Edge-Core ECS4510-12PD Programming manual

www.edge-core.com

Web Management Guide

12-Port Gigabit Ethernet

Layer 2 Switch

ECS4510-12PD

Software Release v1.0.2.0

Web Management Guide

ECS4510-12PD Gigabit Ethernet Switch

Layer 2 Switch with

1 10/100/1000BASE-T (RJ-45) Port

1 10/100/1000BASE-T (RJ-45) PoE PSE Port,

8 10/100/1000BASE-T (RJ-45) PoE PD Ports,

and 2 Gigabit SFP Ports

E082013/ST-R01

149100000229A

– 3 –

How to Use This Guide

This guide includes detailed information on the switch software, including how to

operate and use the management functions of the switch. To deploy this switch

effectively and ensure trouble-free operation, you should first read the relevant

sections in this guide so that you are familiar with all of its software features.

Who Should Read This

Guide?

This guide is for network administrators who are responsible for operating and

maintaining network equipment. The guide assumes a basic working knowledge of

LANs (Local Area Networks), the Internet Protocol (IP), and Simple Network

Management Protocol (SNMP).

How This Guide is

Organized

This guide describes the switch’s web management interface. An introduction to

the switch’s key features is also provided. For information on initial configuration,

refer to the CLI Reference Guide.

The guide includes these sections:

◆Section I “Getting Started” — Includes an introduction to switch management.

◆Section II “Web Configuration” — Includes all management options available

through the web interface.

◆Section III “Appendices” — Includes information on troubleshooting switch

management access.

Documentation

This guide focuses on switch software configuration through the web interface.

For information on how to manage the switch through the Command Line

Interface (CLI), see the following guide:

CLI Reference Guide

For information on how to install the switch, see the following guide:

Installation Guide

For all safety information and regulatory statements, see the following documents:

Quick Start Guide

Safety and Regulatory Information

How to Use This Guide

– 4 –

Conventions The following conventions are used throughout this guide to show information:

Note:

Emphasizes important information or calls your attention to related features

or instructions.

Caution:

Alerts you to a potential hazard that could cause loss of data, or damage

the system or equipment.

Warning:

Alerts you to a potential hazard that could cause personal injury.

Revision History This section summarizes the changes in each revision of this guide.

August 2013 Revision

This is the first version of this guide. This guide is valid for software release v1.0.2.0.

– 5 –

CONTENTS

HOW TO USE THIS GUIDE 3

CONTENTS 5

FIGURES 15

TABLES 27

SECTION I GETTING STARTED 29

1INTRODUCTION 31

Key Features 31

Description of Software Features 32

System Defaults 37

2USING THE WEB INTERFACE 41

Connecting to the Web Interface 41

Navigating the Web Browser Interface 42

Home Page 42

Configuration Options 43

Panel Display 43

Main Menu 44

SECTION II WEB CONFIGURATION 61

3BASIC MANAGEMENT TASKS 63

Displaying System Information 64

Displaying Hardware/Software Versions 65

Configuring Support for Jumbo Frames 66

Displaying Bridge Extension Capabilities 67

Managing System Files 69

Copying Files via FTP/TFTP or HTTP 69

Saving the Running Configuration to a Local File 71

Setting the Start-up File 72

ONTENTS

– 6 –

Showing System Files 72

Automatic Operation Code Upgrade 73

Setting the System Clock 77

Setting the Time Manually 77

Setting the SNTP Polling Interval 78

Configuring NTP 79

Configuring Time Servers 80

Setting the Time Zone 84

Configuring the Console Port 85

Configuring Telnet Settings 87

Displaying CPU Utilization 88

Displaying Memory Utilization 89

Resetting the System 90

4INTERFACE CONFIGURATION 93

Port Configuration 94

Configuring by Port List 94

Configuring by Port Range 96

Displaying Connection Status 97

Configuring Local Port Mirroring 98

Configuring Remote Port Mirroring 100

Showing Port or Trunk Statistics 104

Displaying Transceiver Data 109

Configuring Transceiver Thresholds 110

Performing Cable Diagnostics 112

Trunk Configuration 114

Configuring a Static Trunk 115

Configuring a Dynamic Trunk 117

Displaying LACP Port Counters 123

Displaying LACP Settings and Status for the Local Side 124

Displaying LACP Settings and Status for the Remote Side 126

Configuring Load Balancing 127

Saving Power 129

Traffic Segmentation 131

Enabling Traffic Segmentation 131

Configuring Uplink and Downlink Ports 132

VLAN Trunking 134

ONTENTS

– 7 –

5 VLAN CONFIGURATION 137

IEEE 802.1Q VLANs 137

Configuring VLAN Groups 140

Adding Static Members to VLANs 142

Configuring Dynamic VLAN Registration 147

IEEE 802.1Q Tunneling 150

Enabling QinQ Tunneling on the Switch 154

Creating CVLAN to SPVLAN Mapping Entries 155

Adding an Interface to a QinQ Tunnel 157

Protocol VLANs 158

Configuring Protocol VLAN Groups 159

Mapping Protocol Groups to Interfaces 160

Configuring IP Subnet VLANs 162

Configuring MAC-based VLANs 164

Configuring VLAN Mirroring 166

6ADDRESS TABLE SETTINGS 169

Setting Static Addresses 169

Changing the Aging Time 171

Displaying the Dynamic Address Table 172

Clearing the Dynamic Address Table 173

Configuring MAC Address Mirroring 174

7SPANNING TREE ALGORITHM 177

Overview 177

Configuring Loopback Detection 180

Configuring Global Settings for STA 182

Displaying Global Settings for STA 187

Configuring Interface Settings for STA 188

Displaying Interface Settings for STA 192

Configuring Multiple Spanning Trees 194

Configuring Interface Settings for MSTP 199

8CONGESTION CONTROL 201

Rate Limiting 201

Storm Control 202

Automatic Traffic Control 204

Setting the ATC Timers 206

Configuring ATC Thresholds and Responses 207

ONTENTS

– 8 –

9CLASS OF SERVICE 211

Layer 2 Queue Settings 211

Setting the Default Priority for Interfaces 211

Selecting the Queue Mode 212

Mapping CoS Values to Egress Queues 215

Layer 3/4 Priority Settings 217

Setting Priority Processing to DSCP or CoS 218

Mapping Ingress DSCP Values to Internal DSCP Values 219

Mapping CoS Priorities to Internal DSCP Values 221

10 QUALITY OF SERVICE 225

Overview 225

Configuring a Class Map 226

Creating QoS Policies 230

Attaching a Policy Map to a Port 239

11 VOIP TRAFFIC CONFIGURATION 241

Overview 241

Configuring VoIP Traffic 242

Configuring Telephony OUI 243

Configuring VoIP Traffic Ports 244

12 SECURITY MEASURES 247

AAA Authorization and Accounting 248

Configuring Local/Remote Logon Authentication 249

Configuring Remote Logon Authentication Servers 250

Configuring AAA Accounting 255

Configuring AAA Authorization 260

Configuring User Accounts 263

Web Authentication 265

Configuring Global Settings for Web Authentication 265

Configuring Interface Settings for Web Authentication 266

Network Access (MAC Address Authentication) 268

Configuring Global Settings for Network Access 270

Configuring Network Access for Ports 271

Configuring Port Link Detection 273

Configuring a MAC Address Filter 274

Displaying Secure MAC Address Information 276

ONTENTS

– 9 –

Configuring HTTPS 277

Configuring Global Settings for HTTPS 277

Replacing the Default Secure-site Certificate 279

Configuring the Secure Shell 281

Configuring the SSH Server 283

Generating the Host Key Pair 284

Importing User Public Keys 286

Access Control Lists 288

Setting A Time Range 290

Showing TCAM Utilization 292

Setting the ACL Name and Type 293

Configuring a Standard IPv4 ACL 295

Configuring an Extended IPv4 ACL 296

Configuring a Standard IPv6 ACL 299

Configuring an Extended IPv6 ACL 300

Configuring a MAC ACL 302

Configuring an ARP ACL 304

Binding a Port to an Access Control List 306

ARP Inspection 307

Configuring Global Settings for ARP Inspection 308

Configuring VLAN Settings for ARP Inspection 310

Configuring Interface Settings for ARP Inspection 312

Displaying ARP Inspection Statistics 313

Displaying the ARP Inspection Log 314

Filtering IP Addresses for Management Access 315

Configuring Port Security 317

Configuring 802.1X Port Authentication 319

Configuring 802.1X Global Settings 320

Configuring Port Authenticator Settings for 802.1X 322

Configuring Port Supplicant Settings for 802.1X 326

Displaying 802.1X Statistics 328

DoS Protection 331

IP Source Guard 333

Configuring Ports for IP Source Guard 333

Configuring Static Bindings for IP Source Guard 335

Displaying Information for Dynamic IP Source Guard Bindings 337

ONTENTS

– 10 –

DHCP Snooping 339

DHCP Snooping Configuration 341

DHCP Snooping VLAN Configuration 342

Configuring Ports for DHCP Snooping 343

Displaying DHCP Snooping Binding Information 345

13 BASIC ADMINISTRATION PROTOCOLS 347

Configuring Event Logging 348

System Log Configuration 348

Remote Log Configuration 350

Sending Simple Mail Transfer Protocol Alerts 351

Link Layer Discovery Protocol 352

Setting LLDP Timing Attributes 353

Configuring LLDP Interface Attributes 355

Configuring LLDP Interface Civic-Address 358

Displaying LLDP Local Device Information 360

Displaying LLDP Remote Device Information 364

Displaying Device Statistics 372

Power over Ethernet 374

Enabling PSE Power 375

Configuring Power Source Check 376

Simple Network Management Protocol 377

Configuring Global Settings for SNMP 379

Setting the Local Engine ID 380

Specifying a Remote Engine ID 381

Setting SNMPv3 Views 383

Configuring SNMPv3 Groups 385

Setting Community Access Strings 391

Configuring Local SNMPv3 Users 393

Configuring Remote SNMPv3 Users 395

Specifying Trap Managers 397

Remote Monitoring 402

Configuring RMON Alarms 402

Configuring RMON Events 405

Configuring RMON History Samples 407

Configuring RMON Statistical Samples 410

Other manuals for ECS4510-12PD

Table of contents

Other Edge-Core Switch manuals

Edge-Core

Edge-Core Wedge-16X-AC User manual

Edge-Core

Edge-Core ES3526YA User manual

Edge-Core

Edge-Core AS5916-54XKS User manual

Edge-Core

Edge-Core ECS4510 Series User manual

Edge-Core

Edge-Core ES3510MA Programming manual

Edge-Core

Edge-Core ES4308-POE Programming manual

Edge-Core

Edge-Core AS7726-32X User manual

Edge-Core

Edge-Core ES3528-WDM Programming manual

Edge-Core

Edge-Core AS9926-24D User manual

Edge-Core

Edge-Core ES4528V-38 Programming manual

Edge-Core

Edge-Core ECS4510-12PD User manual

Edge-Core

Edge-Core ES3628EA User manual

Edge-Core

Edge-Core Wedge100BF-65X User manual

Edge-Core

Edge-Core ECS2100-10T User manual

Edge-Core

Edge-Core ECS4310-26T Programming manual

Edge-Core

Edge-Core AS5812-54T User manual

Edge-Core

Edge-Core ECS2100-10T User manual

Edge-Core

Edge-Core ES4626F Programming manual

Edge-Core

Edge-Core ECS5610-52S User manual

Edge-Core

Edge-Core ES3528M User manual

Edge-Core

Edge-Core AS7716-24SC User manual

Edge-Core

Edge-Core ES4624-SFP User manual

Edge-Core

Edge-Core AS7312-54XS User manual

Edge-Core

Edge-Core Wedge100BF-65X User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual