Electrolux WA SL3 M Instruction Manual

INSTALLATIONAND

MAINTENANCE

WASHING MACHINE 2-15

TUMBLE DRYER 16-34

INDEX 36

WA SL3 M

TK SL3 M

TA SL3 M

SAFETY 3

Transit screws

General

Child lock on Start/Stop button

Door

Overfill cut-out

Packaging

Transport/Winter storage

Scrapping

PARTS OF THE WASHING MACHINE 4

TECHNICAL INFORMATION 4–5

Technical data

Programme cycles

MECHANICAL INSTALLATION 6–8

Transit screws

Positioning the washing machine

Adjusting the feet

Connecting to water supply

Water intake – mixed or cold water

Connecting to drain

ELECTRICAL INSTALLATION 9

Electrical installation

Connecting to coin mechanism

CONTENTS – WASHING MACHINE

CHANGING SETTINGS 10–11

Language

Locking the programme

Wash temperature, C or F

Changing preset wash temperature

Child lock

MAINTENANCE 12–13

Emptying/cleaning trap and drain pump

Inspection holes under drum paddles

Cleaning the detergent drawer

Cleaning the outside of the machine

In areas with hard water

TROUBLESHOOTING 14–15

Door will not open

Machine will not start

Error messages

The display is lighting when a program

me is selected, but no characters or

digits are shown

Wrong language displayed

WASHING MACHINE CONTENTS

GENERAL

• Read and keep this manual!

• Any electrical work or plumbing must be car-

ried out by qualified tradesmen.

• Remove the transit screws before you use the

machine, see Mechanical installation.

CHILD LOCK ON BUTTON

To prevent accidental button pushes on the

button you can activate the child lock

function. The button then must be held

in for three seconds to activate the machine.

DOOR

The door is opened electrically, so it cannot be

opened until the machine is connected to the

electrical supply! The door can however be ope-

ned in an emergency, see Troubleshooting.

OVERFILL CUT-OUT

If the water level in the machine rises above

normal the overfill cut-out shuts off the water

intake and starts pumping out the water. The

programme resumes when the water level has

dropped.

PACKAGING

Recycle the packaging according to recommen-

dations in your area.

TRANSPORT/WINTER STORAGE

If you intend to transport the machine or store

it over winter in unheated premises, empty the

trap and the drain pump, see the chapter on

Maintenance.

Any questions? Call service.

SCRAPPING

At the end of its life the machine must be disa-

bled before being scrapped.

Contact your local recycling centre to find

out where to dispose of it or recycle it.

The machine has been built and marked to

facilitate recycling.

SAFETY

SAFETY WASHING MACHINE

TECHNICAL DATA

Height, Width, Depth: 850 mm, 595 mm, 585 mm.

Weight: 73 kg.

Drum capacity: 50 l.

Max wash load: 6.0 kg.

Spin speed: 1200 rpm.

Power rating and element power: See rating plate.

Water pressure: 0.1–1 MPa, 1–10 kp/cm2, 10–100 N/cm2.

Composition of drum and fluid container: Stainless steel.

Composition of casing: Powder-painted and hot-dip galvanized sheet steel

or stainless steel.

Installation: Static on four adjustable, rubber-covered feet.

Water supply: 1.5 m PEX hose.

Drain: 1.7 m polypropylene hose (pump) or 0.4 mm EPDM

rubber hose (valve).

This machine is approved for all UK applications as suitable for Category 5.

Product is listed in the WRAS regulations advisory scheme directory and is suitable for direct

connection to mains drinking water.

No special plumbing arangements e.g. break tanks are required.

1. DETERGENT DRAWER

2. POWER SWITCH

3. PROGRAMME PANEL

4. RATING PLATE

5. DOOR-DRAIN PUMP/EMERGENCY OPEN

6. DRAIN PUMP/EMERGENCY OPEN (BEHIND

FLAP)

7. DOOR

1. DETERGENT COMPARTMENT – PRE-WASH

2. DETERGENT COMPARTMENT – MAIN WASH

3. FABRIC CONDITIONER COMPARTMENT

PARTS OF THE WASHING MACHINE

TECHNICAL INFORMATION

WASHING MACHINE PARTS OF THE WASHING MACHINE/ TECHNICAL INFORMATION

1 2 3

TECHNICAL INFORMATION WASHING MACHINE

110

P1 Heavy wash 90°C

P2 Normal wash 60°C

P3 Light wash 60°C

P4 Normal wash 40°C

P5 Synthetic wash 40°C

P6 Super quick wash 40°C

P7 Wool/hand wash 30°C (1)

P8 Spin

(1) High water level and gentle motor action.

EURO

PROGRAMMES

Max .load

Pre wash

Rinse

Spin

Rinse

Spin

Rinse

Spin

Length (appr. min)

Main wash

P1 Heavy wash 90°C (2)

P2 Heavy wash 80°C (2)

P3 Normal wash 60°C

P4 Normal wash 40°C

P5 Synthetic wash 40°C

P6 Super Quick wash 40°C

P7 Wool/hand wash 30°C (1)

P8 Rinse

MEDICAL

PROGRAMMES

(1) High water level and gentle motor action. (2) Cannot be interrupted.

Max .load

Pre wash

Rinse

Spin

Rinse

Spin

Rinse

Spin

Length (appr. min)

Main wash

WASHING MACHINE MECHANICAL INSTALLATION

MECHANICAL INSTALLATION

TRANSIT SCREWS

Before the machine can be used the three trans-

it screws must be removed as described below.

Each transit screw has a washer and a rubber

spacer. The rubber

spacers are used to

protect the screw ho-

les after the screws

have been removed.

1. First unscrew the screw and remove the was-

her.

2. Then pull out the rubber spacer.

3. Finally, refit the rubber spacers to cover the

transit holes.

595 mm

585 mm

850 mm

min 600 mm

min 850 mm

POSITIONING THE WASHING MACHINE

The washing machine can be built-in or free-

standing. It should be positioned so that there

is an electrical socket within easy reach.

A. Built-in

The washing machine can be built in under a

worktop with a working height of 850–900 mm.

Leave a 5 mm gap around the machine. This

also applies between the rear edge of the top

the machine and the wall behind.

B. Free-standing

The washing machine can be placed alongside

or underneath the tumble dryer.

The machine can be anchored to the floor, see

enclosed bag containing instructions and parts.

ADJUSTING THE FEET

Adjust the feet so that the machine is level and

steady on the floor.

Tighten the lock-

ing nuts.

CONNECTING TO WATER SUPPLY

The machine should be connected to the water

supply by someone who has the necessary skill.

The machine is connected using the supplied

inlet hose.

NOTE!

It is important that you use the inlet hose that

is supplied, not an old hose.

The water pressure must be 0.1–1 MPa

(about 1–10 kp/cm2; 10–100 N/cm2).

The water supply pipe must be fitted with a

shut-off valve.

If the supply pipe has just been installed we

recommend that it is flushed out thoroughly

Locking nut

MECHANICAL INSTALLATION WASHING MACHINE

600-900 mm

first to remove any dirt. Otherwise this could

clog the intake filter in the machine and block

the water supply.

WATER INTAKE – MIXED OR COLD WATER

On delivery the machine is set to use mixed hot

and cold water. The machine can be reset to use

only cold water or hot water.

To change the water intake setting, do as

follows:

Switch off the power switch, , then switch

it on again so that the machine is in start-up

mode.

Press the

button five times, then press

the

button five times. You have to comple-

te these ten button presses within fifteen se-

conds.

Within three seconds of pressing the

but-

ton for the fifth time you must then select the

type of water intake you want by pressing the

buttons.

to use cold water only (C).

to use mixed hot and cold water (E).

A letter C near the bottom right of the dis-

play shows that cold water is being used and

the letter E indicates mixed hot and cold.

CONNECTING TO THE DRAIN

Machine with drain pump

The machine is supplied with a drain hose al-

ready fitted and this should be connected to a

laundry sink, or the like, at a height of 600–900

mm above the floor.

The lower height (600 mm) is always prefera-

ble. Make sure the drain hose is not kinked.

Machine with drain valve

An outlet hose is supplied with the machine.

This must be connected to the outlet on the

machine and

empty into a

floor drain

or gutter

drain.

NOTE!

The end of the outlet hose must be lower than

the lowest

point of the

outlet valve.

WASHING MACHINE MECHANICAL INSTALLATION

ELECTRICAL INSTALLATION

The washing machine must be connected using

a permanently installed cable through an isola-

ting switch by a qualified electrician.

Power supply

The machine is supplied, depending on market,

for one of the following supplies (see rating

plate):

A. 3-phase, 400V, 50 Hz supply, 10 A.

B. Single-phase, 230 V, 50 Hz supply, 13/16 A.

C. Single-phase, 230 V, 50 Hz supply, 10 A.

If an earth leakage circuit breaker is fitted it

must be of type A.

Reconfiguration

The machine can be reconfigured. The machi-

ne should be reconfigured as shown in the wi-

ring diagram underneath the top panel of the

machine.

NOTE!

Electrical connection /reconfiguring must be car-

ried out by a qualified electrician.

ELECTRICAL INSTALLATION WASHING MACHINE

CONNECTING TO A COIN MECHANISM

Connection to a coin mechanism must be car-

ried out by a qualified electrician.

A special connecting cable is required to con-

nect the machine to a coin mechanism. This

can be ordered as a spare part, art. no. 92 090

95.

Recommendations for choice of coin mechanism

The connecting cable (92 090 95) supplies the

coin mechanism with power (230 V). The coin

mechanism must be able to short-circuit two

signal leads for a period of time (around 0–10

minutes). This is so that the user has time to

load the laundry, select the programme and start

the programme after inserting the coins.

LANGUAGE

You can change the language of the displayed

text.

The languages you can choose from are Dansk,

Deutsch, English, Espanol, Français, Italiano,

Nederlands, Norsk, Portugués, Suomi and

Svenska.

To change language do as follows:

Switch off the power switch, , then switch it

on again so that the machine is in start-up mode.

Press the

button five times, then press

the

button five times. You have to comple-

te these ten button presses within fifteen se-

conds.

Within three seconds of pressing the

but-

ton for the fifth time you should then select the

language you want by pressing the

buttons.

LOCKING A PROGRAMME

If for some reason you want to limit the number

of programmes that can be used you can lock

one or more programmes.

No characters or digits are shown on the dis-

play when a locked programme is selected.

To lock or unlock a programme, do as follows:

Switch off the power switch, , then switch it

on again so that the machine is in start-up mode.

Press the

-button five times, then press

the

-button five times. You have to com-

plete these ten button presses within fifteen se-

conds.

Within three seconds of pressing the

CHANGING SETTINGS

button for the fifth time you should hold in the

programme button for the programme you want

to lock for 5-10 seconds until the information

in the display starts flashing.

Then you can lock the programme by relea-

sing the programme button and pressing the

-button once.

Do the same to unlock the programme.

WASH TEMPERATURE - CENTIGRADE OR FAHRENHEIT

You can change the way the temperature is dis-

played from centigrade (C) to Fahrenheit (F).

To change the temperature display, do as follows:

Switch off the power switch, , then switch it

on again so that the machine is in start-up mode.

Press the

button five times, then press

the

button five times. You have to comple-

te these ten button presses within fifteen se-

conds.

Within three seconds of pressing the

button for the fifth time you should then press

the

buttons to select centigrade

CHANGING PRESET WASH TEMPERATURE

You can change the preset wash temperatures

for each of the programmes. The temperatures

you can choose from are:

Heavy wash - C, 30, 35, …, 85, 90ºC.

Normal wash - C, 30, 35, …, 85, 90ºC.

Light wash - C, 30, 35, …, 85, 90ºC.

Synthetic wash - C, 30, 35, …, 85, 90ºC.

Super quick wash - C, 30, 35, …, 85, 90ºC.

Wool/hand wash - C, 30, 35, 40ºC.

WASHING MACHINE CHANGING SETTINGS

This manual suits for next models

Table of contents

Other Electrolux Washer manuals

Electrolux

Electrolux EWG 12450 W User manual

Electrolux

Electrolux EWF9023BDWA User manual

Electrolux

Electrolux TRICITY BENDIX AW 1054 W Product guide

Electrolux

Electrolux EWFH 12280 W User manual

Electrolux

Electrolux EWF 1498 CWW User manual

Electrolux

Electrolux LAVAMAT 74950 W User manual

Electrolux

Electrolux EW 1100 F Quick guide

Electrolux

Electrolux EWM1000 User manual

Electrolux

Electrolux EWT121 User manual

Electrolux

Electrolux EWF 1286 GDW User manual

Electrolux

Electrolux EWP 1464 TDW User manual

Electrolux

Electrolux WASL2E202 User manual

Electrolux

Electrolux EWS 31256 EDU User manual

Electrolux

Electrolux WH 810 User manual

Electrolux

Electrolux EWT 2266AOW User manual

Electrolux

Electrolux EWS 86110W User manual

Electrolux

Electrolux EWFLS70J RR User manual

Electrolux

Electrolux PW9 User manual

Electrolux

Electrolux EWF9025DQWB User manual

Electrolux

Electrolux EWS 105410 A User manual

Electrolux

Electrolux LAVALOGIC EWM 3000 User manual

Electrolux

Electrolux LI22Y User manual

Electrolux

Electrolux Zanussi F1045 W User manual

Electrolux

Electrolux EF7742OBI User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Beko

Beko WKB 51231 PTMA manual