Elba EDIC-K3082ST(BK) User manual
Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
BUILT IN INDUCTION COOKER
MODEL: EDIC-K3082ST(BK)
EIC-K7082ST(BK)
EIC-K6083ST(BK)
EIC-K7094FZ(BK)
2
We recommend that you read the instructions in this owner’s manual carefully
before using it for the best performance and to extend the lifespan of your appliance, as
it will provide you with all the instructions you require to ensure its safe installation, use
and maintenance.
Safety Precautions
Edges of the appliance may be sharp, extra cautions must be paid to avoid injury
cause by the sharp edges.
To ensure your safety, all electric appliances should only be installed or serviced
by qualified technician. If the supply cord is damaged, it must be replaced by the
authorized service center or similarly qualified technician in order to avoidhazard.
Do not place supply cord on the edge of table and counter, or near any heating
appliance.
In order to avoid electric shock, do not immerse supply cord, plug or other parts
into water.
Do not place the appliance near electric stove, heated oven, microwave or other
heat source.
In order to avoid burning or explosion, combustibles or flammable material
(curtains, cloth, wallpaper and others) should be kept away from the appliance.
Do not place plastic or other similar items on the cooktop.
This appliance does not come with a plug preassembled and it has to be properly
installed and earthed with a connecting fuse with the load of 15A (Model EDIC-
K3082ST(BK), EIC-K7082ST(BK) and 30A or a circuit breaker (EIC-K6083ST(BK)
& EIC-K7094FZ(BK)).
The glass surface may become hot during use. Please keep away from children
and never touch the glass with bare hands.
Disconnect the appliance from the power supply and wait until it is cool before carry
out cleaning or maintenance.
In order to avoid electric shock, never use metal wire brush to clean the appliance
as pieces of metal are easy to touch live part.
3
Never use metal scouring pads or sharp scrapers which will damage the glass
surface leading to broken or scratches.
In order to avoid burn or electric shock, never put too much food or metal utensils
on the cooktop.
Please make sure the hob has been switched off when it is not in used and
unplugged from the socket when you are planning not to use the appliance for a
longtime.
Other purpose except cooking is not allowed.
Do not rest heavy object on the glass surface. This may damage the glass.
Do not cook on a broken or cracked cooktop. If the cooktop surface has been
broken, switch off the appliance immediately at the electrical mains and contact the
service center.
Never leave the appliance unattended when in use.
This appliance is not intended for use by persons (including children) with reduced
physical sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Do not use a steam cleaner to clean your cooktop.
Do not cook the food directly on the glass surface without any cookingutensils.
4
Installation
Selection of installation equipment
1. Cut out the work surface according to the sizes shown in the drawing. For the
purpose of installation and use, a minimum of 50mm space shall be preserved
around the hole. Be sure that the thickness of the work surface is at least 30mm.
Please select heat-resistant work surface material to avoid larger deformation
caused by the heat radiation from the appliance. Installation as shown below:
A(mm)
B(mm)
C(mm)
D
E
760
50 mini
20 mini
Air intake
Air exit 5 mm
Under any circumstances, make sure the hob is well ventilated and the air inlet and
outlet are not blocked. Ensure the hob is in good working condition as shown above.
Note: The safety distance between the hotplate and the cupboard above the
hotplate should be at least 760mm.
5
Before locating the fixing brackets
The unit should be placed on a stable, smooth surface (use the packaging). Do not
apply force onto the controls protruding from the hob. Fix the hob on the work surface
by screw four brackets on the bottom of hob (see picture) after installation. Adjust the
bracket position to suit for different work surface’s thickness.
EDIC-K3082ST(BK) EIC-K6083ST(BK)
EIC-K7082ST(BK) EIC-K7094FZ(BK)
6
Connecting the hob to the mains power supply
The power supply should be connected in compliance with the relevant standard, or a
single-pole circuit breaker. The method of connection is shown below.
EIC-K6083ST(BK)
EIC-K7094FZ(BK)
1.
If the cable is damaged or needs replacing, this should be done by an authorized
technician using the proper tools, so as to avoid any accidents.
2.
If the appliance is being connected directly to the mains supply, an omnipolar circuit
breaker must be installed with a minimum gap of 3mm between thecontacts.
3.
The installer must ensure that the correct electrical connection has been made and it
complies with the safety regulations.
4.
The cable must not be bent or compressed and shall be checked regularly.
7
Product Overview
Top View
EDIC-K3082ST(BK)
EIC-K6083ST(BK)
3
4
1. Max. 1400W zone
2. Min/Max. 1800/2200W zone
3. Max. 1800W zone
4. Control panel
1
2
1
2
3
1. Min/Max. 1200/1500W zone
2. Min/Max. 1800/2100W zone
3. Control panel
8
EDIC-K3082ST(BK)
EIC-K7094FZ(BK)
EIC-K7082ST(BK)
Control Panel
1. Min/Max. 1800/2100W zone
2. Min/Max. 1800/2100W zone
3. Min/Max. 1800/2100W zone
4. Min/Max. 1800/2100W zone
5. Min/Max. 3000/3600W zone
(Flexi Slide)
6. Control panel
1. ON/OFF
2. Power Control
3. Boost Control
4. Child Lock
5. Heating Zone
6. Timer Control
1
2
3
5
6
5
5
2
4
1
3
4
6
1. Min/Max. 1800/2100W zone
2. Min/Max. 1800/2100W zone
3. Control panel
9
EIC-K6083ST(BK)
3
4
2
2
6
1
EIC-K7094FZ(BK)
5
1. ON/OFF
2. Power Control
3. Boost Control
4. Child Lock
5. Heating Zone
6. Timer Control
5
2
4
1
3
6
5
EIC-K7082ST(BK)
10
Using the Touch Controls
•
The controls respond to sensor touch, so you don’t need to apply any pressure.
•
Use the ball of your finger, not its tip.
•
You will hear a beep corresponding to the sensor touch function.
•
Make sure the controls are always clean, dry, and that there is no object (e.g. a
utensil or a cloth) covering them. Even a thin film of water may make the controls
difficult to operate.
Choosing the right Cookware
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the
same size as the cooking zone. Always centre your pan on the cooking zone.
Always lift pans off the hob –do not slide, or they may scratch the glass.
This manual suits for next models
3
Table of contents
Other Elba Cooker manuals
Elba
Elba EC 930 User manual
Elba
Elba EIC-K2026(BK) User manual
Elba
Elba EIC-K2022 User manual
Elba
Elba DUAL FUEL COOKERS Installation and operating instructions
Elba
Elba PX 96 990 AZ Technical manual
Elba
Elba EEC 566 WH Installation and operating instructions
Elba
Elba 126 EX 339 User manual
Elba
Elba N58 205 Series Technical manual
Elba
Elba EX 1266 M Technical manual
Elba
Elba EEC 866 WH Installation and operating instructions
Elba
Elba EGV 13 User manual
Elba
Elba EGC 536 WH Installation and operating instructions
Elba
Elba EPRC-A6456GE SS User manual
Elba
Elba EEC 863 Technical manual
Elba
Elba EIC-A2029 User manual
Elba
Elba PXE 62-640 ISG Technical manual
Elba
Elba 9L PX 860 Installation and operating instructions
Elba
Elba GAS OVEN SERIES User manual
Elba
Elba E K55 X 220 Technical manual
Elba
Elba EGC 833 series Technical manual
