Eaton -66103 User manual

www.eaton.com

Network

Management

Card &

Modbus/

Jbus

(66103)

Installation manual

34003906EN_AE.fm Page 1 Vendredi, 19. décembre 2008 1:49 13

2 - 34003906EN/AE

34003906EN_AE.fm Page 2 Vendredi, 19. décembre 2008 1:49 13

34003906EN/AE - 3

The Network Management Card & Modbus/Jbus (66103) is recommended for central UPSs

protecting entire networks or for UPS units backing up critical loads. With the card installed, the UPS

has its own IP address and uses the local computer capabilities to:

●Supply web pages (http or https (SSL)) with information on status conditions and measurements/

settings/alarms,

●Integrate an SNMP-based NMS such as HP OpenView, IBM Tivoli Netview and Computer Associates

Unicenter,

●Communicate with shutdown modules installed on the protected servers (Network Shutdown

Module),

●Send e-mail and SMS messages,

●Control the ON/OFF function of the UPS and the outlets,

●Monitor the Environment Sensor (optional, cat. no. 66846).

●One Network Management Card & Modbus/Jbus (66103)

●One serial cable for configuration (34003918),

●One installation manual (34003906).

The Network Management Card & Modbus/Jbus (66103) is compatible with the

Pulsar

range UPSs

available since 2006.Note.

●If the technical level of the UPS is lower than that indicated in the table, contact EATON.

UNPACKING AND CHECKS

CHECK ON UPS VERSION

Important. Before installing the card, check that the UPS technical level (NT) is at least

equal to that indicated in the table below.

UPS Type Technical level (NT)

Pulsar 700/1000/1500 02

Pulsar M 2200/3000 03

Pulsar MX 4000/5000/10000 04

Pulsar MX Frame 15/20 kVA 01

34003906EN_AE.fm Page 3 Vendredi, 19. décembre 2008 1:49 13

4 - 34003906EN/AE

ETHERNET port

Service port (Settings/Sensor)

OVERVIEW

INDICATIONS

LED Colour Status Description

ACT Green ●OFF

●ON

●Flashing

●Card not connected to network

●Card connected to network, but no activity

●Port is sending/receiving

100M Orange ●OFF

●ON

●Port operating at 10 Mbits/s

●Port operating at 100 Mbits/s

LED Colour Status Description

UPS Data Green ●OFF

●ON

●Flashing

●Card starting

●Communicating with UPS

●Normal operation

Communication with UPS is operational

RS232 Orange ●OFF

●ON

●Flashing

●Configuration menu activated

●Normal operation

Configuration menu not activated

●Communication with Environment Sensor (option)

Settings/Sensor

66103

UPS data RS232

100M 10M

000623001C07

ETHERNET 10/100BT port

Service port (Settings/Sensor)

Orange LED: RS232 activity

Green LED: communication

with the UPS

Catalogue number

Orange LED: 10/100M

Green LED: connection +

activity

MAC address

Jbus/modbus port

34003906EN_AE.fm Page 4 Vendredi, 19. décembre 2008 1:49 13

34003906EN/AE - 5

The Network Management Card & Modbus/Jbus (66103) can be hot-plugged on all UPSs from

EATON equipped with a Minislot. It is not necessary to shutdown the UPS, disconnect the load or restart

the UPS.

●Remove the plastic cover of the Minislot.

●Note the MAC address of the card before inserting it.

●Insert and secure the card with the screws.

●Connect the ETHERNET cable.

●Check the ETHERNET port indications.

●Wait until the UPS Data LED flashes regularly (approx. two minutes), indicating that card start-up has

terminated correctly.

Note. Connection detection continues until the card has been connected to the network. Once

connection is made, card start-up continues.

Once the card has started, proceed as indicated below.

●Connect the serial cable to card’s service port and PC’s COM port

●Use a terminal emulator such as HyperTerminalTM with these settings

"Echo typed characters locally" option: disabled

●Type EATON (or eaton).

The main configuration menu is displayed:

IP SETTINGS

Bits per second Data bits Stop bits Parity Flow control

9600 8 1 none none

EATON

NETWORK MANAGEMENT CARD

1 : Reset

2 : Network configuration

3 : Set Login Password to Default

4 : Return to Default Configuration

5 : Jbus configuration

6 : Sensor configuration

0 : Exit

ETHERNET

ASI

Settings/Sensor

66103

UPS data RS232

100M 10M

34003906EN_AE.fm Page 5 Vendredi, 19. décembre 2008 1:49 13

6 - 34003906EN/AE

The card is configured by default with this service enabled. No manual configuration is required.The IP

parameters are automatically collected by the card.

From the main configuration menu: (see above)

●Press the 2 key (Network configuration).

●Press the 1 key(Read Network settings).

The settings supplied by the server are displayed:

●Note the IP address.

●Press the 0 key (Exit).

You can also use NMC Tool software utility to view the card IP adress

Provided on the Solution-Pac 2 CD-ROM or at www.eaton.com. It must be installed on a network

connected PC.

Manual configuration is required.

To set the network configuration, use terminal emulation (see above)

From the main configuration menu:

●Press the 2 key (Network configuration).

●Press the 2 key (Modify Network settings).

●Follow the instructions and enter the IP parameters:

Wait until "Done" is displayed, indicating that the IP parameters have been saved.

●Press the 0 key (Exit).

●Press the 1 key (Reset).

●Press the 2 key (Restart).

The card restarts with the new IP settings (after approx. one minute).

Your network is equipped with a BOOTP/DHCP server (default)

Network configuration :

MAC address : 00:06:23:00:1C:07

Mode : DHCP

IP address : 172.17.23.18

Subnet mask : 255.255.248.0

Gateway : 172.17.17

Your network is not equipped with a BOOTP/DHCP server

1 : Read Network settings

2 : Modify Network settings

3 : Set ethernet speed

0 : Exit

For each of the following questions, you can press "Return" to

select

the value shown in braces, or you can enter a new value

Should this target obtain IP settings from the network?[N]N

Static IP address [172.17.16.16]?172.16.1.82

Subnet mask IP address [255.255.0.0]? 255.255.255.0

Gateway address IP address [0.0.0.0]? 172.17.17.1

Done

34003906EN_AE.fm Page 6 Vendredi, 19. décembre 2008 1:49 13

34003906EN/AE - 7

To check whether the

Network Management Card

& Modbus/Jbus (66103)

is operational after

installation and configuration, proceed as follows.

●Run a browser

●Enter in the address bar:

http://IP address/ (e.g. http://172.16.1.82/)

●The home page is displayed

●Set the time by clicking the Time command.

●Continue configuration via the sections in the Settings menu.

This manual provides all the information required to install and configure the

Network Management

Card

& Modbus/Jbus

(66103).

For more information on the supervision, control and configuration functions offered by the

Network

Management Card

& Modbus/Jbus

(66103), see the user manual on the

Solution-Pac 2

CD-ROM or

in the Products/Power Management section of the

www.eaton.com/powerquality

site.

ACCESS TO SUPERVISION

USER MANUAL

34003906EN_AE.fm Page 7 Vendredi, 19. décembre 2008 1:49 13

8 - 34003906EN/AE

The Environment sensor is a Network Management Card & Modbus/Jbus option. It is available

from EATON (cat. no 66846).

The sensor remotely monitors the UPS environment by regularly measuring the temperature and

humidity, and checking the states of two external contacts. It can also send alarms (e-mail, SNMP trap)

tripped by pre-set thresholds.

Connection is made via the Service port (Settings/Sensor) on the Network Management Card &

Modbus/Jbus. The sensor is detected automatically. Configuration and supervision use a menu that

may be accessed directly from the home page. For more information, see the user manual of the

Network Management Card & Modbus/Jbus.

SENSOR CONNECTION (option)

66102

Settings/Sensor

ETHERNET

100M 10MUPS data RS232

On = ink

Blink = Act

ETHERNET

66103

UPS data RS232

100M 10M

34003906EN_AE.fm Page 8 Vendredi, 19. décembre 2008 1:49 13

34003906EN/AE - 9

RS232 link configuration and connection

RS485 link configuration and connection

For proper operation, the polarity of EIA RS485 2-wire and 4-wire lines must be set at only one point

and the lines terminated at the end.

Polarity

Normally, the master of the network sets the polarity of the line. The receiver inputs have a true failsafe

feature wich eliminates the need for external bias resistors and ensures a logic high output level when

the inputs are open or shorted. This guarantees that the receiver outputs are in a known state before

communication begins and when communication ceases.

Termination

Termination is used to match impedance of a node to the impedance of the transmission line being

used. When impedance are mismatched, the transmitted signal is not completely absorbed by the load

and a portion is reflected back into the transmission line. The termination line is not necessary if the

speed on the line is much less than 115Kbauds

The default setting of the RS485 is a 4 wires configuration without polarity and without termination.

SA1 switches are used to make the termination and the topology of the line (2 or 4 wires). The

termination resistance value is 166 Ω.

SA1 description:

1: reserved

2: reserved

3: link termination between T- to R- (2 wires configuration) if set to ON

4: connection T- to R- (2 wires configuration ) if set to ON

5: connection T+ to R+ (2 wires configuration ) if set to ON

6: reserved

7: reserved

8: link termination between R+ and R- if set to ON

JBUS/MODBUS

Txd RxdSG

43 2 1

SA1

SA2

Pin Function

1 Received data (input)

2 Not connected

3 Transmitted data (output)

4 Not connected

5 Signa ground

SA2

OFF

RD = (A')

TD = (B)

TD = (A)

0 V

RS485

RD = (B') R-

R+

T-

T+

0 V

SA1

SA2

SA1

OFF

SA2

OFF

SA2

SA1

34003906EN_AE.fm Page 9 Vendredi, 19. décembre 2008 1:49 13

10 - 34003906EN/AE

2 wires connection

Card settings of an intermediate cubicle

Others settings

SA1

SA2

SA1

OFF

SA2

OFF

SA2

SA1

L +

43 2 1

L -

L- L-

L+ L+

L- L-

L+ L+

polarity

connection

if end

of the line

polarity

transmit/receive

data

transmit/receive

data

transmit/receive

data

termination

Master unit Card of an end-of-line cubicle

connection

if end

of the line

3V3

SA1-3

3V3

SA1-3

Card of an intermediate cubicle

SA2

OFF

8 6 5 4 3 2 1

SA1

OFF

8 6 5 4 3 2 1

SA1

Link without polarity and without termination.

SA2

OFF

8 6 5 4 3 2 1

SA1

OFF

8 6 5 4 3 2 1

SA1

Link with termination.

34003906EN_AE.fm Page 10 Vendredi, 19. décembre 2008 1:49 13

Table of contents

Other Eaton Network Card manuals

Eaton

Eaton Modbus MS Card User manual

Eaton

Eaton Powerware Series Programming manual

Eaton

Eaton Network Card-MS User manual

Eaton

Eaton Network Management Card User manual

Eaton

Eaton Network-M2 User manual

Eaton

Eaton Network Card-MS User manual

Eaton

Eaton Network-MS User manual

Eaton

Eaton 34003991EN/EB User manual

Eaton

Eaton Network-M3 User manual

Eaton

Eaton Network-M2 User manual

Eaton

Eaton POW-R-COMMAND 1000 User manual

Eaton

Eaton DeviceNet Product Operated Network Interface Manual

Eaton

Eaton Power Xpert Meter 2000 User manual

Eaton

Eaton PXGMS Power Xpert Gateway Minislot UPS User manual

Eaton

Eaton DeviceNet Starter Network Adapter D77B-DSNAP User manual

Eaton

Eaton QSNAP User manual

Popular Network Card manuals by other brands

FirstComm

FirstComm OBiWiFi5G Setup guide

Sun Microsystems

Sun Microsystems Interface Adapter user guide

TRENDnet

TRENDnet TU2-ETG user guide

YASKAWA

YASKAWA SI-EN3 Technical manual

Paradyne

Paradyne BitStorm 2600 IP DSLAM installation guide

Belkin

Belkin F5D7050 user manual

3Com

3Com EtherLink 3C509B quick guide

TRENDnet

TRENDnet TEG-PCITX user guide

Cisco

Cisco MC16E installation guide

Delta Electronics

Delta Electronics Braking Modules VFDB Series instruction sheet

TwinMOS

TwinMOS Booming user manual

Dialogic

Dialogic Media Board DM/V1200BTEPEQ installation guide

Buffalo

Buffalo AirStation WLI-PCM-L11GP user manual

National Instruments

National Instruments NI 9234 operating instructions

Hama

Hama 49276 Operating instruction

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Product data

Compaq

Compaq Wireless LAN 100 specification

Bose

Bose PowerMatch Dante quick start guide