Greystone

Greystone DSD120 Installation and maintenance instructions