Edelbrock 5708 User manual

Catalog #5708

Brochure No. 63-5708

Rev. 10/06 - DA/mc

Page 1 of 2

EDELBROCK CAT-BACK EXHAUST SYSTEM

For 2000-2006 Toyota Tundra 3.7L & 4.7L V8, 2WD & 4WD

Catalog #5708

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new Edelbrock Cat-Back Exhaust System. If you have any

questions, please contact our Technical Hotline at: 1-800-416-8628 , 7am - 5pm, Monday-Friday, Pacific Standard

Time or e-mail us at [email protected].

Suggested Tools for Installation:

❑3/8" ratchet set and metric sockets ❑9/16” and 15mm wrench ❑Hacksaw

❑Jack and jackstands ❑Liquid penetrant and rubber lubricant

NOTE BEFORE YOU START:

This Edelbrock cat-back system comes with three different I-pipes. This is because some Tundras (between 2000-2006)

use three catalytic converters. Others use 2 catalytic converters and a resonator. If your vehicle came from the factory

with 3 catalytic converters, you will use I-pipe #25-3269 behind the third catalytic converter. If your vehicle came from

the factory with 2 catalytic converters and a resonator, you have the choice of either retaining the resonator for a more

melow exhaust tone, or eliminating the resonator which will give you a more aggressive exhaust tone. See appropriate

steps below.

DISASSEMBLY

Vehicles Equipped with 3 O.E. Catalytic Converters:

1. Remove the V-band clamp behind the rear most

catalytic converter.

2. Remove the stock hanger bars from their isolators

behind the third catalytic converter and remove the

O.E. exhaust system from the vehicle.

3. Install I-pipe #25-3269 behind the rear most

catalytic converter

(See Fig. 1).

Vehicles Equipped with 2 O.E. Catalytic Converters

& A Resonator:

1. If you are retaining your O.E., resonator, cut the

factory I-pipe 10” from the back of the O.E.

resonator. If you want to eliminate the O.E.

resonator, cut the factory I-pipe right where it enters

the O.E. resonator.

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

INSTALLATION INSTRUCTIONS

IMPORTANT NOTES:

•Support your vehicle with proper jackstands or ramps rated for the total vehicle weight. Place stands so that the rear

axle is allowed to hang free for easy system removal.

•These cat-back systems are engineered to fit stock catalytic converters or equivalent replacements. If you original

system has been modified, Edelbrock will not warranty fit or performance.

Fig. 1

2. Remove the stock hanger bars from their isolators

behind the resonator and remove the O.E. exhaust

system from the vehicle.

Catalog #5708

Brochure No. 63-5708

Rev. 10/06 - DA/mc

Page 2 of 2

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: (800) 416-8628

E-Mail: [email protected]

KIT CONTENTS

WARNING!!!

Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before driving!

ASSEMBLY

1. If using original resonator, use 2-1/2” band clamp on

end of I-pipe, #25-3248 and install over cut end of

resonator pipe, slip hanger into rubber isolator. I-

pipe #25-3248 must slide into resonator pipe a

minimum of 2”.

If not using original resonator, use 2-1/2” band

clamp on end of I-pipe #25-3247 and install over cut

end of Y-pipe. I-pipe #25-3247 must slide onto Y-

pipe a minimum of 2”. Cut I-pipe #25-3248 on

reduced end back 3-3/8” so to remove reduced end,

and deburr. Place 3” band clamp on front I-pipe.

Install rear I-pipe #25-3248 into front I-pipe, engage

hanger in rubber isolator.

NOTE: Snug clamps only so system can be adjusted

during installation.

Qty. Part # Desription

❑1 23-4081 Hanger Clamp Assy.

❑1 23-4082 Hanger Clamp Assy.

❑1 25-3247 I-Pipe Front

❑1 25-3248 I-Pipe Rear

❑1 25-3269 I-Pipe (3 catalytic converters)

Qty. Part # Desription

❑1 25-3249 Overaxle Pipe

❑1 25-3223 Tailpipe

❑1 25-55725 Muffler

❑3 46-6612 Band Clamps; 3”

❑2 46-6610 Band Clamps; 2-1/2”

2. Slip the muffler onto the intermediate pipe with a 3”

band clamp on the front. NOTE: Inlet end of muffler

is marked. Snug the clamp so you can adjust the

system later.

3. Install muffler hanger assembly #23-4081 into

muffler rubber isolators from the front of isolators

and slip over muffer outlet.

4. Install overaxle pipe into outlet of muffler.

5. Install overaxle hanger assembly #23-4082 by

slipping over outlet end of overaxle pipe and engage

hanger in rubber isolator.

6. Slip tailpipe onto overaxle pipe, install 3” band clamp

and snug clamp.

7. Align system for clearance to body, frame, and

driveline as you tighten the system from front to rear.

Hanger clamps can be used to properly align system.

8. Check for leaks and correct, if necessary.

Table of contents

Other Edelbrock Automobile Part manuals

Edelbrock

Edelbrock 66662 User manual

Edelbrock

Edelbrock 47522 User manual

Edelbrock

Edelbrock 3637 User manual

Edelbrock

Edelbrock Russell R09392S User manual

Edelbrock

Edelbrock Acura Integra 6737 User manual

Edelbrock

Edelbrock Performer RPM 1967 User manual

Edelbrock

Edelbrock 3821 User manual

Edelbrock

Edelbrock E-TEC 170 User manual

Edelbrock

Edelbrock Victor Jr. 289-302 User manual

Edelbrock

Edelbrock 6700 User manual

Edelbrock

Edelbrock 28385 User manual

Edelbrock

Edelbrock Performer Multipoint 3501 Technical document

Edelbrock

Edelbrock Predator Carburetor Owner's manual

Edelbrock

Edelbrock 7788 User manual

Edelbrock

Edelbrock 6652 User manual

Edelbrock

Edelbrock 3864 User manual

Edelbrock

Edelbrock Russell R09783 User manual

Edelbrock

Edelbrock 70207 User manual

Edelbrock

Edelbrock 3628 User manual

Edelbrock

Edelbrock 2832 User manual

Edelbrock

Edelbrock 352-428 User manual

Edelbrock

Edelbrock 66062 User manual

Edelbrock

Edelbrock Russell R09201 User manual

Edelbrock

Edelbrock Victor Series 6570 User manual

Popular Automobile Part manuals by other brands

Dakota Digital

Dakota Digital 650277 Installation

bosal

bosal 037031 Fitting instructions

Vintage Air

Vintage Air 571063 manual

GFB

GFB EX38 instruction manual

bosal

bosal 028091 Fitting instructions

Dodge

Dodge 8W-43 Wiring diagram

ICI

ICI Magnum FBM10DGN Installation

Volant Perfomance

Volant Perfomance 19435 installation instructions

BENDIX

BENDIX GEN 4 GEN 5 ABS manual

Vintage Air

Vintage Air 571065 manual

Rugged Ridge

Rugged Ridge 11503.13 installation instructions

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER instructions

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... maintenance

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G operating manual

Toshiba

Toshiba 48-1250 A instruction manual

aldes

aldes EHT2 installation instructions

Go Rhino

Go Rhino 24371T installation instructions

BBK

BBK 18950 installation instructions