Electrolux EFLS210TIW User manual

EN FRONT LOAD WASHER

FR LAVEUSE Á CHARGEMENT FRONTAL

ES LAVADORA DE CARGA FRONTAL

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

INSTRUCCIONES DE INSTALACIÓN

157012090 April 2017

2Important Safety Instructions

Shipping Hardware

qFoam shipping support (in door gasket) removed and

stored

qShipping bolts and spacers removed from rear of

appliance and stored

qHole plugs (shipped in bag in drum) installed in holes

in backsheet

Leveling

qWasher is level, side-to-side and front-to-back

qCabinet is setting solid on all corners

Water Supply

qUse only new hoses and verify rubber sealing

washers are installed

qHOT supply is connected to HOT inlet and COLD

supply is connected to COLD inlet

qHOT and COLD water supply turned on

qNo leaks present at water supply connections or

appliance inlet connections -

recheck in 24 hours

Drain

qStand pipe or wall drain height minimum 24”

qDrain hose snapped in “U” channel (shipped in drum)

qDrain hose secured in place with cable tie (shipped in

drum)

Electrical Power

qHouse power turned on

qWasher plugged in

Final Checks

qInstallation Instructions and Use and Care Guide read

thoroughly

qDoor locks and water enters drum when cycle starts

qRegistration card sent in

Installation Checklist

Deﬁnitions

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

Recognize safety symbols, words and labels

Safety items throughout this manual are labeled with a

WARNING or CAUTION based on the risk type as described

below:

IMPORTANT

IMPORTANT indicates installation, operation or maintenance

information which is important but not hazard-related.

WARNING

WARNING indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

WARNING

Please read all instructions before using this washer.

CAUTION

CAUTION indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

DANGER

DANGER indicates an imminently hazardous situation which,

if not avoided, will result in death or serious injury.

Important Safety Instructions ...............................................2-3

Installation Requirements.....................................................4-5

Installation Instructions ........................................................6-9

Accessories..........................................................................10

Notes ...................................................................................11

Français................................................................................12

Español ................................................................................22

TABLE OF CONTENTS

Important Safety Instructions

NOTE

The electrical service to the washer must conform with local

codes and ordinances and the latest edition of the National

Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian

Electrical Code C22.1 part 1.

WARNING

FIRE HAZARD

For your safety the information in this manual must be

followed to minimize the risk of ﬁre or explosion or to prevent

property damage, personal injury or loss of life. Do not store

or use gasoline or other ﬂammable vapors and liquids in the

vicinity of this or any other appliance.

WARNING

SUFFOCATION HAZARD

Destroy the carton and plastic bags after the washer is

unpacked. Children might use them for play. Cartons covered

with rugs, bedspreads, or plastic sheets can become airtight

chambers causing suffocation. Place all materials in a

garbage container or make materials inaccessible to children.

IMPORTANT

The instructions in this manual and all other literature included

with this washer are not meant to cover every possible

condition and situation that may occur. Good safe practice

and caution MUST be applied when installing, operating and

maintaining any appliance.

Maximum beneﬁts and enjoyment are achieved when all

the Safety and Operating Instructions are understood and

practiced as a routine with your laundering tasks.

CAUTION

EXCESSIVE WEIGHT HAZARD

To avoid back or other injury, have more than one person

move or lift the washer.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Inlet hose (x2)

NOTE

Hoses are not included with washer purchase.

See “Accessories” section for various inlet hose

kits to ﬁt your speciﬁc installation.

Tools and materials needed for installation:

Adjustable

pliers

AND ANDOROR OR

Optional uni-

versal wrench

available from

dealer

Adjustable

wrench

3/8” or

10 mm

box wrench

Ratchet and

socket set

Carpenter’s level

IMPORTANT

DO NOT INSTALL YOUR WASHER:

1 ... in an area exposed to dripping water or outside

weather conditions. The ambient temperature should

never be below 60° F (15.6° C) to maximize detergent

effectiveness.

2 ... in an area (garage or garage-type building) where

gasoline or other ﬂammables (including automobiles) are

kept or stored.

3 ... on carpet. Floor MUST be solid with a maximum slope

of 1 inch (2.5 cm). To minimize vibration or movement,

reinforcement of the ﬂoor may be necessary.

4Installation Requirements

NOTE

GFI (Ground Fault Interrupter) receptacle is not required.

NOTE

Because of potentially inconsistent voltage capabilities, the

use of this washer with power created by gas powered

generators, solar powered generators, wind powered

generators or any other generator other than the local utility

company is not recommended.

CIRCUIT - Individual, properly polarized and grounded 15 amp.

branch circuit fused with 15 amp. time delay fuse or circuit

breaker.

POWER SUPPLY - 2 wire, with ground, 120 volt single phase,

60 Hz, Alternating Current.

OUTLET RECEPTACLE - Properly grounded 3-prong receptacle

to be located so the power supply cord is accessible when

the washer is in an installed position.

Grounding type

wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

56.5”

(144cm)

max.

24”

(61cm)

min.

Drain system requirements

1Drain capable of eliminating 6 gals (22.5 L) per minute.

2A standpipe diameter of 1-1/4 in. (3.18 cm) minimum.

3The standpipe height above the ﬂoor should be:

Minimum height: 24 in. (61 cm)

Maximum height: 56.5 in. (144 cm)

Water supply requirements

Hot and cold water faucets MUST be installed within hose

length of your washer’s water inlet. The faucets MUST be

3/4 inch (1.9 cm) with threading for laundry hose connection.

Water pressure MUST be between 10 and 110 psi. Pressure

difference between hot and cold cannot be more than 10 psi.

Your water department can advise you of your water pressure.

1 The washer MUST be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electrical shock by a path of least resistance for

electrical current.

2 Since your washer is equipped with a power supply

cord having an equipment-grounding conductor and

a grounding plug, the plug MUST be plugged into an

appropriate, copper wired receptacle that is properly

installed and grounded in accordance with all local codes

and ordinances or in the absence of local codes, with the

National Electrical Codes, ANSI/NFPA 70 (latest edition).

If in doubt, call a licensed electrician. DO NOT cut off or

alter the grounding prong on the power supply cord. In

situations where a two-slot receptacle is present, it is

the owner’s responsibility to have a licensed electrician

replace it with a properly grounded three prong

grounding type receptacle.

Ground requirements

Electrical system requirements

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Under Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

0”

(0cm)

0”

(0cm)

0”

(0cm)

Clearance requirements

WARNING

ELECTRICAL SHOCK HAZARD

Improper connection of the equipment grounding conductor

can result in a risk of electrical shock. Check with a licensed

electrician if you are in doubt as to whether the appliance is

properly grounded.

Installation Requirements

Washer Dimensions

1Drain hose length on washer approximately 55 inches (140 cm).

2Power supply cord length on washer approximately 59 inches (150 cm).

3Power supply cord length on Canadian dryer approximately 59 inches (150 cm).

water supply

connection on

rear of unit drain hose on

rear of unit1

ﬂoor line

68.5”

(174 cm)

24”

(60.5 cm)

electrical

supply on

rear of unit3

power cord on

rear of unit2

26” (66 cm)

to front of closed door

ﬂoor line

25” (64 cm)

to front of closed door

freestand washer

on ﬂoor

washer mounted on

optional pedestal

42” (107 cm)

to clear open door

43” (109 cm)

to clear open door

33.5”

(85 cm)

46”

(116.5 cm)

power cord on

rear of unit2

drain hose on

rear of unit1

water supply

connection on

rear of unit

24”

(60.5 cm)

6Installation Instructions

1 Remove door tape and empty drum contents, including

foam shipping brace inside rubber gasket of door.

2 Using a foam corner post from the packaging to protect

the ﬂoor, carefully lay the washer on its back.

Removing foam packaging

3 Remove styrofoam base and set it aside.

4 Carefully return the washer to an upright position.

5 Carefully move the washer to within 4 feet (1 m) of its ﬁnal

location.

WARNING

SUFFOCATION HAZARD

Destroy the carton and plastic bags after the washer is

unpacked. Children might use them for play. Cartons covered

with rugs, bedspreads, or plastic sheets can become airtight

chambers causing suffocation. Place all materials in a

garbage container or make materials inaccessible to children.

CAUTION

EXCESSIVE WEIGHT HAZARD

To avoid back or other injury, have more than one person

move or lift the washer.

IMPORTANT

Save styrofoam base and shipping braces for use to help

prevent washer damage during any future moves.

x 2

Installation Instructions

Locate hole plugs in the small bag supplied with washer

instruction guides. Cut them apart from each other and

insert them in the holes in washer back panel.

The drain hose is secured in place with two plastic

latching clamps. Press the locking tab and release the

drain hose.

Releasing Drain Hose

Installing hole plugs

x 3

x 2

IMPORTANT

Save all shipping bolts and spacers for future use. If the washer is

to be transported at a later date, the shipping hardware must be

reinstalled to help prevent shipping damage.

NOTE

Rubber expansion material on spacers may need time to

relax before they can be easily pulled through shipping hole.

Removing shipping hardware

Remove all of the following from the back of the washer:

• 3 shipping bolts

• 2 plastic clamps

• 3 shipping spacers

8Installation Instructions

raise lower

Leveling your washer

Excessive noise and vibration can be prevented by properly

leveling the washer.

1 For free standing installation and with the washer within

4 feet (1 m) of its ﬁnal location, place a level on top of the

washer.

2 Use adjustable pliers to adjust the leveling legs so the

washer is level front-to-rear and side-to-side, and stable

corner-to-corner.

3 Press down on alternate corners and sides and feel for

the slightest movement. Adjust the appropriate leg(s)

so the washer sits solidly on the ﬂoor on ALL four legs.

Keep the leveling leg extension at a minimum for best

performance of the washer.

Connecting inlet water

HOT HOT

COLD COLD

NOTE

For pedestal installations, see additional installation

instructions included with the pedestal.

NOTE

Hoses are not included with washer purchase. See

“Accessories” section for various inlet hose kits to ﬁt your

speciﬁc installation.

1 Run some water from the hot and cold faucets to ﬂush

the water lines and remove particles that might clog the

water valve screens and to determine which faucet is hot

and which is cold supply.

2 Connect the HOT inlet hose to the HOT inlet connection

on the washer and the COLD inlet hose to the COLD inlet

connection on the washer. Tighten by hand until snug.

Then tighten each supply connection another 2/3 turn

with pliers. Do not cross thread or over-tighten these

connections.

3 Connect the HOT inlet hose to the HOT water supply and

the COLD inlet hose to the COLD water supply. Tighten

by hand until snug. Then tighten each supply connection

another 2/3 turn with pliers. Do not bend, kink or pinch

water inlet hoses.

4 Turn on the water and check for leaks.

RUBBER WASHERS

MUST BE PRESENT

USE ONLY

NEW HOSES

Installation Instructions

CABLE TIE

IMPORTANT

Check to ensure the power is off at a circuit breaker/fuse box

before plugging the power cord into an outlet.

NOTE

A wiring diagram and technical data sheet are located under

the washer top panel, on top of the detergent dispenser

housing.

Grounding type

wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

Connecting drain and electrical

1 Snap one end of the drain hose hanger (shipped in

washer drum) onto the drain hose. Continue wrapping it

around the hanger and snap it in place.

2 Place the hook end of the drain hose in the drain

opening. Secure the drain hose with the cable tie

(provided in the enclosure package) to the standpipe,

inlet hose, laundry tub, etc. so the hose does not pull out

from the force of the water.

3 Plug the power cord into a grounded outlet.

4 Turn on the power at a circuit breaker/fuse box.

5 Carefully slide the washer to its ﬁnal position. Recheck

for level and rock corners for stability. Remove and

discard door tape.

6 Read the Use & Care Guide provided with the washer. It

contains valuable and helpful information that will save

you time and money.

7 If you have any questions during initial operation, please

review the “Service Prevention Checklist” in your Use &

Care Guide before calling for service.

8 Place these instructions in a location near the washer for

future reference.

10 Accessories

Replacement parts:

If replacements parts are needed for your washer, contact the

source where you purchased your washer or refer to your

Use

and Care Guide

for more information.

MATCHING STORAGE PEDESTAL*

White Pedestal - P/N EPWD200QSW

A storage pedestal accessory, speciﬁcally designed for this

washer may be used to elevate the washer for ease of use.

*Other colors may be available. Contact the source where you purchased

your washer.

DRYER STACKING KIT

P/N STA9

Depending on the model you purchased, a kit for stacking a

matching dryer on top of this washer may have been included

in the initial purchase of your dryer. If your model did not include

a stacking kit or you desire another stacking kit, you may order

one.

INLET HOSE KITS

Please call 866-233-8353 (in Canada, 800-265-8352) to explore

hose kit options that will meet your speciﬁc installation needs.

UNIVERSAL APPLIANCE WRENCH

P/N 137019200

A UNIVERSAL APPLIANCE WRENCH is available to aid in

dryer/washer/pedestal feet adjustment.

CAUTION

Failure to use accessories manufactured by (or approved

by) the manufacturer could result in personal injury, property

damage or damage to the washer.

WARNING

ELECTRICAL SHOCK HAZARD

Label all wires prior to disconnection when servicing controls.

Wiring errors can cause improper and dangerous operation.

Verify proper operation after servicing.

Other manuals for EFLS210TIW

Table of contents

Languages:

Other Electrolux Washer manuals

Electrolux

Electrolux UFW69K9165 User manual

Electrolux

Electrolux EWF147310W User manual

Electrolux

Electrolux EWF 1499 User manual

Electrolux

Electrolux EWT 136451 W User manual

Electrolux

Electrolux EW1024T User manual

Electrolux

Electrolux WH6-20LAC User manual

Electrolux

Electrolux EWC 10550 W User manual

Electrolux

Electrolux WAGLES7000 User manual

Electrolux

Electrolux Steam System EWF 167583 W User manual

Electrolux

Electrolux EWF 1230 User manual

Electrolux

Electrolux EIFLW55HIW - 27" Front-Load Washer Instruction Manual

Electrolux

Electrolux Washing machines User manual

Electrolux

Electrolux 7 Series User manual

Electrolux

Electrolux EIFLS55IIW - 27" Front-Load Steam Washer Installation instructions

Electrolux

Electrolux WASL 3 T User manual

Electrolux

Electrolux EW 1134 F Quick guide

Electrolux

Electrolux EWC 1150 User manual

Electrolux

Electrolux EW7F3846HS User manual

Electrolux

Electrolux W555H User manual

Electrolux

Electrolux EW 1230 F Quick guide

Electrolux

Electrolux EW2W3068E3 User manual

Electrolux

Electrolux EWF 14118 User manual

Electrolux

Electrolux EW6F429BC User manual

Electrolux

Electrolux EWM1000 User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Beko

Beko WKB 51231 PTMA manual