ekwb EK-FB ASUS Max4 Extreme Guide
All disclosures, notices and warranty conditions are being written on the back of the box. Released on 18hof May, 2011.
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box or our home page.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the
liquid seal is made using o-rings. The use of an algaecide and corrosion inhibitors is always recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION Sample photo of ASUS Maximus IV Extreme PCB design
STEP 2: PREPARING YOUR MOTHERBOARD
1. REMOVING STOCK COOLER. Remove all 8 screws holding the original heat-
pipe cooler / backplate assembly to the motherboard’s circuit board.
2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all
screws securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip,
as shown on sample photo) of the original thermal compound until the components and
circuit board are completely clean. EKWB does not recommend using any liquids for
removing paste.
3. APPLYING THERMAL COMPOUND
Apply thermal compound: lightly coat the NF200 (NB) and P67 PCH (SB chips with
for example Arctic Cooling MX-2 ™or MX-4 ™ thermal grease. EKWB recommends
to apply thermal grease in cross form for best performance (see sample picture).
4. CUTTING THERMAL PADS. Two (2) 90x15x1mm thermal pads are enclosed with your
EK-FB Max4 Extreme water block. You will have to cut the thermal pad in order to cover all
marked surfaces surface. (WARNING: DIMENSIONS ON PICTURES BELLOW ARE SCALED!)
5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow. (PLEASE REMOVE FOIL OF THERMAL PADS ON
BOTH SIDES PRIOR TO INSTALLATION.)
P67 Southbridge
NF200
bridge chip
CPU socket
Installation and mounting manual for EK-FB ASUS Max4 Extreme water block:
Mosfets
Apply thermal grease on
Northbridge (NF200) and
Southbridge (P67).
Place 1mm thermal pads here and make
sure all chips are covered.
All disclosures, notices and warranty conditions are being written on the back of the box. Released on 18hof May, 2011.
STEP 3: PREPARING YOUR WATER BLOCK
1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting
holes and place acetal standoffs on NB & MOSFET part of the waterblock (thickness 2,1
mm) so the holes are concentric. Use two 3,3mm acetal standoffs on the SB part of the
waterblock to make one 6,6mm standoff. Thermal paste provides enough adhesive force
for standoffs to stay in a place for easier installation. This is a crucial step!
2. PLACING BLOCK OVER MB. Place the motherboard on the inverted water blocks
or vice versa and attach them with enclosed screws as shown. Make sure that
mounting holes are aligned.
STEP 4: ATTACHING BLOCK TO MOTHERBOARD
MOUNTING THE BLOCK.
For
perfect thermal contact, the block does not use a spring mounting system; therefore when attaching be very careful to tighten all screws equally.
Tightening the screws beginning in the center of the block near the northbridge, and continue evenly outwards. Do not use too much pressure
on
screws, because motherboard might
bend and either cause bad contact with water block, or break a connection on the circuit board.
Use the enclosed screws and washers as shown in diagram below:
STEP 5: CHECKING FOR CONTACTS
Temporarily r
emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat
steps 3 and 4 to reattach the block. Block was tested on physical hardware. Due to height variations of chipset some differences may occur. In case you have problem with block
contacts please write to our support mail.
STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT
Screw in fittings as shown in picture, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. Please use spacer if you use fitting with G1/4 thread
longer than 5mm. Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. EKWB recommends using EK-PSC compression fittings with the EK-FB
Max4 Extreme series water blocks. The use of an market proved algaecide is always recommended for any liquid cooling system. You can use any opening as an inlet/outlet
port.
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors philips screwdriver 6 screws M2.5x6 DIN7985 2 screws M3x12 DIN7985 8 PVC washers
EK-PSC compression fitting
Two 3,3mm
standoffs combined
on the SB part of
the waterblock
2,1mm standoffs
Use two (2) enclosed M3x12 DIN7985
screws on the southbridge part of the
waterblock!
PVC washer
M2.5x6 DIN7985
screw
philips head screwdriver
ROG LED socket
This manual suits for next models
1
Table of contents
Other ekwb Computer Hardware manuals
ekwb
ekwb EK-FC980 GTX Strix Manual
ekwb
ekwb EK-FC Titan V User manual
ekwb
ekwb EK-FB ASUS M5E Guide
ekwb
ekwb EK-FC980 GTX Original CSQ Series Manual
ekwb
ekwb EK-Vector RTX Aorus 2080 User manual
ekwb
ekwb EK-FC R9-390X TF5 Series Manual
ekwb
ekwb EK-Classic Pump Reservoir 160 SPC PWM D-RGB Guide
ekwb
ekwb EK Series User manual
ekwb
ekwb EK-Quantum Vector Trinity RTX 3080/3090 User manual
ekwb
ekwb EK-FB KIT GA Z97X-SOC Force Guide
ekwb
ekwb EK-FC980 GTX Classy Manual
ekwb
ekwb EK-FC980 GTX Ti TF5 Series Manual
ekwb
ekwb R9-290X Series Guide
ekwb
ekwb EK-XRES Revo D5 User manual
ekwb
ekwb EK-FC470 GTX Manual
ekwb
ekwb EK-Classic GPU Water Block RTX 3080/3090... User manual
ekwb
ekwb EK-FC Titan Z water block Manual
ekwb
ekwb EK-XTOP Revo D5 PWM Manual
ekwb
ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... User manual
ekwb
ekwb EK-Vector Trio RTX 2080 User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
