Edge-Core ECS4810-12M Layer 2 Programming manual

Management Guide

www.edge-core.com

ECS4810-12M Layer 2

Gigabit Ethernet Switch

ANAGEMENT

UIDE

ECS4810-12M GIGABIT ETHERNET SWITCH

Layer 2 Switch

with 12 Gigabit Combination Ports (RJ-45/SFP)

ECS4810-12M

E042014/ST-R04

149100000142A

– 5 –

ABOUT THIS GUIDE

PURPOSE This guide gives specific information on how to operate and use the

management functions of the switch.

AUDIENCE The guide is intended for use by network administrators who are

responsible for operating and maintaining network equipment;

consequently, it assumes a basic working knowledge of general switch

functions, the Internet Protocol (IP), and Simple Network Management

Protocol (SNMP).

CONVENTIONS The following conventions are used throughout this guide to show

information:

OTE

Emphasizes important information or calls your attention to related

features or instructions.

AUTION

Alerts you to a potential hazard that could cause loss of data, or

damage the system or equipment.

ARNING

Alerts you to a potential hazard that could cause personal injury.

RELATED PUBLICATIONS The following publication details the hardware features of the switch,

including the physical and performance-related characteristics, and how to

install the switch:

The Installation Guide

Also, as part of the switch’s software, there is an online web-based help

that describes all management related features.

BOUT

HIS

UIDE

– 6 –

REVISION HISTORY This section summarizes the changes in each revision of this guide.

APRIL 2014 REVISION

This is the fourth version of this guide. This guide is valid for software

release v1.1.4.11. It includes information on the following changes:

◆Updated parameters for "Copying Files via FTP/TFTP or HTTP" on

page 127.

◆Updated parameters for "Setting the Time Manually" on page 135.

◆Updated parameters for "Setting the Time Zone" on page 138.

◆Updated parameters for "Configuring Telnet Settings" on page 141.

◆Updated parameters for "Configuring Transceiver Thresholds" on

page 170.

◆Updated parameters for "Creating QoS Policies" on page 294.

◆Updated parameters for "Configuring an Extended IPv6 ACL" on

page 368.

◆Updated parameters for "Configuring a MAC ACL" on page 370.

◆Updated Command Usage section for "Configuring Port Security" on

page 388.

◆Updated parameters for "Configuring LLDP Interface Attributes" on

page 425.

◆Updated parameters for "Setting SNMPv3 Views" on page 450.

◆Updated parameters for Table 31, "Supported Notification Messages,"

on page 454.

◆Updated parameters for "Specifying Static Interfaces for a Multicast

Router" on page 604.

◆Added the commands "clock summer-time (date)" on page 739, "clock

summer-time (predefined)" on page 741, and "clock summer-time

(recurring)" on page 742.

◆Added the chapter "Loopback Detection Commands" on page 1021.

◆Added the command "mvr6 priority" on page 1256.

◆Updated Command Usage section for the command "ip dhcp client

class-id" on page 1362.

BOUT

HIS

UIDE

– 7 –

FEBRUARY 2014 REVISION

This is the third version of this guide. This guide is valid for software

release v1.1.4.9. It includes information on the following changes:

◆Corrected description of the command "spanning-tree bpdu-filter" on

page 1051.

DECEMBER 2013 REVISION

This is the second version of this guide. This guide is valid for software

release v1.1.4.8. It includes information on the following changes:

◆Updated Parameter section for "Displaying Statistical History" on

page 165.

◆Added section for "Displaying Transceiver Data" on page 169 and

"Configuring Transceiver Thresholds" on page 170.

◆Added description of Timeout Mode and additional information for Port

Priority under "Configuring a Dynamic Trunk" on page 178.

◆Added description of Port Priority under "Mapping Protocol Groups to

Interfaces" on page 223.

◆Added section for "Configuring VLAN Translation" on page 231.

◆Added description for the parameters Action and Shutdown Interval

under "Configuring Loopback Detection" on page 244.

◆Added description of Priority parameter and bundle parameters under

"Creating QoS Policies" on page 294.

◆Added description of Counter parameter under "Binding a Port to an

Access Control List" on page 374.

◆Added the section "Configuring ACL Mirroring" on page 375, and

"Showing ACL Hardware Counters" on page 377.

◆Added description of MAC Filter and MAC Filter ID parameters under

"Configuring Port Security" on page 388.

◆Added description of DHCP Snooping Information Option Sub-option

Format and DHCP Snooping Information Option Remote ID parameters

under "DHCP Snooping Configuration" on page 410.

◆Added description of Circuit ID parameter under "Configuring Ports for

DHCP Snooping" on page 413.

◆Updated information in Parameter section under "Using the Ping

Function" on page 559.

◆Changed description of Restart DHCPv6 parameter under "Configuring

IPv6 Interface Settings" on page 568.

BOUT

HIS

UIDE

– 8 –

◆Added description of RA Guard parameters under "Configuring IPv6

Interface Settings" on page 568.

◆Added the section "Configuring DHCP Relay Service" on page 592.

◆Added description of Type and Expire parameters under "Specifying

Static Interfaces for a Multicast Router" on page 604.

◆Updated description of parameters under "Displaying Multicast Groups

Discovered by IGMP Snooping" on page 614.

◆Added the section "Multicast VLAN Registration for IPv6" on page 641.

◆Added the commands "show alarm" on page 694 and "show alarm-

status" on page 695.

◆Added the commands "show watchdog" on page 702 and "watchdog

software" on page 702.

◆Modified syntax of the command "delete" on page 708.

◆Added the command "upgrade opcode reload" on page 713 and "show

upgrade" on page 713.

◆Added the section "TFTP Configuration Commands" on page 713.

◆Added the command "terminal" on page 724.

◆Updated syntax for "logging host" on page 728.

◆Added the section "Synchronous Ethernet" on page 748.

◆Added the command "memory" on page 784 and "process cpu" on

page 785.

◆Changed command set for "Flow Sampling Commands" on page 795.

◆Added the section "PPPoE Intermediate Agent" on page 854.

◆Added the command "ip dhcp snooping information option circuit-id" on

page 895 and "clear ip dhcp snooping binding" on page 897.

◆Added the command "dos-protection tcp-udp-port-zero" on page 916.

◆Removed “tos” parameter from the command "permit, deny (Extended

IPv4 ACL)" on page 928.

◆Added “counter” parameter to the commands "ip access-group" on

page 930, "ipv6 access-group" on page 936, and "mac access-group"

on page 941.

◆Added the command "clear access-list hardware counters" on

page 946.

BOUT

HIS

UIDE

– 9 –

◆Added the parameter “hardware counters” to the command "show

access-list" on page 947.

◆Added the commands "discard" on page 953 and "show discard" on

page 959.

◆Added the command "transceiver-monitor" on page 967.

◆Updated description of commands "transceiver-threshold current" on

page 968, "transceiver-threshold rx-power" on page 969, "transceiver-

threshold temperature" on page 970, "transceiver-threshold tx-power"

on page 971, and "transceiver-threshold voltage" on page 972.

◆Added the command "show interfaces transceiver-threshold" on

page 974.

◆Added the command "lacp timeout" on page 987.

◆Added “access-list” parameter, and information about how to use this

parameter in the Command Usage section, for the command "port

monitor" on page 993.

◆Added parameters “brief” and “stp-enabled-only” for the command

"show spanning-tree" on page 1064.

◆Updated syntax for the command "erps domain" on page 1069.

◆Added commands for ERPS version 2, including "mep-monitor" on

page 1074, "non-revertive" on page 1077, "raps-def-mac" on

page 1082, "raps-without-vc" on page 1082, "rpl neighbor" on

page 1085, "version" on page 1087, "erps clear" on page 1089, "erps

forced-switch" on page 1089, and "erps manual-switch" on page 1091.

◆Added the command "non-erps-dev-protect" on page 1076.

◆Added “port-channel” parameter for the command "ring-port" on

page 1084

◆Added the command "clear erps statistics" on page 1088.

◆Added “statistics” parameter for the command "show erps" on

page 1093.

◆Updated syntax for "switchport dot1q-tunnel service match cvid" on

page 1117.

◆Added the section "Configuring VLAN Translation" on page 1125.

◆Added “priority” parameter to the command "protocol-vlan

protocol-group (Configuring Interfaces)" on page 1129.

◆Added “ipv6 dscp” parameter to the command "match" on page 1160.

BOUT

HIS

UIDE

– 10 –

◆Added the commands "bundle" on page 1163 and "priority" on

page 1171.

◆Added the command "clear ip igmp snooping statistics" on page 1195.

◆Added the commands "ip igmp authentication" on page 1204, "ip igmp

query-drop" on page 1208, "ip multicast-data-drop" on page 1208,

"show ip igmp authentication" on page 1209, "show ip igmp

query-drop" on page 1211, and "show ip multicast-data-drop" on

page 1212.

◆Added the sections "MLD Snooping" on page 1213 and "MLD Filtering

and Throttling" on page 1223.

◆Added the commands "mvr" on page 1233, "mvr proxy-query-interval"

on page 1236, "mvr source-port-mode dynamic" on page 1239, "clear

mrv groups dynamic" on page 1244, and "clear mrv statistics" on

page 1244.

◆Added parameters “query,” “summary,” and “mvr-vlan” to the

command "show mvr statistics" on page 1249.

◆Added the commands "mvr6 proxy-query-interval" on page 1258,

"mvr6 source-port-mode dynamic" on page 1260, "clear mvr6 groups

dynamic" on page 1265, and "clear mvr6 statistics" on page 1266.

◆Updated options for “interval” parameter for the command "ethernet

cfm cc ma interval" on page 1317.

◆Added “pattern” and “priority” parameters to the command "ethernet

cfm loopback" on page 1331.

◆Added the command "clear efm oam event-log" on page 1344.

◆Added the command "ipv6 dhcp client rapid-commit vlan" on

page 1364.

◆Updated Command Usage section for the command "ipv6 dhcp restart

client vlan" on page 1364.

◆Added the section "DHCP Relay Option 82" on page 1367.

◆Updated description of “netmask” parameter for the command "ip

address" on page 1374.

◆Added the command "traceroute6" on page 1402.

◆Added the command "ipv6 nd raguard" on page 1405 and "show ipv6

nd raguard" on page 1407.

◆Added the section "ND Snooping" on page 1409.

Other manuals for ECS4810-12M Layer 2

This manual suits for next models

Table of contents

Other Edge-Core Switch manuals

Edge-Core

Edge-Core AS6700-32X User manual

Edge-Core

Edge-Core AS7816-64X User manual

Edge-Core

Edge-Core ECS4150-28T User manual

Edge-Core

Edge-Core ECS3510-52T User manual

Edge-Core

Edge-Core ECS4130-28T User manual

Edge-Core

Edge-Core ECS4310-18T User manual

Edge-Core

Edge-Core AS5916-54XKS User manual

Edge-Core

Edge-Core ES4308-POE User manual

Edge-Core

Edge-Core Wedge100BF-65X User manual

Edge-Core

Edge-Core ES3628EA User manual

Edge-Core

Edge-Core ES3526VA-PoE User manual

Edge-Core

Edge-Core ECS1100-5P User manual

Edge-Core

Edge-Core ECS4650-54T User manual

Edge-Core

Edge-Core AS9726-32DB User manual

Edge-Core

Edge-Core AS5610-52X User manual

Edge-Core

Edge-Core ECS4510-52P User manual

Edge-Core

Edge-Core ECS2000-10P User manual

Edge-Core

Edge-Core ECS2100-10T User manual

Edge-Core

Edge-Core ECS4110-52T User manual

Edge-Core

Edge-Core AS4600-54T User manual

Edge-Core

Edge-Core ES4624-SFP User manual

Edge-Core

Edge-Core SMCGS26C-Smart User manual

Edge-Core

Edge-Core ECS3510-10PD Programming manual

Edge-Core

Edge-Core Minipack-AS8000 User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual