Dorma 8916 JT User manual

1 of 3

INS NO. Rev.

08280161 09/09

PAGE

www.dorma-usa.com 1-800-523-8483

Insert slide shoe, rubber stop and end blocks

8916/8956 JT, JTH

JAMB TRACK INSTALLATION PULL SIDE MOUNT

AND ACCESSORY PLATE BP89

WOOD FRAME

METAL FRAME

QTY

(4)

QTY

(LH DOOR)

as shown. Arrow on plate to point toward arm

(RH DOOR)

BP89 Plate applications only. Attach plate to door

attachment.

(2)

into track and attach track to frame.

RUBBER STOP

SLIDE SHOE

END BLOCK

NOTE: OUTER TWO SCREWS PASS THROUGH END

(METAL)

(WOOD)

QTY

L HINGE

BLOCKS.

END BLOCK

Assemble track and attach to frame.

(JT UNITS ONLY)

(JTH UNITS ONLY)

QTY

(1) ARM TO SLIDE SHOE

stop, hold open mechanism, and end blocks into

and tighten securely. Insert slide shoe, rubber

Attach arm to slide shoe using screw supplied

track and attach track to frame.

IMPORTANT :

END BLOCK

L HINGE

RUBBER STOP

END BLOCK

SLIDE SHOE

L HINGE

NOTE: HOLD OPEN MECHANISM AND SLIDE SHOE MUST

BE INSTALLED WITH ARROWS POINTING AWAY

FROM THE DOOR HINGES. (ARROWS ARE

STAMPED ON SLIDE SHOE & HOLD OPEN

MECHANISM)

HOLD OPEN MECHANISM

M6 HEX KEY

QTY

(4)

QTY

METAL FRAMES

QTY

(4)

WOOD FRAMES

PLATE

(LEFT HAND DOOR)(RIGHT HAND DOOR)

HINGES

CHINGESC

Attach closer to door or plate with sweep and

latch valves facing hinges.

according to appropriate template.

Determine hand of door. Prepare door and frame

(REFERENCE UNIT CARTON FOR ACCESSORIES AND

OPTIONS SUPPLIED)

LISTINGS.

IDENTIFIED IN THE INDIVIDUAL DOOR MANUFACTURER'S

DOORS, UNLESS AN ALTERNATIVE METHOD IS

WOOD OR PLASTIC FACED COMPOSITE TYPE FIRE

OF COMPONENTS TO UNREINFORCED DOORS AND TO

CAUTION: SEX NUTS ARE REQUIRED FOR ATTACHMENT

REVERSE BEVEL

RIGHT HAND DOOR

LEFT HAND DOOR

REVERSE BEVEL

RIGHT HAND LEFT HAND

INSPK NO. 08280160 Rev.09/09

08280161 2 of 3 09/09

INS NO. PAGE Rev.

Adjust according to chart.

ADJUSTER

FULL TURNS

OF SPRING

+12

FULL TURNS

OF SPRING

ADJUSTING NUT

ADJUST SPRING TENSION ACCORDING TO THE FOLLOWING CHART.

8916

8956

CLOSER

ULC LABELED UNITS ONLY

TYPE

200

200 6

SIZE

SPRING

DOOR

WEIGHT

150

125

MAX.

NON-BARRIER-FREE OPENINGS -

TYPE

8916

8956

CLOSER

INTERIOR

2'-6"

3'-6"

3'-0"

4'-0"

+12

DOOR WIDTH

SPRING

SIZE

Take an opening force reading from

the pull on the door. If required, adjust the spring tension

to meet the barrier-free requirement. Maximum number of

adjusted to meet barrier-free forces may not have sufficient

power to reliably close and latch the door.

turns counter clockwise=8. Maximum number of turns

clockwise =14. Depending on opening conditions, a door

BARRIER-FREE OPENINGS -

8916 ONLY

ADJUSTER

Adjust spring tension, if required, using a 1/4" wrench.

8956 supplied with size 6 setting.

8916 supplied with size 4 spring setting.

SPRING TENSION

CRITICAL

NOTE:

3'-6" +6 6+

250

Install main arm

onto bottom pinion. Fasten securely with pinion

With main arm parallel to door, place main arm

Rotate pinion 45° AWAY FROM HINGE edge of door.

Place wrench on bottom

pinion.

45°

screw.

* Viewed from top of door

RIGHT HAND IS A MIRROR IMAGE.

INSTALLATION SHOWN.

NOTE: RIGHT HAND DOOR

PINION SCREW

L HINGE

PINION

6mm HEX KEY

ROTATE

PINION

45°

(1)

QTY

M2.5 HEX KEY

Place the hold open

mechanism in desired

position and tighten screw.

SNAP VALVE ADJUSTMENT

WRENCH INSIDE COVER

08280161 3 of 3 09/09

INS NO. PAGE Rev.

To adjust hold open

force, turn clockwise to

increase force, and

counter clockwise to

To enable hold open,

push the white slide into

the hold open mechanism.

To disable hold open,

(HOLD OPEN UNITS ONLY)

Set hold open.

weaken force.

M2.5 HEX KEY

OFF ON

pull the white slide away

from hold open mechanism.

BACKCHECK OR DELAYED ACTION

NOTE: DELAYED ACTION IS AN OPTIONAL FEATURE.

DECREASE

control when extra time is required to pass through

Optional delayed action offers additional closing speed

the door. All valve adjustments are made with a 3/32"

CAUTION: DO NOT REMOVE VALVES.

DELAYED ACTION

BACKCHECK RANGE

SWEEP (SPEED)

INCREASE

(SPEED)

LATCH

RANGE

(TIME)

ACTION

DELAYED

hex key.

SWEEP & LATCH

POSITIONING VALVE

BACKCHECK (INTENSITY)

RANGE

LATCH

SWEEP

RANGE

DECREASE

INCREASE

should take a minimum of 1.5 seconds.

Closing time from 15° to fully closed (latch range)

generally adjusted to take a minimum of 3 seconds.

Closing time from 90° to 15° (sweep range) is

Adjust sweep and latch valves. 8

(2)

TAB

QTY

NOTE: LEFT HAND INSTALLATION SHOWN. RIGHT

HAND IS A MIRROR IMAGE.

Placecoverovercloserandfastensecurelywith

Placetabincoverslotoppositemainarm.

screwsprovided.

This manual suits for next models

Popular Door Opening System manuals by other brands

Pamex

Pamex KT-INP35 Installation instruction

Label

Label NEPTIS/LE installation manual

Cal-Royal

Cal-Royal N-F77CVR Installation instruction

Scrigno

Scrigno OPEN1000 Assembly manual

TriMark

TriMark UM 34 instructions

BFT

BFT WIND RMB 130B 200 installation manual

Alecto

Alecto ADI-250 user manual

Besam

Besam Swingmaster MP Installation, adjustment and maintenance instructions

CRL

CRL SENIOR PRIMA manual

Assa Abloy

Assa Abloy SARGENT 1431 Series instructions

GAL

GAL MOVFR Quick setup

Olide

Olide 120B installation manual

Normstahl

Normstahl IDO7 installation manual

Häfele

Häfele Finetta T 70 VF manual

AGS

AGS D-PL Instructions for fitting, operating and maintenance

Stanley

Stanley MA900ñ Installation and owner's manual

WITTUR

WITTUR Hydra Plus UD300 Instruction handbook

Alutech

Alutech TR-3019-230E-ICU Assembly and operation manual