Electrolux SATF7000FS0 User manual

Full Size Tumble Action Washers

Before beginning installation, carefully read these instructions. This will simpfify the

installation and ensure the washer is installed correctly and safely. Leave these instructions

near the washer after installation for future reference.

NOTE: The electrical service to the washer must conform with local codes and ordinances

and the latest edition of the National Electrical Code, ANS!/NFPA 70.

For your safety the information in

this manual must be followed to minimize the risk

of fire or explosion or to prevent property damage,

personal injury or loss of life.

- Do not store or use gasoline or other flammable

vapors and liquid in the vicinity of this or any

other appliance.

-WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch; do not

use any phone in your building.

•Clear the room, building or area of all

occupants.

•Immediately call your gas supplier from a

neighbor's phone. Follow the gas suppliers

instructions.

•If you cannot reach your gas supplier, call

the fire department.

Installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

Printed in U.S.A.

Contents

S UBJECT PAGE

Pre-lnstallation Requirements 2

Electrical Requirements 2

Grounding Requirements 2

Water Supply Requirements 2

Drain Requirements 2

Rough-In Dimensions 3

Location Of Your Washer 4

Unpacking 4-5

Installation B-6

Replacement Parts 6

WN 134965500(0708)

PRE-INSTALLAT!ON REQUIREMENTS

Tools Required for Installation:

I. Phillips screwdriver

2. 10 mm socketwith ratchet.

3. Channel-lock adjustable pliers.

4. Carpenter's level.

absence of local codes, with the National Electrical

Codes, ANSI/NFPA 70 (latest edition). If in doubt,

call a licensed electrician. DO NOTcut off or alter

the grounding prong on the power supply cord. In

situations where a two-slot receptacle is present,

it is the owner's responsibility to have a licensed

electrician replace it with a properly grounded

three prong grounding type receptacle.

ELECTRICAL REQUIREMENTS

CIRCUIT- Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2 wire, with ground, 120 volt, single

phase, 60 Hz, Alternating Current. NOTE: Because of

potential inconsistent voltage capabilities, the useof this

washer with power created by gas powered generators,

solar powered generators, wind powered generators or

any other generator other than the local utility company

isnot recommended.

OUTLET RECEPTACLE - Properly grounded 3-prong

receptacle to be located so the power supply cord is

accessible when the washer is in an installed position.

NOTE: GFI (Ground Fault Interrupter) receptacle is not

required.

GROUNDING REQUIREMENTS

Improper connection of the equipment

grounding conductor can result in a risk of electrical

shock. Check with a licensed electrician if you are in

doubt asto whether the appliance isproperly grounded.

.The washer MUST be grounded. In the event of

malfunction or breakdown, grounding will reduce

the risk of electrical shock by a path of least

resistance for electrical current.

.Sinceyour washer isequipped with a power supply

cord having an equipment-grounding conductor

and a grounding plug, the plug MUSTbe plugged

into an appropriate, copper wired receptacle that

is properly installed and grounded in accordance

with all local codes and ordinances or in the

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within

42 inches (107 cm) of your washer's water inlet. The

faucets MUST be 3/4 inch (1.9 cm) garden hose type

so inlet hoses can be connected. Water pressure MUST

be between 30 and 120 pounds per squareinch (maximum

unbalance pressure, hot vs. cold, 10 psi.) Your water

department can advise you of your water pressure.

DRAIN REQUIREMENTS

I. Drain capable of eliminating 17 gals (64.3 L) per

minute.

2. A standpipe diameter of I-I/4 in. (3.18 cm)

minimum.

3. The standpipe height above the floor should be:

Minimum height: 24 in. (61 cm)

Maximum height: 96 in. (244cm)

o OO

BACK I I

NOTE:

96 in.

(244 cm)

Max.

24 in.

(61 cm)

Min.

Drain hose attached to the washer can reach a 79

in. (201 cm) high standpipe. For higher standpipe,

use hose P/N 134889610, available from an

authorized parts distributor.

23¾"

(60.33)

ROUGH-iN DiMENSiONS

24"

(60.96)

inches(cm)

NOTE:

inches(¢m)

25/8"

(6.67)

_ - siDE

22" ,

(55.88)

255/8"

(65.09)

281/4"

(71.76)

35/8"

_(9.21 )

For pedestal installations, see additional installation instructions included with the pedestal.

For stacking installations, see additional installtion instructions included with the stacking kit.

For under counter installations, no special top is required.

27"

"1 (68.58)

_- 2½" (17.15)

____(6.35) 0 O0

_ ./-----_

33½"

:85.09)

BACK

i -- w

4 23"

(58.42)

27"

(68.58)

LOCATION OF YOUR WASHER

DO NOT INSTALL YOUR WASHER:

I. Inan area exposed to dripping water or outside weather conditions. The ambient temperature should never be below 60 ° F

(15.6 ° C) for proper washer (detergent breakdown) operation.

2. In an area where it will come in contact with curtains or drapes.

3. In an area (garage or garage-type building) where gasoline of other flammables are kept or stored (including automobiles).

4. On carpet. Floor MUST be solid with a maximum slope of 1/2 in. per foot (1.27 cm per 30.5 cm). To ensure vibration or

movement does not occur, reinforcement of the floor may be necessary.

IMPORTANT

MINIMUM INSTALLATION CLEARANCES

When installed in alcove or closet:

Sides, Rear = 0 in. (0 cm)

Top = 0 in. (0 cm)

When installed in closet: Front = I in. (2.54 cm)

Closet door ventilation required: 2 Iouvered openings each 60 in2(387 cm2),3 in. (7.6 cm) from top and bottom of door.

UNPACKING

1. Cut the shipping carton along the dotted line along the bottom. Removethe carton.

2. Using a rug, blanket or piece of cardboard to protect the floor, lay the washer on it's back.

3. Remove and savethe styrofoam base and shipping plug.

Shipping

Base Plug

4. Carefully return the washer to an

upright position.

Carefully move the washer to within

4 feet (122cm) of the final location.

Remove the following from the back

panel of the washer:

4 shipping bolts,

4 spacers,

I metal "P" clamp,

2 hose clips. Remove:

metal "P" clamp

.Removethe 4 plugs from the literature

pack located in the drum and install

them in the holes vacated by the

packaging spacers. 4 shipping_bbolts,

4 spacers. hose clips

Zewe/ing the Washer

Excessivenoise and vibration can be prevented by properly

leveling the washen

.For free standinq installation and with the washer in it's

final position, place a level on top of the washer. Adjust

the leveling legs so the washer is level front-to-rear and

side-to-side, and stable comer-to-corner.

Washer Connections

I. Run some water from the hot and cold

faucets to flush the water lines and

remove particles that might clog up

the water valve screens.

Remove the inlet hoses and rubber

washers from the plastic bag located

in the drum of the washer and install

the rubber washers in each end of the

inlet hoses.

Pressdown on alternate corners and sides and feel for the

slightest movement. Adjust the appropriate leg so the

washer is SOLID on the floor on ALLfour legs. Keep the

leveling leg extension at a minimum for best performance

of the washer.

3. Carefully connect the inlet hose marked "HOT" to the

outside "H" outlet of the water valve. Tighten by hand,

then tighten another 2/3 turn with pliers. Carefully connect

the other inlet hose to the inside "C" outlet of the water

valve. Tighten by hand, then tighten another 2/3 turn with

pliers. Do not crossthread or over-tighten these

connections.

4. Connect the inlet hose ends to the HOT and COLD water

faucets tightly by hand, then tighten another 2/3 turn with

pliers. Turn the water on and check for leaks.

NOTE: Use only new hoses.

2. For pedestal installations, See additional installation

instructions included with the pedestal.

iNSTALLATiON (CON'T)

Cable Tie

5. Attach drain hose hanger (shipped in washer tub) to

drain hose.

Place the hook end of the drain hose in the drain

opening. Secure the drain hose with the cable tie

(provided in the enclosure package) to the standpipe,

inlet hose, laundry tub, etc. so the hose does not pull

out from the force of the water.

7. Plug the power cord into a grounded outlet.

NOTE: Check to ensure the power isoff at a circuit breaker/fuse box before

plugging the power cord into an outlet.

8. Turn on the power at a circuit breaker/fuse box.

9. Readthe Operating Instructions and Owner's Guide provided with the washer.

They contain valuable and helpful information that will save you time and

money.

10. Runthe washer through a complete cycle. Check for water leaks and proper

operation.

1I. If your washer does not operate, please review the "Avoid ServiceChecklist"

in your Owner's Guide before calling for service.

12. Placethese instructions in a location near the washer for future reference.

NOTE: A wiring diagram and technical data sheet are located in an envelope

attached to the left hand side panel on the inside of the washer.

Pedestal

A pedestal accessory,MadelNa. APWD15W(White), APWD15GB (Glacier

Blue),APWD15P(Platinum)andAPWD15E(Black), specifically designed

for this washer may be used when elevating the washer for ease of use.

Failure to use accessories certified by the manufacturer could result in

personal injury, property damage or damage to the washer.

REPLACEMENT PARTS

If replacements parts are needed for your washeB contact the source where you

purchased your washer, call 1-800-944-9044, or visit our website,

www.frigidaire.com, for the Frigidaire Company Authorized Parts Distributor

nearest you.

Destroy the carton and plastic bags after the washer is unpacked.

Children might use them for play. Cartons covered with rugs, bedspreads, or

plasticsheetscan become airtight chambers causing suffocation. Placeall materials

in a garbage container or make materials inaccessible to children.

_The instructions in this manual and all other literature included with

this washer are not meant to cover every possible condition and situation that

may occun Good safe practice and caution MUST be applied when installing,

operating and maintaining any appliance.

Maximum benefits and enjoyment are achieved when all the Safety and

Operating instructions are understood and practiced as a routine with your 1

laundering tasks.

_Sujetacables

Sujetacables

Instalad6n (Con't)

5.Junte el porta manguera (seenvia dentro de

la tina de la lavadora) con la manguera del

drenaje.

6. Ponga el extremo del gancho de la manguera

de drenaje en la abertura del drenaje. Asegure

la manguera de drenaje con el cincho

(proporcionada dentro del paquete) al tubo del

drenaje, a la alimentaci6n de agua, a la tuberia

de la entrada, a la tina del lavadero, etc. para

que la manguera no se salga con la fuerza del

agua.

7.Enchufe el cable tomacorriente en un contacto debidamente aterrizado.

NOTA: Aseg0rese de que la corriente este cortada en el interruptor /caja

de fusibles antes de enchufar el cable en el tomacorriente.

8.Encienda la corriente en el interruptor/caja de fusibles.

9. Lea lasInstrucciones para el funcionamiento y la Guia del propietario,

incluidas con la lavadora. Contienen informaciOn valiosa y 0til que le

ahorrara tiempo y dinero.

10.Haga funcionar la lavadora durante un cicIo completo. Compruebe

que no haya fugas de agua y que funcione correctamente.

11.Si su lavadora no funciona, lea la "Lista de comprobaciOn para evitar

el servicio" que seencuentra en la Guia del propietario, antes de Ilamar al

servicio t_cnico.

12.Guarde estas instrucciones en un lugar cercano a la lavadora para

poder referirse a elias en el futuro.

NOTA: Dentro de la lavadora, en el panel de servicio, se encuentra un

diagrama de cableado.

Pedestal

Este accesorio, pedestal, NOmero de Modelo APWD15W (Blanco),

APWD 15P (Platino), APWD 15GB (Azul Gladar) oAPWD 15E

(Negro), especificamente para esta lavadora puede set utilizado al

elevar la lavadora para la facilidad de uso. La falta de utilizar los

accesorios certificados pot el fabricante podia dar lugar a dahos corpo-

rales, a dahos materiales, o dahos a la lavadora.

PIEZAS DE REPUESTO

Si necesita piezas de repuesto para su lavadora, acuda al establecimiento

donde la compr6 Ilame al 1-800- 944-9044,0visite nuestroweb

sitio,www.frigidaire.com,para la digan Distribuidor autorizada de laspiezas

de Frigidaire Io mas cerca posible usted.

J_ Deseche la caja de cart6n y las bolsas de plastico una

vez que haya desembalado la lavadora. Los nihos podrian usarlas para

jugar. Lascajasde cart6n tapadas con alfombras, colchas u hojas de plastico

pueden convertirse en camaras herm_ticas, causando asfixia. Coloque

todos los materiales en el basurero o evite que los nihos tengan acceso a

ellos.

ll_ Las instrucciones que aparecen en este manual y las

demas guias incluidas con esta lavadora no pretenden cubrir todas las

condiciones y situaciones posibles que pueden ocurrir. DEBEtenerse sentido

corn0 n ycuidado alinstalar, operar y mantener cualquier electrodom_stico.

Se obtiene el maximo de beneficios y resultados cuando todas las

instrucciones de seguridad y de funcionamiento son comprendidas y

puestas en practica de forma rutinaria cada vez que se lava la ropa.

4. Concuidado,vuelvaacolocarla

lavadoraenposici6nverticalysaquelacaja.

5. Concuidado,muevalalavadoraaunos4pies

(122cm)desuubicaci6ndefinitiva.

6. SaqueIosiguientedelaparteposterior

delalavadora:

4pernos

4separadores

1abrazaderasdepresi6naliberar

cord6ndelservicio

2AbrazaderadelamangueradedesagCie

7. Quitelos4taponespequeflosquese

encuentranenelpaquetedelaliteraturadentrode

sulavadora,einstalelosenlosagujerosdonde

estabanlosseparadoresquefueronusadosenel

embalaje.

NOTA: En caso de que la lavadora vuelva a

sertransportada en el futuro, es necesarioque

vuelvan a ser instalados los aditamentos usados

Cable

El_ctrico

Quite:

abrazaderas

de"P',

4 pernos,

4sepatadotes___

en el transporte, para evitar daflos durante

el transporte de la lavadora. _"

INS TA LA CION CONEXIONES DE LA LAVAD ORA

Elexcesoderuidoyvibraci6ndelalavadorapuedeserprevenido I. Dejecorrerun pocoaguadelasllavesde

con la correcta nivelaciOn de la lavadora, agua caliente y fria para vaciar las lineas y

1. Para la instalaciOn delalavadora, elladebedeestaren la eliminarlasparticulasquepuedenobstruirlos

posiciOnfinal, colocaunnivelencimadelalavadora. Ajustelas filtrosdelasvalvulasdeagua.

patasniveladoras, paraqueesteestableencualquierposiciOn. 2. Aseg0resequelas manguerasdeentrada

Presioneenlasesquinasyenloslados, sisienteelmovimiento de agua tengan los empaques de hule

masleve. Ajustelas4patasdeformaapropiadahastaquela colocadosencadaunodelosextremos.

lavadora este bien sentada demanera SOLIDAsobreel piso. 3. Conecteconcuidadolamangueradeentradaalavalvula

Trate de tener las patas niveladoras Io menos extendidas de la de agua (en la lavadora)CALIENTE con la salida "H", apriete a

lavadoraposibleparaunmejorfuncionamientodelalavadora, manoyluegoapriete2/3 de vuelta con pinzas. Conectecon

2. Paralasinstalacionesdelpedestal, vealasinstruccionesde cuidado la manguera de entrada a la valvula de agua(en la

instalaciOn adicionales incluidas con el pedestal, lavadora)FRIA con la salida "C", apriete a mano y luego apriete

2/3 de vuelta con pinzas.

4. Conecte los extremos de las mangueras de entrada alas

Ilavesde agua CALIENTEy FRIAapretando bien a mano y apriete

otros 2/3 de vuelta con pinzas. Abra el agua y compruebe que

no haya fugas.

NOTA: Utilice solamente las mangueras nuevas provistas con

6ste electrodom_stico.

UBICACION DE SULAVADORA

NO INSTALE SU LAVADORA:

I. En una area expuesta a goteos de agua o a la intemperie. Latemperatura ambiente nunca debera estar por debajo de los GO

grados F(15,6 C) para que su lavadora funcione correctamente.

2. En un area donde estara en contacto con persianas o cortinas.

3. En un area (garaje o construcciOn similar) donde exista o se almacene gasolina u otros productos inflamables (inclusive

automOviles).

4. Sobre una alfombra. El piso DEBEser duro con una inclinaciOn maxima de 1/2 pulgaga por pie (1,27 cmpor cada 30,5 cm).

Para asegurarse de que no existan vibraciones ni ruidos, puede ser necesario reforzar el piso.

IMPORTANTE CLAROS MINIMOS DE INSTALACION

InstalaciOn en un armario: Lados, Parte Trasera, Parte Superior = 0 cm. (0 pulg.), Parte Delantera = 2.54 cm.(1 pulg.)

Aberturas de ventilaciOn requeridas en la puerta del armario: Dos rejillas de ventilaciOn cada 387 cm2 (60pulg?) - 7.6 cm. (3

pulg.) desde la parte inferior y superior de la puerta.

DESEMPAQUE

I. Corte la caja de carton a Io largo de la linea punteada al fondo de la caja. Retire la caja de carton.

2. Usando una manta, cobija o cubierta de carton para proteger el piso, recueste la lavadora sobre su parte trasera.

3.Retire y conserve la base de alastico del empaque de envio y las extensiones que sujetan el tambor de la lavadora.

Empaque de

Base Envio

23¾" DIMENSIONES PARA LA INSTALAOON

(60.33)

PO(cM)

Nota:

PO(cM)

25/8"

(6.67)

i i

m m

_- LA-DO -_

22"

(55.88) Ii

255/8"

(65.09)

35/8"

(9.21)

33½"

(85.09)

27"

L (68.58) ,

8_½_,_

/(21.59) "_ "_

O OO

m 2½"

(6.35)

PARTE POSTERIOR

m m •

23"

(58.42)

--6¾"

(17.15)

27"

(68.58) >

281/4"

(71.76)

Para instalaciones de pedestal, yea las instrucciones adicionales de instalaci6n incluidas con el pedestal.

Para instalaciones apiladas, vea las instrucciones adicionales de instalaci6n incluidas en el paquete para apilar

(stacking kit)

Para instalaciones debajo de una mesa o base, no se requiere ninguna tapa o cubierta especial,

Other manuals for SATF7000FS0

This manual suits for next models

Table of contents

Languages:

Other Electrolux Washer manuals

Electrolux

Electrolux EWT 12420 W User manual

Electrolux

Electrolux EW 550 F User manual

Electrolux

Electrolux WWF7524N3WA User manual

Electrolux

Electrolux EWT 136551 W User manual

Electrolux

Electrolux EWF 127443 W User manual

Electrolux

Electrolux EW6F6648Q8 User manual

Electrolux

Electrolux EWF12753 User manual

Electrolux

Electrolux EWT531 User manual

Electrolux

Electrolux EN2F5842CB User manual

Electrolux

Electrolux EW7F3846HS User manual

Electrolux

Electrolux EWF 1487 HDW2 User manual

Electrolux

Electrolux WAGL4E202 User manual

Electrolux

Electrolux EWF 128420 W User manual

Electrolux

Electrolux EWFLS70JIW1 User manual

Electrolux

Electrolux FLE120 User manual

Electrolux

Electrolux WASHING-MACHINES & WASHER-DRYERS User manual

Electrolux

Electrolux EWT 1066 EEW User manual

Electrolux

Electrolux W485S User manual

Electrolux

Electrolux EWFLW65H - 27'' Front-Load Washer Operating manual

Electrolux

Electrolux EWFLW65HTS - 27" Front-Load Washer User manual

Electrolux

Electrolux WAL6E200 User manual

Electrolux

Electrolux W4130S User manual

Electrolux

Electrolux EWS 1021 User manual

Electrolux

Electrolux EWS 1264 EDW User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Beko

Beko WKB 51231 PTMA manual