Ekwb EK-Vector FTW3 RTX 2080 Ti Guide

All disclosures, notices and warranty conditions are being written on the back of the box.

Installation and mounting manual for EK-Vector FTW3 RTX 2080 Ti

Backplate:

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water

Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our

web site at www.ekwb.com for updates. Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

STEP 1: GENERAL INFORMATION. Sample picture of FTW3 RTX 2080 Ti graphics card.

STEP 2: PREPARING YOUR GRAPHICS CARD

First install EK-Vector FTW3 RTX 2080 Ti series water block according to its installation manual. If you have it already installed, please

check the picture below to see which mounting screws are to be left in their position and which are to be removed. Please remove the six (6)

M2.5x4 AX1 screws and their PVC washers as well (marked with arrow).

STEP 3: APPLYING THE THERMAL PADS

EK-Vector FTW3 RTX 2080 Ti features passive cooling of the printed circuit board and its components therefore it is mandatory to install the

enclosed thermal pad. Please install (Thermal Pad F –1,0mm (120x16)) and (Thermal Pad F –1.5mm (120x16)) as shown on the picture below.

You may need to trim the excess thermal pad.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION!

1. Thermal Pad F 1.0mm (EAN: 3830046996732)

2. Thermal Pad F 1.5mm (EAN: 3830046996749)

EK-VECTOR FTW3 RTX

2080Ti BACKPLATE

All disclosures, notices and warranty conditions are being written on the back of the box.

STEP 4: ATTACHING EK-Vector FTW3 RTX 2080 Ti TO THE GRAPHICS CARD

Take enclosed mounting screws and install them as shown on picture below. Use six (6) M2.5x7 AX1 screws, and tighten them using Philips head

screwdriver.

HINT: Do not tighten screws until they are all positioned in their mounting holes. The backplate has milled in standoffs, so there is no fear of over

tightening of the screws. Nevertheless do not exaggerate with screwing force as there is no need for it.

By all means users must also consider that this product is intended to be used only with EK-Vector FTW3 RTX 2080 Ti series water blocks. No

other 3rd party heat sinks or coolers are officially supported! EK does not offer any assistance or support in the latter application.

IMPORTANT DISCLOSURES

VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering

up the computer. We recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using city water pressure.

This will rupture the top of the housing and render the block unusable (and will void your warranty).While all efforts have been made to provide

the most comprehensive tutorial possible, EK Water Blocks assumes no liability expressed or implied for any consequential damage(s) occurring to

your equipment as a result of using EK Water Blocks cooling products, either due to errors or omissions on our part in the above instructions, or

due to failure or defect in the EK Water Blocks cooling products.

WARRANTY:

Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final

user. During this period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent

from whom it was purchased; (II) the product has been purchased by an end user and has not used for commercial purposes; (III) the product

has not been misused, handled carelessly, or used in a manner other than in accordance with the instructions provided describing its installation

and proper use. This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss

or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer. This warranty is voided if the

product comes in contact with aggressive UV additives or other improper liquids. EK blocks are sealed with warranty void circular label, which proves

that the block has withstood a pressure leak test. Removing it will void leak-free guarantee and not the guarantee on the product itself. Any other

RMA issues can be reported to EK Support at http://www.ekwb.com/support for further analysis.

REQUIRED TOOLS AND MOUNTING SCREWS:

Philips head screwdriver scissors

M2.5X7 AX1 Screw

Phillips head

screwdriver

Other manuals for EK-Vector FTW3 RTX 2080 Ti

This manual suits for next models

Table of contents

Other ekwb Computer Hardware manuals

ekwb

ekwb EK-FC1080 GTX Ti TF6 User manual

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... User manual

ekwb

ekwb EK User manual

ekwb

ekwb EK-Quantum Reflection Uni 140 D5 PWM D-RGB User manual

ekwb

ekwb EK-FC RX-480 User manual

ekwb

ekwb EK-Quantum Reflection PC-O11D XL D5 PWM... User manual

ekwb

ekwb EK-PRO GPU WB RTX A4090 User manual

ekwb

ekwb EK-Quantum Vector FE RTX 3090... User manual

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB User manual

ekwb

ekwb EK-SF3D Inflection Point EVO User manual

ekwb

ekwb EK-FB ASUS P7P55 KIT Guide

ekwb

ekwb EK-FB ASUS ROG ZE Monoblock User manual

ekwb

ekwb EK-FB MSI X299 GAMING PRO CARBON Monoblock User manual

ekwb

ekwb EK-XTOP Revo Dual D5 Serial Manual

ekwb

ekwb EK-Quantum Kinetic TBE DDC PWM Series User manual

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... User manual

ekwb

ekwb EK-FC780 GTX Ti Manual

ekwb

ekwb EK-PRO GPU WB AMP/Trinity RTX 4090 - Ni +... User manual

ekwb

ekwb EK-FC970 GTX TF5 TFX Series Manual

ekwb

ekwb EK-FCW8100 Guide

ekwb

ekwb EK-FC R9-290X Backplate Manual

ekwb

ekwb EK-FC770 GTX GW Guide

ekwb

ekwb GTX 1080 Ti Aorus Backplate Guide

ekwb

ekwb Supremacy EVO User manual

Popular Computer Hardware manuals by other brands

EMC2

EMC2 VNX Series Hardware Information Guide

Panasonic

Panasonic DV0PM20105 Operation manual

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 user manual

Gigabyte

Gigabyte B660M DS3H AX DDR4 user manual

Raidon

Raidon iT2300 Quick installation guide

National Instruments

National Instruments PXI-8186 user manual

Hauppauge

Hauppauge WinTV-HVR-2250 Quick installation guide

Kontron

Kontron CP6002 user guide

Manhattan

Manhattan 702843 user manual

Aphex

Aphex 230 instruction manual

AMD

AMD Phenom II Product data sheet

Intel

Intel NUC 12 Pro user guide

dbx

dbx Zone Pro 1260 user manual

Galaxy

Galaxy GHDX2-2430S-24F4D Installation and hardware reference manual

Intel

Intel AXXRMFBU4 Quick installation user's guide

Kontron

Kontron DIMM-PC/MD product manual

ST X-NUCLEO-SAFEA1B How to use

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 installation manual

ekwb EK-Vector FTW3 RTX 2080 Ti Guide

Popular Computer Hardware manuals by other brands