Drayton RF710 Instruction Manual

Digistat+1 & Digistat+1RF

Room Thermostat

Models:

RF710/22190/22192

Invensys Controls Europe

Technical Helpline: +44 (0) 845 130 7722

www.draytoncontrols.co.uk

)NSTALLATION'UIDE2&02/$5#4/.,9).34!,,!4)/./&3#22&-ODELSONLYIf you do not have the knowledge to install the SCR safely then you

must arrange for a competent electrician to install it for you. Wiring

must conform to the current IEE wiring regulations.

Prior to commencing the installation you must ensure the mains

supply is switched off.

)NSTALLATION)NSTRUCTIONS2EADALLINSTALLATIONANDCOMMISSIONINGINSTRUCTIONSBEFOREPROCEEDING$ONOTSWITCHONUNTILREADYTOCOMMISSIONThe system wiring must be able to be fully disconnected from the

mains supply by a switch incorporated in the ﬁxed wiring having a

contact separation of at least 3mm on both poles. Fused at 3A.

Receive / Alarm

Override 2

Learn

Mode

Digistat SCR

Wireless System

,OCATIONThe Digistat SCR (receiver) should be mounted in a convenient

position, close to the boiler or central heating system wiring centre.

(Care should be taken not to mount the SCR in a position where it

is surrounded by metal objects or mains voltage cable, as this may

interfere with the radio signal).

For the best performance install in an open space, at least 30cm

distance from any metal objects including wall boxes and boiler

housing.

It is recommended that the SCR is mounted on the wall nearest the

ﬁnal location of the Digistat +RF room thermostat and not less than

30cm from the boiler side panel.

7ARNING)NSTALLINGTHE3#2TOOCLOSETOTHEMETALSIDEPANELORMAINSCABLESMAYINTERFEREWITHTHERADIOSIGNAL

&IXINGMINIMUMWALLPLATECLEARANCESSHOWN1. Loosen the securing screws, remove the wallplate, and if surface

wiring is to be used, snap out the cable entry strip on the bottom

edge of the wallplate with a pair of pliers.

2. Fix the wallplate, terminals at the top, either direct onto the ﬂat

wall using wall plugs and no 6 x1” wood screws or on a ﬂush

mounting single conduit box using M3.5 x 14 screws. Minimum

wallplate clearances are shown.

3. Complete the wiring to the SCR wallplate in accordance with the

relevant diagram, to comply with current IEE wiring regulations.

4. Place the SCR onto the wallplate and tighten the securing screws.

BOILER

30cm Min

Preferred side of boiler

The range may be affected by

composition/density and number of walls

between the Digistat +RF and SCR

Radio Signal Range:

30m Typically

SCR

NL1234

50 mm

minimum

clearance

40 mm

minimum

clearance

40 mm

minimum

clearance

70 mm

minimum

clearance

NL 1 2 3

230V a.c.

Fused 3A

Common Heating

satisfied

or call for

cooling

Call for

heat

Volt free contacts

3#2WALLPLATECLEARANCES%LECTRICALThis product is double insulated and does not require an earth connection.

The SCR should be wired to the combi boiler or central heating wiring using

the correct type of cable or ﬂex. The SCR should be wired in to replace

hard wired room or programmable thermostats shown on the system or

boiler wiring diagrams. Always check other manufacturers instructions for

compatibility.

#OMBIBOILERBASICWIRINGLAYOUT:ONECONTROLBASICWIRINGLAYOUT#/--)33)/.).'4(%j7)2%,%333934%-k2&-ODELSONLYStandard for all models

IMPORTANT: MULTIZONE INSTALLATIONS ONLY

If more than one ‘wireless system’ is ﬁtted within the same property.

ie. for controlling 2 or more zones (multi-zone) it is essential that the

Digistat RF units are matched correctly to the relevant SCR. This is easily

achieved by commissioning each Digistat and SCR in turn.

1. Install (see installation instructions) and turn power on to the

SCR (receiver). If a separate programmer is ﬁtted, ensure that it is

switched on. The red LED should come on.

2. Push the ‘override’ button on the SCR once. The green LED should

also come on. Check to see if the boiler and/or motorised valve

are working.

3. To enter ‘learn’ mode push the button marked 1 followed by 2

(OVERRIDE) and hold both depressed together. The red LED

should ﬂash for 2 seconds and then go out signifying the SCR is in

learn mode. Release both buttons.

4. The red and green LED’s should both now be on.

NL123

SCR

L -

N -

Digistat + RF

Radio signals

to SCR - no wiring

Switched

230V a.c.

fused 3A,

Internal

boiler

electronics

External

controls

connections

NL123

SCR

Switched live

from wiring

centre Motorised valve

To boiler

and/or

pump

Radio signals

to SCR - no wiring

230V a.c.

fused 3A

Digistat + RF

5. Take the Digistat RF and hold it within sight of the SCR (no closer

than one metre).

6. Remove the battery cover and ﬁt the batteries.

7. The Digistat RF should now display the actual room temperature.

If the unit has been stored in a cold place, it may take time to warm

up.

8. As soon as the batteries are ﬁtted, the red LED on the SCR should

ﬂash for 7 seconds and then go out.

The green LED may be on or off depending on the room temperature

at the time of commissioning.

9. If the red LED remains on, remove the batteries on the Digistat RF,

check the battery positions are correct, and once the display has

faded, repeat steps 6 to 8.

10. Increase the ‘SET’ temperature on the Digistat RF by pressing the

+ button until a ﬂame symbol appears, in the left hand segment of

the display.

11. The red LED on the SCR should ﬂash for 7 seconds. This conﬁrms

that the radio signal is being sent and received. After 7 seconds the

red LED should go out and the green one come on.

12. Check to conﬁrm that the boiler and/or motorised valves are

working.

13. Decrease the ‘SET’ temperature on the Digistat RF by pressing the

- button until the ﬂame symbol disappears.

14. The red LED on the SCR should ﬂash for 7 seconds. After 7 seconds

both the red and green LEDs should go out. Check that the boiler

and/or motorised valve have powered down.

15. Place the Digistat RF in the chosen operating position, (see Digistat

RF location section) and repeat steps 10 to 14. Once you have

conﬁrmed the system operates correctly, ﬁt and secure the Digistat RF

to the wall (see installation instructions).

During normal operation the red LED on the SCR will ﬂash for 7 seconds

each time a radio signal is received from the Digistat RF. This will occur

approximately every 5 minutes.

The green LED on the SCR denotes a call for heat (ON).

/NCETHESYSTEMHASBEENSUCCESSFULLYCOMMISSIONEDBUTTONSANDONTHE3#2SHOULDNOTBEPRESSEDSIMULTANEOUSLYUNLESSAREPLACEMENT$IGISTAT2&OR3#2ISØTTED

,OCATIONRoom Thermostat

1.5m

Care should be taken to mount the thermostat in a position which is not

subject to direct sunlight or draughts. Preferably it should be mounted

on an inside wall about 1.5m (5ft) above the ﬂoor in a position where it

can respond to room temperature but away from the direct inﬂuence of

radiators or other appliances giving off heat.

3IGNAL3TRENGTH2&-ODELSBefore ﬁxing the Digistat+RF to the wall it is recommended to ﬁrst check

the signal strength from that location.

To do this, remove the batteries, press and hold the ‘+’ button whilst

reﬁtting the batteries, the display will show ‘rF’ which indicates that the

Digistat+RF is continuously sending an OFF signal to the SCR (receiver).

Leave the Digistat+RF in position and return to view the SCR. If the red

LED is continuously ﬂashing, this indicates a good signal. If the red LED is

not ﬂashing, this indicates a poor signal and you need to reposition the

Digistat+RF until the red LED is ﬂashing.

When the signal strength has been conﬁrmed remove the batteries to

cancel the test and follow the installation instructions.

"EFORE)NSTALLATIONIf you do not have the knowledge to install the thermostat safely then

you must arrange for a competent electrician to install it for you. Wiring

must conform to the current IEE regulations.

Prior to commencing the installation you must ensure the mains supply is

switched off.

1. Remove the front cover using a ﬂat screwdriver and separate from

back plate (Fig 1).

2. Fix the back plate directly onto the wall using suitable wall plugs and

screws or mount over existing wall box (Fig 2).

(Fig 1)

(Fig 2)

(Fig 3)

3. Replace the front cover by locating in position and pushing fully onto

the back cover (Fig 3).

Drayton

4. Remove the battery cover using a coin (Fig 4).

5. Install the 2 AA batteries provided (Fig 5).

6. Replace battery cover (ﬁg 6).

7. The Digistat +1RF is now installed and will automatically start to control the

room temperature.

Drayto

(Fig 4)

(Fig 6)

(Fig 5)

7)2).'.OT2&-ODELS

%LECTRIC(EAT

Combi Boiler

"ASIC"OILERWITH:ONE6ALVE

&!5,4$)!'./3)3!LL-ODELS)FTHEDISPLAYSHOWS%THEFOLLOWINGFAULTSCOULDHAVEOCCURRED1.Internal temperature sensor has failed.

2. Ambient temperature is outside product operating temperature range.

3"ASIC"OILER

Technical Data

$)')34!4$)')34!42&2//-5.)40OWER3UPPLY2 x AA Size, 1.5V alkaline batteries

3WITCH4YPE2ATING2ELAYVERSIONSPDT 16(2)A 230V a.c. Volt free

-INRECOMMENDEDCURRENT10mA@24V a.c. (inductive)

2ADIOFREQUENCY2&VERSION433 MHz

Radio Signal Range: 30m typically. The range may be affected by

2&6ERSIONthe composition / density and number of

walls between the Digistat RF and SCR.

Temperature Range: 5 to 30ºC

#ONTROL!CCURACY+ 0.5K @ 20ºC

!MBIENT4EMPERATUREOperating 0ºC to 40ºC /

Storage –20ºC to 55ºC

Mounting: Suitable for surface or conduit box

mounting

Wiring:

Relay: Designed for ﬁxed wiring only, to comply

with current IEE wiring regulations (BS7671).

2&No wiring required

"ALL0RESSURE4EST75ºC

0OLLUTION$EGREE2

Other manuals for RF710

This manual suits for next models

Table of contents

Other Drayton Thermostat manuals

Drayton

Drayton Lifestyle Guide

Drayton

Drayton MiStat C C110C Assembly instructions

Drayton

Drayton Wiser User manual

Drayton

Drayton 13616 User manual

Drayton

Drayton Digistat 2 User manual

Drayton

Drayton LP10RF Operation manual

Drayton

Drayton LP10RF Operation manual

Drayton

Drayton HTS3 User manual

Drayton

Drayton RF701 User manual

Drayton

Drayton Digistat+ 3 22083 Operation manual

Drayton

Drayton 13616 User manual

Drayton

Drayton MiStat P710R User manual

Drayton

Drayton Digistat+3 22083 User manual

Drayton

Drayton MiStat N110R User manual

Drayton

Drayton 22083 User manual

Drayton

Drayton LP722 User manual

Drayton

Drayton Wiser Thermostat Kit 1 User manual

Drayton

Drayton Digistat+ 2 22084 Operation manual

Drayton

Drayton RTS1 User manual

Drayton

Drayton RF701 User manual

Drayton

Drayton Digistat+2 22084 User manual

Drayton

Drayton 22083 User manual

Drayton

Drayton Digistat RF3 User manual

Drayton

Drayton RF700/22090 User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide