Eaton Powerware 5110 User manual

Powerware 5110 UPS

User’s manual

The contents of this manual are the copyright

of the publisher and may not be reproduced (even extracts)

unless permission granted.

Every care has been taken to ensure the accuracy of

the information contained in this manual, but no liability

can be accepted for any errors or omission. The right

to make design modiﬁ cations is reserved.

Powerware 5110 UPS

ser

’

s manua

1023922 Revision A

Contents

Introduction

.................................................................................................

Features:

...................................................................................................................

Unit inspection

.........................................................................................................

Requesting for CE-declaration

................................................................................

Safety Instructions

......................................................................................

Battery connection required before use!

.....................................................

Connecting the Battery:

...........................................................................................

Installation and Operation:

..........................................................................

Typical applications

.................................................................................................

Indicators

....................................................................................................

Indicator table

.............................................................................................

Status Indicators

......................................................................................................

LED Indicator Table

..................................................................................................

LED Audible Alarm Table

........................................................................................

Battery replacement procedure:

..................................................................

Troubleshooting

.....................................................................................................

Speciﬁ cation*:

........................................................................................................

Service and Support

..................................................................................

User’s manual

350 - 1500 VA

1023922

Revision A

Introduction

The Powerware 5110 uninterruptible power system (UPS) ﬁ lters the input line from

line disturbances and protects your sensitive electronic equipment from ﬁ ve common

power problems such as power failures, power sags, power surges, over-voltage and

under- voltage.

Features:

Processor-controlled voltage regulation (AVR)

Eight outlets:

- Four with surge and backup protection

- Four with surge protection only

Data Line (Internet fax – modem – DSL) or telephone line surge protection

Cold start capability

USB communication port

User-replaceable batteries

Unit inspection

Once you have received the Powerware 5110 UPS product, you should remove the

package and inspect the product for shipping damage. If any damage is found, please

notify the carrier and your dealer. Please keep the shipping carton and the packing

foam in the event the product must be returned to the factory for service.

Requesting for CE-declaration

Can be downloaded from

http://www.powerware.com/Service_support/EMEA_certiﬁ cates.asp

Eaton Power Quality Oy

Koskelontie 13, FIN-02920 Espoo Finland

Phone: +358-9-452 661

Fax: +358-9-452 66 396

•

User’s manual

350 - 1500 VA

1023922

Revision A

Safety Instructions

ATTENTION

Maintenance, other than battery replacement must be performed by a

qualiﬁ ed technician. Failure to do so could result in an electrical shock.

Although the unit may be unplugged from utility power, hazardous

voltage still may be present through the battery.”

1. Place the Powerware 5110 UPS indoors in an area that has adequate airﬂ ow and

is free of excessive dust. Do NOT allow the UPS to be exposed to moisture, rain,

excessive heat, or direct sunlight.

2. Use of the Powerware 5110 UPS product in life support applications, where failure

of this equipment can reasonably be expected to cause failure of life support

equipment or to signiﬁ cantly affect its safety or effectiveness is NOT recommended.

3. Shut off the UPS and disconnect the input power cord from the wall outlet before

replacing the battery.

4. When replacing the battery, use the same number and type of battery

5. Do NOT dispose of battery in a ﬁ re. The battery may explode.

6. Do NOT open or mutilate the battery. They contain an electrolyte that is toxic and

harmful to the skin and eyes.

7. Proper disposal of the battery is required. Please refer to your local laws/

regulations regarding battery disposal.

8. Use tools with insulated handles to replace the battery to avoid personal injury.

Due to energy hazard, please remove wristwatches and jewelry such as rings when

replacing battery.

User’s manual

350 - 1500 VA

1023922

Revision A

Battery connection required before use!

Connecting the Battery:

Principal shown below for detailed information how to connect please refer to battery

replacement section.

Installation and Operation:

Following steps explain how to connect and operate the Powerware 5110 UPS.

1. Connect the UPS to a grounded power outlet.

2. Plug your computer, monitor or load to be protected into the “Battery Backup &

Surge Protection” outlets. (These outlets will provide emergency battery backup

power during power outages as well as protection from surges and spikes.)

Do NOT plug LASER PRINTERS into the “Battery Backup” outlets.

Do NOT plug ACCESSORY SURGE strips into the “Battery Backup” outlets.

3. Plug your peripheral equipment or non-critical loads (printer, scanner, fax, speaker,

etc.) into the “Surge Protection” outlets. (These outlets provide surge and spike

protection only, they will NOT provide battery backup power during a utility power

failure).

4. With your equipment turned off, switch on the UPS.

5. When the “On/Off” LED light is illuminated, turn on the connected equipment.

6. Connect your computer to the UPS using USB cable provided.

Install Power management software provided with the UPS

User’s manual

350 - 1500 VA

1023922

Revision A

Typical applications

Indicators

1. On/Off/Test Switch

One switch controls power to your equipment and performs a self-test to detect

overload/undercharge.

Turn on the UPS.

Press and hold the switch for more than one second and release the switch after the

beep. The UPS will start.

Turn off the UPS.

Press and hold the switch for more than one second and release the switch. The UPS

will shut down completely.

Perform Self-test.

The UPS will perform self-test for about 4.5 seconds when the UPS is turned on and

the utility power is present.

User’s manual

350 - 1500 VA

1023922

Revision A

2. Normal mode (Green)LED

Indicates the UPS is providing mains power to your equipment. When the LED is

blinking the UPS is providing power from the battery.

3. Fault (Red)LED

When blinking, LED could indicate an overload condition or that the battery should

be replaced. When the LED is always on it indicates a short or UPS fault. For details

please see Indicator Table.

4. Battery mode (Yellow)LED

Indicates the UPS is providing battery power to your equipment.

5. Four Battery Backup & Surge Protection Outlets

These three outlets not only provide full time surge protection but also provide

emergency battery backup power.

6. Four Surge Protection Outlets

These Three outlets provide full time protection from surge and spike.

7. Phone/modem/ADSL Protection

Built-in RJ11 jacks protect the Internet, phone or fax line from surges. Connect the line

in from the wall into the jack named “in” and connect the phone, modem, ADSL box to

the jack named “out”

8. USB Communication Port

The provided LanSafe monitoring and shutdown software can be automatically

conﬁ gured to save your ﬁ les and shut down your computer in the event of a prolonged

power outage.

9. Circuit Breaker

The button will protrude when the overload condition occurs. The UPS will switch off

of utility power. If the button protrudes, disconnect some non-essential equipment and

reset the circuit breaker by pushing the button inward.

10. Input Power Connector IEC C13

Plug your load power cable to power your UPS

User’s manual

350 - 1500 VA

1023922

Revision A

Indicator table

Status Indicators

The UPS provides both visual and audible status indicators. Visual indicators consist of

three LEDs to represent the following conditions:

On utility power operation

On battery power operation

UPS fault/alarm

LED Indicator Table

On Utility (AC mode)

Green Lighting

On Battery (Backup mode)

Yellow Lighting

Low Battery

Yellow Flashing

Fault/Output Short

Red Lighting

Overload/Check Battery

Red Flashing

LED Audible Alarm Table

On Battery (Backup mode)

Sounding every 5 seconds

Low Battery

Sounding (two beeps) every 5 seconds

Overload

Sounding every 0.5 seconds

Replace battery

Sounding (three beeps) every 30 seconds

Fault or output short circuit

Continuous sounding

Battery over charge

Sounding (three beeps) every 5 seconds

Battery replacement procedure:

1. Shut off the UPS and disconnect the input power cord from the wall outlet.

2. Open battery door.

3. Disconnect used battery. Connect new battery. (It is important that connectors be

ﬁ rmly attached to new batteries.)

4. Close battery door

5. Properly recycle used battery.

•

User’s manual

350 - 1500 VA

1023922

Revision A

5Ah batteries (350VA, 500VA models)

7Ah x 1 battery (700VA models)

Other manuals for Powerware 5110

Table of contents

Other Eaton UPS manuals

Eaton

Eaton Powerware 9170+ User manual

Eaton

Eaton 9EHD Series User manual

Eaton

Eaton 9PX 1000i User manual

Eaton

Eaton Powerware 9170+ User manual

Eaton

Eaton Powerware 5115 User manual

Eaton

Eaton 3S Assembly instructions

Eaton

Eaton 9SX 6000VA User manual

Eaton

Eaton 9E10000i User manual

Eaton

Eaton 3S 700 User manual

Eaton

Eaton EX RT 7 User manual

Eaton

Eaton BladeUPS none User manual

Eaton

Eaton Tripp Lite Series SmartPro Series Assembly instructions

Eaton

Eaton 5E650iUSB-AU User manual

Eaton

Eaton Powerware 9395 User manual

Eaton

Eaton Powerware 9355 User manual

Eaton

Eaton Powerware 9135 User manual

Eaton

Eaton 5S 1000 User manual

Eaton

Eaton DIN500AC Assembly instructions

Eaton

Eaton 9395 UPS User manual

Eaton

Eaton Powerware 9355 Parallel User manual

Eaton

Eaton Powerware 9155 User manual

Eaton

Eaton 93E User manual

Eaton

Eaton Powerware 9140 User manual

Eaton

Eaton Powerware 3105 UPS User manual

Popular UPS manuals by other brands

Pylontech

Pylontech Victron & Pylontech US5000 manual

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 user manual

Mecer

Mecer ME-1000-WTU user manual

Mustek

Mustek PowerMust 530(B) Plus Startup manual

Emerson

Emerson Liebert NXL series Operation and maintenance manual

MAKELSAN

MAKELSAN BOXER SERIES user manual

Block

Block PC-0524-400-0 manual

CyberPower

CyberPower CP585LCD user manual

CyberPower

CyberPower Office Tower Series UPS 1000 user manual

CyberPower

CyberPower BM100 quick start guide

Best Power

Best Power 610 quick start guide

Best Power

Best Power Unity/I UT3K user manual

Mustek

Mustek PowerMust 400 Offline user manual

Xantrex

Xantrex Trace 512 UR-UPS owner's manual

Forza

Forza SL-1501UL user manual

LEGRAND

LEGRAND keor 310081 quick start guide

ABB

ABB Conceptpower DPA 500 operating manual

ZincFive

ZincFive BC Series installation instructions