Elba OB60S4 User manual

NZ AU

1104144-ß1 09.12

590498A 09.12

OB60S4 & OB60S7

models

INSTALLATION INSTRUCTIONS

Built-in Oven

IMPORTANT SAFETY INSTRUCTIONS!

To avoid hazard, follow these instructions carefully before installing or using this appliance.

Please make this information available to the person installing the appliance - doing so could

reduce your installation costs.

This appliance must be installed and connected to the mains power supply only by a suitably

qualified person according to these installation instructions and in compliance with any applicable

local building and electricity regulations. Failure to install the appliance correctly could invalidate

any warranty or liability claims.

If the power supply cable is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualified person in order to avoid a hazard.

SAFETY AND WARNINGS

WARNING!

Electrical shock hazard

Always disconnect the appliance from the mains power supply before

carrying out any maintenance or repairs.

Connection to a good earth wiring system is essential and mandatory.

Alterations to the domestic wiring system must only be made by a

qualified electrician.

Failure to follow this advice may result in electrical shock or death.

WARNING!

Fire hazard

Do not use adapters, reducers, or branching devices to connect this appliance to

the mains power supply.

Failure to follow this advice may result in overheating, burning, or fire.

WARNING!

Cut hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

PRODUCT & CABINETRY DIMENSIONS

2.5 mm

16-20 mm

Product and cabinetry dimensions (mm)

OB60S4

OB60S7

Aoverall height* of product 597 597

Boverall width of product 595 595

Coverall depth of product (excluding handle and knobs) 567 567

Dheight of chassis 582 582

Ewidth of chassis 556 556

Fdepth of chassis 545 545

Gdepth of oven frame and control panel

(=distance between front of chassis and front of oven door, excl. knobs) 22 22

Hdepth of oven door when fully open

(measured from front of control panel) 435 435

Iminimum inside width of cavity 560 560

IIoverall width of cavity 600 600

Jinside height of cavity 585 585

JIoverall height of cavity 600 600

Kminimum inside depth of cavity 550 550

Lflush fitting cabinetry clearance 22 22

Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer’s instructions.

*All height measurements include mounted feet.

PRIOR TO INSTALLATION

UNPACKING THE OVEN

Before you install the oven, make sure that

the benchtop and oven cavity are square and level, and are the required dimensions

the installation will comply with all clearance requirements and applicable standards and regulations

a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The

isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the requirements)

the isolating switch will be easily accessible to the customer with the oven installed

there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for ease of installation and servicing

the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall

the oven will rest on a surface that can support its weight

the height from the floor suits the customer

you consult local building authorities and by-laws if in doubt regarding installation.

Important!

Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend

moisture-proofing the oven cavity.

LOWER TRIM

OVEN DOOR

LOWER TRIM

AIR FLOW

Feet

Important!

Do not lift the oven by the door handle.

Remove all packaging and dispose of it responsibly. Recycle items that you can.

Place the unpacked oven onto wooden blocks or similar supports to prevent damaging the lower trim. You may remove the feet, but ensure the oven does not sit on the lower trim

Important!

The lower trim ensures correct air circulation and allows the door to open and close without obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.

ELECTRICAL CONNECTION

SECURING THE OVEN TO THE CABINETRY

Important!

This oven must be connected to the mains power

supply only by a suitably qualified person.

This oven must be earthed.

Before connecting the oven to the mains power

supply, check that

the domestic wiring system is suitable for the power

drawn by the oven

(as specified on the rating plate)

the voltage corresponds to the value given on the

rating plate.

Model code Power Voltage

OB60S4 3070 W 220 - 240 V~

OB60S7 3070 W 220 - 240 V~

(L )

Unhook to open cover

Unscrew to open

cable clamp

Position the oven in the prepared cavity.

Important!

Do not lift the oven by the door handle.

Open the oven door fully.

Use the supplied screws to secure the oven to the cabinetry.

Important!

Do not over-tighten the screws.

Do not seal the oven into the cabinetry with silicone or glue. This makes future

servicing difficult. Fisher & Paykel will not cover the costs of removing the oven,

or of damage caused by this removal.

2.5 mm

7FINAL CHECKLIST

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change

at any time. For current details about model and specification availability in your country, please

visit our local website listed at the end of this document or contact your local Fisher & Paykel

dealer.

www.sherpaykel.co.nz www.sherpaykel.com.au

TO BE COMPLETED BY THE INSTALLER

Make sure the oven is level and securely fitted to the cabinetry and the oven

door opens and closes freely.

Make sure all the internal packaging has been removed from the oven

cavity.

Make sure all oven vents and openings are clear and are free of any

obstruction/damage.

Check the lower trim is still undamaged - open the oven door slowly to

its fully open position and check if there is adequate clearance between

the bottom of the door and the lower trim. This is to ensure correct air

circulation. Should the lower trim become damaged, straighten it and

ensure the oven door opens fully without obstruction.

Check that the power supply cable does not touch any metal parts that can

become hot during use.

Make sure that the isolating switch is easily accessible by the customer.

Turn the power to the oven on. On some models, the display should light up

and show 0:00.

Advise the customer to follow the instructions in their user guide in section

‘First use’.

Installer’s name:

Installer’s signature:

Installation company:

Date of installation:

LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER

This manual suits for next models

Table of contents

Popular Oven manuals by other brands

Bosch

Bosch HVA531NS0 instruction manual

Electrolux

Electrolux EOF6P46X user manual

NEFF

NEFF B44S32 5GB Series instruction manual

Combi

Combi BLODGETT BC142GDS Specifications

AEG

AEG COMPETENCE 311704300 Installation and operating instructions

Falcon

Falcon DOMINATOR PLUS G3106 Series Servicing instructions

Rational

Rational SCC WE 61G installation manual

Smeg

Smeg DOSPA38X User manuals

Electrolux

Electrolux air-o-convect 20 GN 2/1 user manual

Miele

Miele HR 1954-2 operating instructions

KHIND

KHIND OT50 instruction manual

Henny Penny

Henny Penny Smoker Box installation manual

Lang

Lang ECOD-AP Installation and operation instructions

AEG

AEG BEK455310M user manual

Frigidaire

Frigidaire FNGE90JGR user manual

Hotpoint

Hotpoint FE9 S831 JSH IX user manual

GE Advantium SCB2000 owner's manual

AEG

AEG DE401301DM user manual