Dynabrade 51520 Quick start guide

Other Dynabrade Sander manuals

Dynabrade

Dynabrade 52450 User manual

Dynabrade

Dynabrade Dynabug 57920 User guide

Dynabrade

Dynabrade 50347 User guide

Dynabrade

Dynabrade 52413 Installation instructions

Dynabrade

Dynabrade Dynorbital 57130 User manual

Dynabrade

Dynabrade 57900 Guide

Dynabrade

Dynabrade 10725 User manual

Dynabrade

Dynabrade 51584 Guide

Dynabrade

Dynabrade 52410 User manual

Dynabrade

Dynabrade 50371 Installation instructions

Dynabrade

Dynabrade 57900 User manual

Dynabrade

Dynabrade DynaFine 10800 Installation instructions

Dynabrade

Dynabrade Dynorbital EXTREME X31V User manual

Dynabrade

Dynabrade 58040 User manual

Dynabrade

Dynabrade 10600 Installation instructions

Dynabrade

Dynabrade 51570 Guide

Dynabrade

Dynabrade 52597 User manual

Dynabrade

Dynabrade 18066 Guide

Dynabrade

Dynabrade 52900 Operating instructions

Dynabrade

Dynabrade 10390 User guide

Dynabrade

Dynabrade 51612 Guide

Dynabrade

Dynabrade 10727 User manual

Dynabrade

Dynabrade Dynorbital-Spirit 59000 Guide

Dynabrade

Dynabrade 50320 User manual

Popular Sander manuals by other brands

Oliver

Oliver 6305 owner's manual

Jet

Jet 22-44 Pro-3 Operating instructions and parts manual

Makita

Makita M9204 technical information

Makita

Makita M9204 instruction manual

Craftsman

Craftsman 351.215131 Operator's manual

Clarke

Clarke Woodworker CBS1-5B Operation & maintenance instructions

Chicago Pneumatic

Chicago Pneumatic CP9778 Operator's manual

Nitto Kohki

Nitto Kohki BB-20 instruction manual

Ferm

Ferm FEOS-135 user manual

Unior

Unior 1510 Operating instruction

stayer

stayer ls1200 operating instructions

Jet

Jet JSG-96 Operating instructions and parts manual

Parkside

Parkside PDS 290 B2 Operation and safety notes

Status

Status XPA Series Original instructions

Clarke

Clarke EZ Sand Operator's manual

Craftsman

Craftsman 113.22521 owner's manual

Craftsman

Craftsman 113.225831 owner's manual

CLAS

CLAS OP 1429 manual

Disassembly Instructions - Wet, Stone Polisher

Model: 51520

Important: Use these instructions along with tool parts page or manual.

Notice:

Shut off air supply and depress throttle lever to deplete air.

Disconnect tool from air supply hose.

Shut off water supply faucet and disconnect.

Remove all accessories (abrasive product, backup disc, and flanges) from tool.

Motor Disassembly:

1. Push against collar of 96227 Fitting and pull 95579 Water Line tubing from fitting.

2. Install 95492 Screws (5/16"-18 SHC) in two handle bosses on housing.

Fasten 95492 Screws in vise to hold tool with 51546 Valve Body pointing up.

Use a 3 mm hex key to remove 96296, 95916 Screws along with 01211 Lock

Washers. Turn counterclockwise.

Carefully remove valve body assembly, spacers, gaskets and o-rings.

Set aside and save parts.

3 mm hex key

3. Remove motor form housing.

4. Fasten 96346 Bearing Separator (2") around 01028 Cylinder.

Place assembly in 96232 Arbor Press (#2) with pinion pointing down.

Use a Ø 1/4" drive punch to push 02373 Rotor out of 02649 Bearing.

96346 Bearing Separator

5. NOTICE: In the same way, use bearing separator, arbor press and 96213 Bearing

Removal Tool, to remove 02649 Bearing from 01732 Rear Bearing Plate.

Save parts.

96213 Bearing Removal Tool

6. Fasten 02373 Rotor in vise with aluminum or bronze jaws, with pinion pointing up.

Use an adjustable hook spanner wrench to remove 51513 Pinion Gear. Turn

counterclockwise.

Remove front bearing, plate, spacer and shims.

Motor disassembly completed.

Clean and inspect parts for wear or damage. Save and reuse good parts.

Right Angle Gear Disassembly:

1. Install 95492 Screws (5/16"-18 SHC) in two handle bosses on housing.

Fasten 51545 Housing in vise with spindle pointing up.

Use a HEAT GUN to warm housing.

Use an adjustable pin spanner wrench to remove 51551 Spindle Retainer. Turn

clockwise. Left Hand Thread.

HEAT

GUN

2. Loosen vise and remove housing.

Remove 96584 O-Ring.

Remove spindle and bevel gear assembly.

Remove 98243 Wave Spring.

3. Fasten 96346 Bearing Separator (2") under 02057 Bearing.

Place assembly in 96232 Arbor Press (#2) with threaded end of spindle pointing

down.

Use a Ø 3/16" drive punch to push spindle out of 02057 Bearing.

NOTICE: In the same way, use bearing separator and arbor press to remove

51514 Gear and 02685 Bearing.

IMPORTANT: Inspect 95913 Seals and 51550 Spindle. Replace worn parts!

NOTICE: Loctite #380 is used to retain 95913 Seals in 51551 Spindle Retainer.

Acetone can be used to soften adhesive and remove seals. SEE: Right Angle

Gear Assembly.

Right angle gear disassembly completed.

Clean and inspect all parts for wear or damage. Only reuse good parts.

Notice: To disassemble and assemble muffler and valve components, refer to

parts page or tool manual and follow exploded view instructions.

96346 Bearing Separator

Assembly Instructions - Wet, Stone Polisher

Motor Assembly:

1. Install 01010 Spacer onto rotor.

Install .003" (~0.08 mm) shim thickness into 02375 Front Bearing Plate.

Install 01007 Bearing into front bearing plate.

Install bearing and plate onto rotor.