Edelbrock 5213 User manual

Rev. 3/08 - AJ/mc

Catalog #5213, #5214

Brochure #63-5213

Page 1 of 2

Edelbrock Anti-Hop Bars

for 1964-1972 GM A-Body (Catalog #5213)

& 1978-1987 GM A/G Body (Catalog #5214)

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new anti-hop bars. If you have any questions, contact our

Technical Hotline at: 1-800-416-8628, 7 am to 5 pm, Monday-Friday, Pacific Standard Time or e-mail us at

[email protected].

Tools and Supplies Required:

❑ Jackstands ❑Torque Wrench (70 lb. min.)

❑Tire Chocks ❑Drill Motor

❑1/4” Drill Bit ❑Grease Gun

❑Floor Jack ❑Thread Lock Compound

❑7/16” & 3/4” Sockets and Wrenches

Caution: Installation requires being under raised vehicle. Support vehicle on level and stable ground using proper load

rated stands.

Note: Differential fill plug will not be accessible after installation. Check/change differential fluid before installation. The

right anti-hop will have to be removed to check fluid. After install, a fill plug style rear cover could be added.

1. Place vehicle on level stable ground (i.e. concrete or driveway). Chock front wheels at front and rear of tire

(Fig.1).

2. Raise rear of vehicle and support so to keep rear suspension loaded with vehicle weight. Removing rear tires is not

required but can be helpful.

3. During installation it is critical to maintain pinion angle. To do this, use floor jack to support pinion area of rear end

housing. NOTE: An angle finder can be used to measure pinion angle.

4. Remove left upper trailing arm bolt from rear end bushing and loosen front trailing arm bolt. Rotate trailing arm up

and out of way. On 1978-1987 A/G cars, remove brake line distribution block bolt.

5. Remove pressed-in O.E.M. rubber bushing with caution so as to not damage rear end housing.

6. Install left anti-hop bar with grease fitting facing rear of vehicle. (Left bar in #5213 will be stamped with #25-4027

and #5214 will be stamped with #25-4038). Minor moving of brake line may be required on some years and models.

On #5214 use 5/16” bolt, nut and bracket to relocate line

(Fig. 2).

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

INSTALLATION INSTRUCTIONS

Fig. 1 Fig. 2

Rev. 3/08 - AJ/mc

Catalog #5213, #5214

Brochure #63-5213

Page 2 of 2

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: 1-800-416-8628

E-Mail: [email protected]

7. Locate anti-hop bar on steel bushing and 1/2"

(Fig. 3)

snug at this time.

8. Install upper trailing arm on anti-hop bar urethane bushing.

9. Drill 1/4" hole through axle housing web using anti-hop bar as guide. NOTE: Make sure to have at minimum 1/4" of

material between bolt hole and web edge,

(Fig. 2).

10. Install 1/4" bolt, washer and nyloc nut. Tighten bolt to 20 ft/lbs.

11. Use thread lock compound on upper trailing arm and steel bushing bolts and torque to 70 ft/lbs.

12. Remove right upper trailing arm bolt from rear end bushing and loosen front trailing arm bolt. Rotate trailing arm up

and out of way.

13. Remove pressed in O.E.M. rubber bushing with caution so as to not damage rear end housing.

14. Install right anti-hop bar with grease fitting facing rear of vehicle. (Right bar in #5213 is marked #25-4028, #5214 is

marked #25-4039).

15. Locate anti-hop bar on steel bushing and 1/2 bolt

(Fig. 3)

, snug at this

time.

16. Install upper trailing arm on anti-hop bar urethane bushing.

17. Drill 1/4" hole through axle housing web using anti-hop bar as guide.

NOTE: Make sure to have minimum of 1/4" of material between bolt hole

and web edge.

18. Install 1/4" bolt, washer and nyloc nut torque to 10 ft/lbs.

19. Use thread lock compound on upper trailing arm and steel bushing bolts

and torque to 70 ft/lbs.

20. Although Edelbrock anti-hop bar bushings are prelubed, you may want to lub the bushings. Install zerk fitting covers

to prevent dirt and corrosion of the zerk fittings.

Check hardware tightness after 10 miles and on a regular basis.

Note: To further upgrade your suspension, use other Edelbrock suspension, springs and shocks. See an Edelbrock

dealer or go to our website at www.edelbrock.com.

Fig. 3

Steel Bushing

and Bolt

Grind here,

if needed.

This manual suits for next models

Table of contents

Other Edelbrock Automobile Part manuals

Edelbrock

Edelbrock 3843 User manual

Edelbrock

Edelbrock 2263 User manual

Edelbrock

Edelbrock 68003 User manual

Edelbrock

Edelbrock 65912 (Ceramic-Coated) User manual

Edelbrock

Edelbrock 1100 User manual

Edelbrock

Edelbrock 3842 User manual

Edelbrock

Edelbrock 5786 User manual

Edelbrock

Edelbrock 94 User manual

Edelbrock

Edelbrock 7798 User manual

Edelbrock

Edelbrock Victor Series 6570 User manual

Edelbrock

Edelbrock 70404 User manual

Edelbrock

Edelbrock 70402 User manual

Edelbrock

Edelbrock 70080 User manual

Edelbrock

Edelbrock Pro-Tuner User manual

Edelbrock

Edelbrock 72279 User manual

Edelbrock

Edelbrock 68752 User manual

Edelbrock

Edelbrock 70206 User manual

Edelbrock

Edelbrock 5782 User manual

Edelbrock

Edelbrock 61949 User manual

Edelbrock

Edelbrock 641570 User manual

Edelbrock

Edelbrock 2929 User manual

Edelbrock

Edelbrock 1472 User manual

Edelbrock

Edelbrock Russell R09320 User manual

Edelbrock

Edelbrock 67452 User manual

Popular Automobile Part manuals by other brands

Dakota Digital

Dakota Digital 650277 Installation

bosal

bosal 037031 Fitting instructions

Vintage Air

Vintage Air 571063 manual

GFB

GFB EX38 instruction manual

bosal

bosal 028091 Fitting instructions

Dodge

Dodge 8W-43 Wiring diagram

ICI

ICI Magnum FBM10DGN Installation

Volant Perfomance

Volant Perfomance 19435 installation instructions

BENDIX

BENDIX GEN 4 GEN 5 ABS manual

Vintage Air

Vintage Air 571065 manual

Rugged Ridge

Rugged Ridge 11503.13 installation instructions

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER instructions

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... maintenance

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G operating manual

Toshiba

Toshiba 48-1250 A instruction manual

aldes

aldes EHT2 installation instructions

Go Rhino

Go Rhino 24371T installation instructions

BBK

BBK 18950 installation instructions