EKT TSP01 User manual

The slim multi-sensor TSP01 has PIR, temperature and illumination, 3

sensors function in one, based on Z-WaveTM technology. Z-WaveTM is a

wireless communication protocol designed for home automation,

specifically to remotely control applications in residential and light

commercial environments. The technology uses a low-power RF radio

embedded or retrofitted into home electronics devices and systems,

such as lighting, home access control, entertainment systems and

household appliances.

This device is one component of the Z-WaveTM sensor system and is

designed to work with all other Z-WaveTM enabled devices in a home

control network. The device adopt the Z-WaveTM 400 series chip, when

your Z-WaveTM network system is all made by Z-WaveTM 400 series

devices. The network system will have the advantages as below.

•Concurrent multi-channel support reduces external interference.

•Better RF range, improve about 10 meters in indoor.

•Support 100 Kbps transmit speed, speed up communication.

Adding to Z-WaveTM Network

There are two tamper keys in the device, one is in the back side,

another is in the front side. They have the same function. Both of them

can inclusion, exclusion, reset or association from Z-WaveTM network.

In the first time, add the device into the Z-WaveTM network. First, make

sure the primary controller is in the inclusion mode. And then power on

the device, just take out the insulation Mylar in the back side of the

device. The device will auto start the NWI (Network Wide Inclusion)

mode. And it should be included in 5 seconds. You will see the LED

light ON one second.

Function Description

Inclusion

1. Have Z-WaveTM Controller entered inclusion mode.

2. Pressing tamper key three times within 1.5 seconds

will enter inclusion mode.

3. After inclusion successful, the device will wake to

receive the setting command from Z-WaveTM

Controller about 20 seconds.

Exclusion

1. Have Z-WaveTM Controller entered exclusion mode.

2. Pressing tamper key three times within 1.5 seconds

will enter exclusion mode.

Node ID has been excluded.

Reset

1. Pressing tamper key four times within 1.5 seconds

and do not release the tamper key in the 4th

pressed, and the LED will turn ON.

2. After 3 seconds the LED will turn OFF, after that

within 2 seconds, release the tamper key. If

successful, the LED will light ON one second.

Otherwise, the LED will flash once.

3. IDs are excluded and all settings will reset to

factory default.

www.ekt2.com

Electronics Katrangi Trading

Z-WAVE TSP01

User Manual

Association

1. Have Z-WaveTM Controller entered association

mode.

2. Pressing tamper key three times within 1.5 seconds

will enter association mode.

Note: The device support 2 groups. The group 1 is for

receiving the report message, like triggered event,

temperature, illumination etc. The group 2 is for light

control, the device will send the “Basic Set” command

to this group.

•Including a node ID allocated by Z-WaveTM Controller means

inclusion. Excluding a node ID allocated by Z-WaveTM

Controller means exclusion.

•Failed or success in including/excluding the node ID can be

viewed from Z-WaveTM Controller.

Notice 1: Always RESET a Z-WaveTM device before trying to add it to a

Z-WaveTM network.

Notice 2: When the device into NWI mode, any tamper key and

sensor functionality will useless. The NWI will timeout after 30 seconds.

Z-WaveTM Notification

After the device adding to the network, it will wake-up once per day in

default. When it wake-up it will broadcast the “Wake Up Notification”

message to the network, and wake-up 10 seconds for receive the

setting commands.

The wake-up interval minimum setting is 30 minutes, and maximum

setting is 120 hours. And the interval step is 30 minutes.

If the user want to wake-up the device immediately, please remove the

front cover, and press the tamper key once. The device will wake-up 10

seconds.

Z-WaveTM Message Report

* Motion Report:

When the PIR motion detected, the device will unsolicited to send the

“Sensor Binary Report” to the nodes in the group 1.

Sensor Type: Motion (0x0C)

Sensor Value: 0xFF

* Tamper Report:

When the 2 tamper keys in the device are pressed over 5 seconds. The

device will into the alarm state. In that state, if any one of the tamper

keys be released, the device will unsolicited to send the “Sensor Binary

Report” to the nodes in the group 1.

Sensor Type: Tamper (0x08)

Sensor Value: 0xFF

* Temperature Report:

When the PIR motion detected, the device will unsolicited to send the

“Sensor Multilevel Report” to the nodes in the group 1.

Sensor Type: Temperature (0x01)

Note: To disable this functionality by setting the configuration setting

N0.5, the bit5 of the value to 1.

*** Temperature differential report ***

This function default is disabled, to enable by setting the configuration

setting NO.6 bit6 to 1.

When the temperature plus or minus three degree Fahrenheit (1.67

degree Celsius), the device will report temperature information to the

nodes in the group 1.

The device will measure the temperature in every 64 seconds. And if

the temperature is over 140 degree Fahrenheit (60 degree Celsius), the

device also report in each measurement.

* Illumination Report:

When the PIR motion detected, the device will unsolicited to send the

www.ekt2.com

Electronics Katrangi Trading

“Sensor Multilevel Report” to the nodes in the group 1.

Sensor Type: Luminance (0x03)

Note: To disable this functionality by setting the configuration setting

N0.5, the bit4 of the value to 1.

* Timing Report:

Beside the event triggered could report message, the device also

support the timing unsolicited report of the status.

•Battery level report: Every 6 hours report once in default.

It could be changed by configuration setting NO. 10.

•Low battery report: When the battery level is too low, every 30

minutes will report once.

•Illumination level report: Every 6 hours report once in default.

It could be changed by configuration setting NO. 12.

•Temperature report: Every 6 hours report once in default.

It could be changed by configuration setting NO. 13.

Power Up Procedure

* Battery Power Check

When the power up, the device will detect the power level of the

battery immediately. If the power level is too low, the LED will continue

flash about 5 seconds. Please change another new battery.

* PIR Warm Up

When the power on, the PIR need to warm up before operation. The

warm up time about 1 minute, the LED will flash in every 2 seconds.

After finish the procedure the LED will light ON three times.

* NWI

When the power on, the device will check is it already adding to the

network? If doesn't, it will auto start the NWI mode. The LED will flash

in every second and continue 30 seconds. Until timeout or the device

successful to inclusion by controller.

* Wake

When the power on, the device will wake about 20 seconds. In this

duration, the controller can communicate with the device. Normally the

device is always sleeping to save the battery energy.

Function DIP Switch

There is one function DIP switch in front of the device.

Remove the front cover in the right top of the PCB, and also has mark

“M1” and “M2” for two switch.

M1 M2 Description

ON ON Test Mode.

ON OFF Security Mode.

OFF ON Home Automation Mode.

OFF OFF Program Mode. According to the configuration setting

NO. 5 to set the operation mode.

Operation Mode

There are three operation modes of the device. The user can choosing

the suitable mode for application.

There are three modes “Test”, “Home Automation” and “Security”.

“Test Mode” is for the user test the sensor function when installation.

“Home Automation Mode” focus in automatic to control the lighting

equipment. For convenience and save energy.

“Security Mode” focus in surveillance, warning.

When the event triggered, normally the LED won't indicated, unless the

battery is in the low level, the LED will flash once. And in the “Test

Mode” the LED also will light ON one second.

www.ekt2.com

Electronics Katrangi Trading

When the event triggered, the device will report the messages to the

nodes in the group 1. The messages also include the temperature and

the illumination level. The user can switch the report by configuration

setting NO. 5. Caution: In the “Home Automation Mode” if the

environment luminance higher than the setting, the device won't report

the message.

When the event triggered, if the environment luminance is less than

the setting of the configuration setting NO. 4, the device will emit the

signal to turn ON the lighting equipment, those nodes in the group 2.

And delay a while to turn OFF the lighting equipment. The delay time is

setting by the configuration setting NO. 9.

The PIR motion re-detected interval, in the “Test Mode” fixed to 6

seconds. In the “Home Automation Mode”, will start detect before turn

OFF the lighting equipment. In the “Security Mode”, according to the

setting of configuration setting NO. 8.

Notice: When the tamper key of the back side is in the released state,

the device always in the “Test Mode”, no matter the DIP switch setting.

www.ekt2.com

Electronics Katrangi Trading

Battery Installation

When the device report the low battery message. The user should

replace the battery to new one.

The way to open the front cover please follow below steps.

1. Using a tool like (1) to press 1-1 till hear a click sound

2. Hold the front cover and pull back

3. Hold the front cover and pull up

Replace the new battery and install the cover back.

1. Put the front cover bottom to 1-1, and press down.

2. Push the front cover top to 2-1.

Choosing a Suitable Location

1. The recommended mounting height is 160cm

2. Don't let the device facing the window or the sunlight.

3. Don't let the device facing the source of heat. Like heater.

www.ekt2.com

Electronics Katrangi Trading

Installation

1. In the first time, add the device into the Z-WaveTM network. First,

make sure the primary controller is in the inclusion mode. And then

power on the device, just take out the insulation Mylar in the back side

of the device. The device will auto start the NWI (Network Wide

Inclusion) mode. And it should be included in 5 seconds. You will see

the LED light ON one second.

2. Let Controller associate with Group 1 of the device, any light switch

that intend to be turned on when the device trig please associate to

Group 2 of the device.

3. In the accessory pack. There are two type of double coated tape,

one is thicker (hereinafter referred to as A tape) and another is thinner

(hereinafter referred to as B tape), you can use A tape for the test at

the beginning. The right way for A tape installation is stick it to the

position below tamper key. The thicker tape won't let the tamper key

close, so the sensor will enter the test mode, You may test if installed

position is good or not by this way.

After finish the test and decide to fix, then you can remove tape A, and

mounting the sensor by using tape B. This will close the tamper key

and let the sensor enter normal mode.

Z-Wave Configuration Settings

Notice: The data size of the configuration settings is 1.

NO. Name Default Valid

Values Description

2 Basic Set Level 255 1~100,

0xFF

Setting the BASIC command value to

turn on the light. The 0xFF(-1) means

turn on the light. For dimmer equipment

www.ekt2.com

Electronics Katrangi Trading

1 to 100 means the light strength.

3 PIR Sensitivity 70 0~99

PIR sensitivity settings.

0 means disable the PIR motion.

1 means the lowest sensitivity,

99 means the highest sensitivity.

High sensitivity means can detected long

distance, but if there is more noise signal

in the environment, it will re-trigger too

frequency.

4Light

Threshold 99 0~100

Setting the illumination threshold to turn

on the light. When the event triggered

and the environment illumination lower

then the threshold, the device will turn

on the light.

0 means turn off illumination detected

function. And never turn on the light.

1 means darkest.

99 means brightest.

100 means turn off illumination detected

function. And always turn on the light.

Notice: In none test mode, only the

value in 1 to 99 will enable the

illumination detected function and

update the illumination value.

5Operation

Mode

00~127 Operation mode. Using bit to control.

Bit0: 1 means security mode,

0 means home automation mode.

Bit1: 1 means enable test mode,

0 means disable test mode.

Notice:

Bit0 and bit1 will effect when the DIP

Switch setting to program mode.

If bit1 is enabled, the bit0 is useless.

Bit2: Reserved, always 1.

Bit3: Setting the temperature scale.

0: Fahrenheit, 1:Celsius

Bit4: Disable illumination report after

event triggered.

Bit5: Disable temperature report after

event triggered.

Multi-Sensor

Function

Switch

40~127

Multi-Sensor function switch. Using bit to

control.

Bit0: Reserved, always 1.

Bit1: Disable PIR integrate Illumination.

Bit2: Reserved, always 1.

Bit3: Reserved.

Bit4: Reserved.

Bit5: Reserved.

Bit6:Enable temperature monitoring.

When this bit enable, the temperature

changed 3 degree Fahrenheit, it will

report.

And also the temperature over 140

degree Fahrenheit, it will report every 64

seconds.

8PIR Re-Detect

Interval Time

33~127 In the security mode, after the PIR

motion detected, setting the re-detect

time. 8 seconds per tick, and minimum

time is 24 seconds, default tick is 3 (24

seconds).

Setting the suitable value to prevent

received the trigger signal too frequency.

Also can save the battery energy.

Notice: If this value bigger than the

configuration setting NO. 9. There is a

period after the light turned off and the

www.ekt2.com

Electronics Katrangi Trading

PIR not detecting.

9Turn Off Light

Time 44~127

After turn on the light, setting the delay

time to turn off the light when the PIR

motion is not detected. 8 seconds per

tick, and minimum time is 32 seconds,

default tick is 4 (32 seconds).

Auto Report

Battery Time 12 1~127

The interval time for auto report the

battery level. 30 minutes per tick and

minimum time is 30 minutes, default tick

is 12 (6 hours).

Auto Report

Illumination

Time

12 1~127

The interval time for auto report the

illumination. 30 minutes per tick and

minimum time is 30 minutes, default tick

is 12 (6 hours).

Auto Report

Temperature

Time

12 1~127

The interval time for auto report the

temperature. 30 minutes per tick and

minimum time is 30 minutes, default tick

is 12 (6 hours).

Z-Wave Supported Command Class

COMMAND_CLASS_CONFIGURATION

COMMAND_CLASS_VERSION

COMMAND_CLASS_SENSOR_BINARY_V2

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

COMMAND_CLASS_WAKE_UP_V2

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

COMMAND_CLASS_BATTERY

COMMAND_CLASS_BASIC

Specifications

Power by CR123A lithium battery.

Signal (Frequency):

868.42 MHz(EU),

908.42 MHz(US),

Range:

Minimum 30 meters indoor,

70 meters outdoor line of sight.

Operating Temperature: -10oC ~ 40oC

For indoor use only.

Specifications subject to change without notice due to continuing

product improvement.

Dimension: 28*96*23mm

www.ekt2.com

Electronics Katrangi Trading

Table of contents

Other EKT Accessories manuals

EKT

EKT NeuroSky Mindwave EEG User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual