Dynabrade Dynangle 14200 User manual

Disassembly Instructions - 0.7 hp. Dynangle Air Motor

Models: 14200

Important: Use these instructions along with the tool parts page or manual.

Notice: Shut off the air supply and depress throttle lever to deplete the remaining air.

• Carefully disconnect the tool from the air supply hose. • Remove the cover and the abrasive

belt. • Use the Special Repair Tools designed for the disassembly and assembly of this motor.

Motor Disassembly:

1. Use a 1/8" hex key to loosen the 95530 Screw.

Remove the motor from the belt housing.

1/8" hex key

1/8" Hex Key

2. Use a 19 mm wrench to hold the motor spindle. By hand, or with groove pliers, grasp the

drive wheel and remove it. Turn counterclockwise.

19 mm Wrench

3. Carefully fasten the 01739 Housing in a vise with aluminum or bronze jaws so that the

spindle is pointing up.

Use a 1-1/2" crowfoot wrench to remove the 01748 Exhaust Cover.

Turn counterclockwise.

Remove the 01744 Silencer.

1-1/2" crowfoot wrench

Pull the motor out of the housing.

4. Fasten the 96346 Bearing Separator (2") around the 01028 Cylinder. Place the separator

and the motor in the 96232 Arbor Press (#2) so that the rotor spindle is pointing down.

Use a 5/32" or 4 mm diameter flat end drive punch to push the rotor out of the 02649

Bearing.

96346 Bearing Separator

5. Use the 96213 Bearing Removal Tool and the arbor press to remove the 02649 Bearing

from the rear bearing plate.

96346 Bearing Separator

96213 Bearing Removal Tool

6. Fasten the 55025 Rotor in the vise with aluminum or bronze jaws and use an adjustable

wrench to remove the 01708 Rotor Nut. Turn counterclockwise.

Remove the 01007 Bearing, 01008 Bearing Plate, shims, and 01010 Spacer.

Motor Disassembly Completed.

Clean and inspect parts before assembling.

Assembly Instructions - 0.7 hp. Dynafile III Air Motors

Motor Assembly:

1. Install the 01010 Spacer onto the rotor.

Install .003" (~0.80 mm) shim thickness into the 01008 Front Bearing Plate.

Install the 01007 Bearing into the front bearing plate.

Install the bearing and plate onto the rotor.

.003" (~0.80 mm)

shim thickness

01010 Spacer

2. By hand, install the 01708 Rotor Nut. Pull the front bearing plate forward to take movement

out of the bearing. Check the clearance between the rotor and plate.

Use a .001" (~0.03 mm) thick feeler gauge. Notice: The clearance should be

.001"-.0015" (~0.03-0.04 mm). If the rotor/plate clearance needs adjustment, repeat

steps 1 and 2. Remove or add shims as required.

.001"-.0015"

(~0.03-0.04 mm)

3. Use a 19 mm crowfoot and a torque wrench to tighten the 01708 Rotor Nut.

(T to 17 N•m/~150 in. lbs.)

T to 17 N•m/~150 in. lbs.

Other Dynabrade Sander manuals

Dynabrade

Dynabrade Nitro ROB1 Series Guide

Dynabrade

Dynabrade 09L1000 User manual

Dynabrade

Dynabrade Dynalocke 52760 Guide

Dynabrade

Dynabrade 53271 Guide

Dynabrade

Dynabrade Dynorbital Supreme 56800 Guide

Dynabrade

Dynabrade 57900 Guide

Dynabrade

Dynabrade 58040 User manual

Dynabrade

Dynabrade 51612 Guide

Dynabrade

Dynabrade 56801 User manual

Dynabrade

Dynabrade 10710 User manual

Dynabrade

Dynabrade 52510 User manual

Dynabrade

Dynabrade 52657 Guide

Dynabrade

Dynabrade 57900 Guide

Dynabrade

Dynabrade FB8 Guide

Dynabrade

Dynabrade 51520 Quick start guide

Dynabrade

Dynabrade 50320 User manual

Dynabrade

Dynabrade 58035 Installation and operation manual

Dynabrade

Dynabrade Dynorbital-Spirit 21000 Manual

Dynabrade

Dynabrade Dynorbital 57610 User manual

Dynabrade

Dynabrade 52503 Installation instructions

Dynabrade

Dynabrade Nitro ROB2 Series Guide

Dynabrade

Dynabrade 10727 User manual

Dynabrade

Dynabrade 57400 User manual

Dynabrade

Dynabrade 48500 Guide

Popular Sander manuals by other brands

Oliver

Oliver 6305 owner's manual

Jet

Jet 22-44 Pro-3 Operating instructions and parts manual

Makita

Makita M9204 technical information

Makita

Makita M9204 instruction manual

Craftsman

Craftsman 351.215131 Operator's manual

Clarke

Clarke Woodworker CBS1-5B Operation & maintenance instructions

Chicago Pneumatic

Chicago Pneumatic CP9778 Operator's manual

Nitto Kohki

Nitto Kohki BB-20 instruction manual

Ferm

Ferm FEOS-135 user manual

Unior

Unior 1510 Operating instruction

stayer

stayer ls1200 operating instructions

Jet

Jet JSG-96 Operating instructions and parts manual

Parkside

Parkside PDS 290 B2 Operation and safety notes

Status

Status XPA Series Original instructions

Clarke

Clarke EZ Sand Operator's manual

Craftsman

Craftsman 113.22521 owner's manual

Craftsman

Craftsman 113.225831 owner's manual

CLAS

CLAS OP 1429 manual