DURKOPP ADLER 755 Operating manual
755/756
Additional Instructions
Tape feeder
All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler AG.
Copyright © Dürkopp Adler AG 2018
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Additional Instructions 755/756 - 00.0 - 10/2018 1
1 General information ................................................................... 3
2 Tape feeder ................................................................................. 4
2.1 Assembling and connecting the tape feeder ................................ 4
2.2 Setting the height of the tape feeder ............................................ 9
2.3 Aligning the tape roll holder ........................................................ 10
2.4 Inserting the reinforcement strip ................................................. 11
2.5 Setting up the tape feeder in the software.................................. 13
Table of Contents
2Additional Instructions 755/756 - 00.0 - 10/2018
General information
Additional Instructions 755/756 - 00.0 - 10/2018 3
1 General information
Components of the kit
Check whether the scope of delivery for kit 0755 590904 VES is correct
prior to installation.
Part number Quantity Designation
0755 512454 1 Toothed belt drive
0755 512444 1 Tape feeder
0217 000775 2 Tension spring
9202 002097 2 Cylinder-head bolt M4x16
9205 101877 2 Threaded pin M4x8
9202 002537 2 Cylinder-head bolt M5x35
9330 000097 6 Washer
9202 002487 4 Cylinder-head bolt M5x12
0755 512514 1 Guide carrier
0755 590914 1 Roll holder
9710 063411 2 Magnet valve
0798 120401 1 Cord clip
0755 512613 1 Suction pipe
0755 400990 1 Bracket
0755 591714 1 Dual SM card
0791 755700 EN 1 Additional Instructions
Tape feeder
4Additional Instructions 755/756 - 00.0 - 10/2018
2 Tape feeder
2.1 Assembling and connecting the tape feeder
Fig. 1: Assembling and connecting the tape feeder (1)
To assemble and connect the tape feeder:
1. Connect pneumatic hoses (1) and (2) to the tape feeder.
• blue: Cut tape (finish cutting)
• red: Cut tape (start cutting)
2. Use the connecting piece to connect pneumatic hose (3) with the
transparent hose of the tape feeder.
• gray: Press on/loosen tape
3. Remove the fabric sliding plate.
4. Swivel up the machine head.
(1) - Pneumatic hose
(2) - Pneumatic hose (3) - Pneumatic hose
①
②
③
Tape feeder
Additional Instructions 755/756 - 00.0 - 10/2018 5
Fig. 2: Assembling and connecting the tape feeder (2)
5. Insert the tape feeder.
6. Tighten screws (4) and (5).
7. Use clips to assemble pneumatic hoses (1), (2) and (3) to the plate (6).
Important
Make sure pneumatic hoses (1), (2) and (3) do NOT rest on the machine
head centering device (7) when you fold down the machine head.
8. Guide pneumatic hoses (1), (2) and (3) under the machine head and
fix them in place at the existing cables using cable ties.
(1) - Pneumatic hose
(2) - Pneumatic hose
(3) - Pneumatic hose
(4) - Screws
(5) - Screws
(6) - Plate
(7) - Machine head centering device
⑤
④
⑦
①
②
③
⑥
Tape feeder
6Additional Instructions 755/756 - 00.0 - 10/2018
Fig. 3: Assembling and connecting the tape feeder (3)
9. Assemble the guide rail (8).
10. Connect the cable (9) with the plug.
Fig. 4: Assembling and connecting the tape feeder (4)
11. Assemble the circuit board (10) and connect it to the control using
the CAN cables (12).
12. Assemble the valves (11) on top of the valve block.
(8) - Guide rail (9) - Cable
⑨
⑧
(1) - Pneumatic hose
(2) - Pneumatic hose
(3) - Pneumatic hose
(10) - Circuit board
(11) - Valves
(12) - CAN cables
⑫
⑩
①
②
③
⑪
Tape feeder
Additional Instructions 755/756 - 00.0 - 10/2018 7
13. Connect pneumatic hoses (1), (2) and (3) at the magnet valve block.
•blue(1): Y103 - 2
• red (2): Y103 - 4
• blanking plug: Y104 - 2
•gray(3): Y104 - 4
Fig. 5: Assembling and connecting the tape feeder (5)
14. Assemble the tape roll holder (14).
15. Fit the pneumatic hose (13) for the tape puller and lay it below
the machine.
16. Use cable ties and clips to fix the pneumatic hose (13) in place.
(13) - Pneumatic hose (14) - Tape roll holder
⑫
⑬
Tape feeder
8Additional Instructions 755/756 - 00.0 - 10/2018
Fig. 6: Assembling and connecting the tape feeder (6)
17. Remove the valve cover.
18. Swivel up the machine head.
19. Lay the pneumatic hose (13) through the machine arm from below.
20. Use a Y-connection (15) to connect the pneumatic hose (13) to a hose
of valve X814.
21. Place the valve cover.
22. Swivel down the machine head.
(13) - Pneumatic hose (15) - Y-connection
⑮
⑬
This manual suits for next models
1
Table of contents
Other DURKOPP ADLER Sewing Machine manuals
DURKOPP ADLER
DURKOPP ADLER 275 Series Guide
DURKOPP ADLER
DURKOPP ADLER 768 Troubleshooting guide
DURKOPP ADLER
DURKOPP ADLER 768 Operating manual
DURKOPP ADLER
DURKOPP ADLER 396-BT Series Guide
DURKOPP ADLER
DURKOPP ADLER 667 PREMIUM Operating instructions
DURKOPP ADLER
DURKOPP ADLER 367 User manual
DURKOPP ADLER
DURKOPP ADLER 556 Operation and maintenance manual
DURKOPP ADLER
DURKOPP ADLER 540-100-1 Assembly Instructions
DURKOPP ADLER
DURKOPP ADLER 610 Operating instructions
DURKOPP ADLER
DURKOPP ADLER H868 User manual
DURKOPP ADLER
DURKOPP ADLER 581 Operating manual
DURKOPP ADLER
DURKOPP ADLER 867 Operating instructions
DURKOPP ADLER
DURKOPP ADLER 911-211-10 User manual
DURKOPP ADLER
DURKOPP ADLER 745-34 - User manual
DURKOPP ADLER
DURKOPP ADLER 367 User manual
DURKOPP ADLER
DURKOPP ADLER 171 User manual
DURKOPP ADLER
DURKOPP ADLER 512-211-01 Operating instructions
DURKOPP ADLER
DURKOPP ADLER 745-34 - User manual
DURKOPP ADLER
DURKOPP ADLER LP 2971 User manual
DURKOPP ADLER
DURKOPP ADLER M-Type Premium Series Operating manual
