Electrolux Washing machine User manual

SSD-P APdV, EB, HD 01/05 I599 34 71-47

SERVICE MANUAL

WASHING

Publication no.

599 34 71-47

ELECTROLUX-ZANUSSI S.p.A.

SPARE & SERVICE DOCUMENTATION

Corso Lino Zanussi,30

I - 33080 PORCIA /PN

ITALY

Fax +39 0434 394096

Edition: 2001.05.31

EN/eb

Diagnostics Guide to

EWM2000 Electronic

Control

WASHING MACHINES

WASHER DRYERS

Production: ZP Porcia (Italy)

SSD-P APdV, EB, HD 01/05 II 599 34 71-47

SSD-P APdV, EB, HD 01/05 III 599 34 71-47

CONTENTS

Aim of this manual .............................................................................................................. page IV

OPERATING PROCEDURE .............................................................................................. page IV

SUMMARY OF EWM2000 ELECTRONIC CONTROLS .................................................... page V

Table 1: FULL SMD VERSION with on/off button .............................................................. pages 1.1-1.2

Table 2: FULL SMD VERSION with on/off switch on the programme selector.................. pages 2.1-2.2

Table 3: DELTA3 & NEAT VERSION................................................................................. pages 3.1-3.2

Table 4: INPUT VERSION.................................................................................................. pages 4.1-4.2

Table 5: AEG VERSION (with on/off switch on the programme selector).......................... pages 5.1-5.2

DIAGNOSTIC CYCLES Phases......................................................................................... page 6.1

NO ACCESS TO DIAGNOSTICS PROGRAMME ............................................................. page 7.1

ALARM CODES.................................................................................................................. pages 8.1-8.35

HOW TO CHECK COMMUTATOR MOTORS ................................................................... page 9.1

CONFIGURATION CODE .................................................................................................. page 10.1

BASIC CIRCUIT DIAGRAM ............................................................................................... pages 11.1-11.3

MAIN ELECTRONIC BOARD CONNECTORS.................................................................. pages 12.1-12.3

BURNING MARKS ONMAIN ELECTRONIC BOARDS.................................................... pages 13.1-13.2

PICTURES LINKED TO FAULT FINDING ......................................................................... pages 14.1-14.10

SSD-P APdV, EB, HD 01/05 IV 599 34 71-47

INTRODUCTION

Aim of this manual

This manual aims to explain in a clear and simple way the phases a Service Engineer

should follow to solve problems highlighted by the different alarm codes in EWM2000

electronic appliances with electronic control.

Operating procedure

1. Find the type of control involved by checking the summaryat pageV.

2. Every user interface is connected with a summary table of the operations necessary to

read the possible alarms, to access the diagnostic cycle and to configurate the main

electronic board (see column “Diagnostic Table”).

3. Read the memorized alarm and consult the relative information (see “alarm codes”,

from page 8.1).

4. Delete memorized alarm.

5. If you cannot access the diagnostic cycle, consult chapter “No access to diagnostic

cycle” (page 7.1).

6. In case of replacement of main PCB check if there are burn marks (see page 13.1-

13.2)

7. After every replacing of the main electronic board, you need to configurate the module.

You can find further information about the configuration code at page10.1

(”configuration code”).

8. After every operation, check the functioning of the appliance through the diagnostic

cycle. For further information see page 6.1 (diagnostic cycle phases)

9. (Delete memorized alarm).

SUMMARY OF EWM2000 ELECTRONIC CONTROLS (ZP)

SSD-P APdV, EB, HD 01/05 V599 34 71-47

Type Styling Marks User interface Manuals (actual) Note Diagnostics table Examples of control panels

599 34 00-75; 599 33 70-05

599 34 05-08 Alarm Led 1

Alpha 2 Electrolux

A.Martin- Electrolux 599 34 20-83 Obstructed

filter Led 1

599 34 00-75; 599 33 70-05

599 34 05-08 Alarm Led 1

Ellipse

Privileg, Zoppas

Husqvarna,

Rosenlew, AEG,

Marynen, Hansa 599 34 20-83 Obstructed

filter Led 1

Multipanel

(Built-in)

Electrolux

Zanussi, AEG

Privileg

599 34 55-61

With

ON/OFF

button

FULL SMD

Sigma Zanker 599 34 37-91

Selector

with

ON/OFF 2

Delta 3 Zanussi, Rex 599 34 27-56 3

DELTA 3

Neat

(Jetsy-

IZ)

Zanussi, Rex, Aeg

Privileg, Electrolux,

Elektro-Helios

599 34 22-16 3

INPUT

Input

Rex

Zanussi

Privileg

599 34 22-87 4

599 34 15-14 Standard 5

AEG

Aeg Aeg

Privileg 599 34 39-45 Far East 5

BIG

SIZE

Multipanel

(first

version)

Zanker

Elektro-Helios 599 33 52-03 1

SSD-P APdV, EB, HD 01/05 VI 599 34 71-47

Table 1:FULL SMD with on/off button version

(the programme selector can be on the right or on the left of the module)

SSD-P APdV, EB, HD 01/05 1.1 599 34 71-47

ACCESS TO THE

DIAGNOSTICS

To access the diagnostics system:

→switch off the appliance and turn the programme selector knob

to RESET

→press the START/PAUSE button together with one of the other

buttons and then, holding down both buttons, press the

ON/OFF button to switch on the appliance.

→hold both buttons down until the buzzer (if featured) sounds and

the LEDs begin to flash (about 4 seconds)

DIAGNOSTIC CYCLE

→Correct operation of all the components in the appliance can be

checked by turning the programme selector knob clockwise.

1. Operation of the user interface (step 0, page 6.1)

2. Water fill to wash compartment (step 1, page 6.1)

3. Water fill to pre-wash compartment (step 2, page 6.1)

4. Water fill to conditioner compartment (step 3, page 6.1)

5. Hot water fill or fill to bleach compartment (certain models only)

(step 4, page 6.1)

6. Heating and, in Jetsystem models, recirculation (step 5, page

6.1)

7. Check for leaks from tub (step 6, page 6.1)

8. Drain and spin, check for pressure switch congruency (step 7,

page 6.1)

9. Drying (washer/dryers only) (step 8, page 6.1)

ALARMS

To read the last alarm condition, after accessing the diagnostics

system:

→turn the programme selector knob two positions counter-

clockwise from the RESET position (23 o 11).

Cancelling the last alarm condition

→press START/PAUSE button and no. 6button at the same time

during the course of the diagnostic cycle (2÷9).

→The alarm is cancelled also when a new configuration is given to

the main PCB.

CONFIGURATION OF THE MAIN PCB

To access the machine configuration procedure, first enter the

diagnostics system, and then:

→turn the programme selector one position counter-clockwise; the

display window shows the code relative to the position of the

programme selector and, after two seconds, the code relative to

the first of the 16 digits of the configuration code (position 0).

→when one of the option buttons is pressed (with the exception of

the START/PAUSE button), all the digits which make up the

configuration code are displayed in sequence.

→press the START/PAUSE button to modify the configuration

code (digit by digit).

→when all 16 digits have been entered, check that the code is

correct, then memorize the code by pressing the

START/PAUSE button and one of the option buttons at the

same time; these buttons should be held down until the buzzer

(if featured) sounds.

EXITING THE

DIAGNOSTIC

→To exit the diagnostic cycle, switch the appliance off, on, and

then off again.

Table 1:FULL SMD with on/off button version

(the programme selector can be on the right or on the left of the module)

SSD-P APdV, EB, HD 01/05 1.2 599 34 71-47

Closure of selector contacts

(C6 = common)

PROGRAMME SELECTOR 24-position

selector knob

12-position

selector knob

(C1 not present) C1 C2 C3 C4 C5

Display

code

1 - Reset 1 - Reset ●●●● 1 E

22 ●●

0 6

3- ●● 1 4

43 ●● 0 C

5- ●●● 1 C

64 ●● 0 A

●0 1

●●

0 3

●●

0 9

10 5 ●●●

0 E

11 - ●●

1 2

12 - ●●●

0 b

13 - ●● 1 1

14 - ●● 1 8

15 6 ●●●

1 3

16 - ●●● 1 A

17 7 ●●● 1 9

18 8 ● ●●● 1 b

19 - ●● 0 5

20 9 ●● ● 1 6

21 - ●0 2

22 10 ●0 4

23 11 ●0 8

24 12 ●1 0

● closed contact

Table of button codes

BUTTONNo. 012345678

L5 ❍❍❍❍❍❍❍❍●

L6 ❍❍❍❍●●●●❍

L7 ❍❍● ●❍❍●●❍

LED

L8 ❍●❍●❍●❍●❍

❍LED off

●LED lit

BINARY CODES

The table below can be used to convert the binary code shown by the LEDs into the corresponding letter or

decimal number

0123456789101112131415

value AbCdEF

❍❍❍❍❍❍❍❍●●●●●●●●

❍❍❍❍●●●●❍❍❍❍●●●●

❍❍●●❍❍●●❍❍●●❍❍●●

❍●❍●❍●❍●❍●❍●❍●❍●

❍LED off

●LED lit

Table 2:FULL SMD version with on/off switch on the programme selector

(the programme selector can be on the right or on the left of the module)

SSD-P APdV, EB, HD 01/05 2.1 599 34 71-47

ACCESS TO THE

DIAGNOSTICS

To access the diagnostics system:

→switch off the appliance

→press the START/PAUSE button (8) together with one of the

other buttons and then, holding down both buttons, switch on

the appliance by turning the programme selector one position

clockwise.

→hold both buttons down until the buzzer (if featured) sounds and

the LEDs begin to flash (about 4 seconds).

DIAGNOSTIC CYCLE

→Correct operation of all the components in the appliance can be

checked by turning the programme selector knob clockwise.

2. Operation of the user interface (step 0, page 6.1)

3. Water fill to wash compartment (step 1, page 6.1)

4. Water fill to pre-wash compartment (step 2, page 6.1)

5. Water fill to conditioner compartment (step 3, page 6.1)

6. Hot water fill or fill to bleach compartment (certain models only)

(step 4, page 6.1)

7. Heating and, in Jetsystem models, recirculation (step 5, page

6.1)

8. Check for leaks from tub (step 6, page 6.1)

9. Drain and spin, check for pressure switch congruency (step 7,

page 6.1)

10. Drying (washer/dryers only) (step 8, page 6.1)

ALARMS

To read the last alarm condition, after accessing the diagnostics

system:

→turn the programme selector knob to the last position but one

(23 or 11).

To cancel the last memorised alarm condition:

→press START/PAUSE button (8) and no. 4 button at the same

time during one of the 8 phases of the diagnostic cycle and not

in the alarm or configuration reading positions.

→The alarm is cancelled also when a new configuration is given to

the main PCB.

CONFIGURATION OF THE MAIN PCB

To access the machine configuration procedure, first enter the

diagnostics system, and then:

→turn the programme selector clockwise to the last position (24

or 12); the code relative to the programme selector is displayed

and after 2 seconds the code relative to the first of the 16 digits

of the configuration code (position 0) is displayed

→when one of the option buttons is pressed (with the exception of

the START/PAUSE button), all the digits, which make up the

configuration code, are displayed in sequence.

→press the START/PAUSE button (8) to modify the configuration

code (digit by digit).

→when all 16 digits have been entered, check that the code is

correct, then memorize the code by pressing the

START/PAUSE button and one of the option buttons at the

same time; these buttons should be held down for at least 4

seconds (i.e. the buzzer sounds).

EXITING

→To exit the diagnostic cycle, switch the appliance off, on, and

then off again.

Table 2:FULL SMD version with on/off button on the programme selector

(the programme selector can be on the right or on the left of the module)

SSD-P APdV, EB, HD 01/05 2.2 599 34 71-47

Closure of selector contacts

(C6 = common)

PROGRAMME SELECTOR 24-position

selector knob

12-position

selector knob

(C1 not present) C1 C2 C3 C4 C5

Display

code

1 - Reset 1 - Reset ●●●● 1 E

22 ●●

0 6

3- ●● 1 4

43 ●● 0 C

5- ●●● 1 C

64 ●● 0 A

●0 1

●●

0 3

●●

0 9

10 5 ●●●

0 E

11 - ●●

1 2

12 - ●●●

0 b

13 - ●● 1 1

14 - ●● 1 8

15 6 ●●●

1 3

16 - ●●● 1 A

17 7 ●●● 1 9

18 8 ● ●●● 1 b

19 - ●● 0 5

20 9 ●● ● 1 6

21 - ●0 2

22 10 ●0 4

23 11 ●0 8

24 12 ●1 0

● closed contact

Table of button codes

BUTTONNo. 012345678

L20 ❍❍❍❍❍❍❍❍●

L21 ❍❍❍❍●●●●❍

L22 ❍❍●●❍❍● ●❍

LED

L23 ❍●❍●❍●❍●❍

❍LED off

●LED lit

BINARY CODES

The table below can be used to convert the binary code shown by the LEDs into the corresponding letter or

decimal number

0123456789101112131415

Value

AbCdEF

❍❍❍❍❍❍❍❍●●●●●●●●

❍❍❍❍●●●●❍❍❍❍●●●●

❍❍●●❍❍●●❍❍●●❍❍●●

❍●❍●❍●❍●❍●❍●❍●❍●

❍LED off

●LED lit

Other manuals for washing machine

This manual suits for next models

Table of contents

Other Electrolux Washer manuals

Electrolux

Electrolux EWF 1230 User manual

Electrolux

Electrolux EWS 31264 SU User manual

Electrolux

Electrolux EWF 106510 W User manual

Electrolux

Electrolux EW7F3R48SI User manual

Electrolux

Electrolux WE 170PP User manual

Electrolux

Electrolux Wave-Touch EWFLS70JIW0 User manual

Electrolux

Electrolux EWN 148640 W User manual

Electrolux

Electrolux EWF12853S User manual

Electrolux

Electrolux WAGL 2 T 200 User manual

Electrolux

Electrolux UFW 47 K 8161 User manual

Electrolux

Electrolux EWF 14260 User manual

Electrolux

Electrolux EWC 1350 User manual

Electrolux

Electrolux EWB 76210 W User manual

Electrolux

Electrolux EWF8024BDWA User manual

Electrolux

Electrolux EWM 1042 NDU User manual

Electrolux

Electrolux W5105H User manual

Electrolux

Electrolux EWT531 User manual

Electrolux

Electrolux IQ-TOUCH 137378100 A User manual

Electrolux

Electrolux WH1048 Instruction Manual

Electrolux

Electrolux EWF 106410 A User manual

Electrolux

Electrolux EWF10831 User manual

Electrolux

Electrolux EW2F3048R9 User manual

Electrolux

Electrolux EWF 87210 W User manual

Electrolux

Electrolux EOB63100X User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Beko

Beko WKB 51231 PTMA manual

Electrolux washing machine User manual

Popular Washer manuals by other brands