Disc Makers ReflexFlash11 User manual

ReflexFlash

USER GUIDE 1.0

High-speed USB duplication made easy.

I. Introduction ………………………………….……….…............................ p. 2

II. System Memory Speciﬁcation ………………………………….……….... p. 2

III. Operating Environment ………………………………….……………….. p. 2

IV. Menu Overview ………………………………….………………………… p. 3

V. Functions ………………………………….……………………………….... p. 4

Synchronous v. Asynchronous ………………………………….……….…... p. 4

Synchronous Mode ………………………………….……………………….. p. 4

Asynchronous Mode ………………………………….………………..…….. p. 5

USBInfo ………………………………….……………………………….......... p. 6

System Info ………………………………….……………………………….... p. 6

Quick Erase and Full Erase ………………………………….……………..... p. 7

System Update ………………………………….……………………….……. p. 7

Start-up Menu ………………………………….……………………………… p. 7

Analyze Source ………………………………….…………………………….. p. 7

Button Beep ………………………………….………………………………... p. 8

Asyn Hold Time …………………………….……….………………………… p. 8

Ignore Size ………………………………….………………………………..... p. 8

Asynchronous …………………………….……………………………........... p. 10

Language ………………………………….…………………………….......... p. 10

Additional Information ………………………………….………………….... p. 10

I.Troubleshooting ………………………………….………………………..... p. 13

Table of Contents

User Guide 1.0 2

tReflexFlash

www.discmakers.com/techsupport

I. Introduction

The ReﬂexFlash line of USB duplicators conveniently copy portable USB storage drives without a computer.

Thanks to their advanced asynchronous duplication, each channel can independently load, unload, and copy,

so there’s no waiting or interruption. This manual will assist in the basic operation of your Reﬂex Flash unit,

showing you how fast, easy, accurate and intuitive it really is.

3-Target 7-Target 11-Target

USB Duplicator

Supported Media

USB 1.1 and

USB 2.0 Devices

USB 1.1 and

USB 2.0 Devices

USB 1.1 and

USB 2.0 Devices

System Memory 64 MB 256 MB 256 MB

*Adapter is required (not included).

II. System Memory Specification

Power

5ºC ~ 50ºC

41ºF ~ 122ºF

115V or 230V

III. Operating Environment

Working Temperature

Working Humidity 20 ~ 80%

Storage Temperature

5 ~ 95%

Storage Humidity

-20ºC ~ 85ºC

-4ºF ~ 185ºF

User Guide 1.0 3

www.discmakers.com/techsupport

Copies USB Cards or USB Drives. All contents of the

source drive will be duplicated to all target card(s)/drive(s)

DESCRIPTION

IV. Menu Overview

1. Copy

2. Compare

FUNCTION

Performs a bit-for-bit comparison between the source

drive and copied card(s) / drive(s)

3. Copy+Compare Copies the source drive, and then immediately follows with a bit-

for-bit comparison between the source and copied card(s) / drive(s)

to ensure exact duplication

4. Information

4.1 USB/SD Info Shows the basic information on the USB card(s) / USB Drive(s)

inserted, such as ﬂash type, content size, and available space

4.2 System Info Shows information of the duplicator system, such as controller model

number, system memory capacity, and software version

5. Utility

5.1 Quick Erase USB/SD Erases the index of USB Drive in the writer tray

5.2 Full Erase USB/SD Completely erases all data of USB Drive in the writer tray.

This process takes longer than Quick Erase

5.3 System Update Updates the ﬁrmware version in the system

6. Setup

6.1 Start-up Menu Allows user to select which function is shown ﬁrst when the

duplicator powers on

6.2 Analyze Source Enabled (ON) to copy data only. Disabled (OFF) to copy the entire

USB Drive

6.3 Button Beep Turns audio signal on or off when a button is pressed

6.4 Asyn Hold Time Sets the time the system waits to continue duplication jobs in

Asynchronous mode before exiting

6.5 Ignore Size Allows user to set the tolerance of capacity difference between the

source and the target

6.6 Asynchronous

6.7 Language

Allows user to enable or disable Asynchronous copy mode

Sets system language interface.

tReflexFlash

User Guide 1.0 4

www.discmakers.com/techsupport

V. Functions

1. Copy/Compare/Copy+Compare

The Reﬂex USB Duplicator can autoatically detect and support two different copy modes:

Synchronous

Asynchronous

After the system is powered on and the source drive is inserted, scroll to Copy, Compare, or

Copy+Compare and press the ENT key. The system will start to scan the source to check the

content size. If the source content is less than the system’s memory, then the system will

automatically select and start Asynchronous copying. If the source content size is larger

than the system’s memory, the system will select and start Synchronous copy.

 Synchronous v. Asynchronous:

Synchronous Copy Mode: All drives must be inserted and execute the copy or

compare function at the same time. All target drives will have the same progress

simultaneously. In this mode, the system will start the copy or compare function when the

ENT button is pressed or automatically when writer trays are all loaded.

Asynchronous Copy Mode: This mode will take effect if the data size is no larger than

256 MB (the physical buffer size of the unit) and the ﬁle format is one of the following;

FAT12, FAT16 or FAT32. All other formats will copy in Synchronous mode. The Data is

transferred to the system’s buffer and the copy process is started as soon as the target

card is plugged into a slot. Each card will be at a different point of the copy process.

The cards can be removed and another inserted into the vacant slot and that card will

begin its copy cycle.

Note: The duplicator will format the target cards/ drives to be the same as the source drive.

All data left on the target cards/ drives will be overwritten (erased) after duplication.

The contents of target cards/ drives will be exactly the same as the source drive.

How to Copy in Synchronous and Asynchronous mode

Synchronous Mode

- When source content size is larger than system memory

1. Power on the duplicator, if not already on.

2. Insert source drive.

USB(963M) 450M

0 ready

tReflexFlash

User Guide 1.0 5

www.discmakers.com/techsupport

Asynchronous Mode

- When source content size is less than system memory

1. Power on the duplicator, if not already on.

2. Scroll to select Copy, Compare, or Copy+Compare from the menu and press ENT.

3. Insert the source drive into the upper left most port designated by a rectangular white

border and press ENT. The system will start to read and copy the source content into

system memory if the content is smaller than system memory and in one of the

supported ﬁle formats.

3. Scroll to select Copy, Compare, or Copy+Compare from menu and press ENT.

4. Insert target drive(s). The LCD will show the number of target drive(s) inserted.

USB(963M) 450M

3 ready

5. After the desired number of target drive(s) are inserted, press ENT to execute the function.

Or when all writer trays are loaded with target drive(s), the system will automatically start

the function.

COPY 450M

15% 0:32 68M

Content size

Progressed size

Progressed time and percentage

Note: When the system is busy in a process, the green LED light will be blinking.

When the process is completed, the green LED will become steady. In case of error

occurrence, the red LED will turn on.

USB(58M)

Reading .... Reading source data into system memory

tReflexFlash

User Guide 1.0 6

www.discmakers.com/techsupport

4. The duplicator will immediately begin executing the function as each target drive is inserted.

Pass: 0 Working

Fail: 0 3

5. During the process, each slot’s green LED will blink continuously. CAUTION: Do NOT take

out the drive while the system is busy. Once the process is completed, the green LED light

will become steady. Once the LED light comes to a constant steady green the drive may be

removed and another inserted to continue the job.

6. The number of successful copies will be accumulated and displayed on the LCD along with

the number of failed copies and jobs still in progress.

Pass: 5

Working:

Number of copies that are completed successfully

Number of copies still in progress

Number of failed copies

Note: In Asynchronous mode, user may press the UP and DOWN buttons

to check the status and progress of each drive.

Start copying as each target drive is inserted

2. Other Functions



Information

1. USB Info (Menu Function 4.1) displays information about each drive inserted into the

duplicator, including ﬂash device type, ﬁle system format, content size, and available space.

Press UP or DOWN buttons to select and view each tray. Press ESC to exit.

[01]

FAT16

Flash device type and capacity

Available space on the device

Tray number and ﬁle system format

SD 982M

209M

2. System Info (Menu Function 4.2) displays information about the duplicator, including

controller model number, system memory capacity, and ﬁrmware version. Press ENT

to view System Info and press ESC to exit.

SD7007

256M

System memory

Model number and current ﬁrmware version

tReflexFlash

User Guide 1.0 7

www.discmakers.com/techsupport

Utility

1. Quick Erase (Menu Function 5.1) only erases the index FAT table of each drive, while

Full Erase (Menu Function 5.2) will erase the entire content of the USB Drive.

Note: Either of the Erase Functions will clear the FAT table in the SD USB Drive, making the

device unreadable on computers until it is re-formatted.

2. System Update (Menu Function 5.3): This is to update the system’s ﬁrmware version.

Place the updated, un-zipped ﬁrmware ﬁle on a USB Card or USB Drive, accordingly to

the type of duplicator. (Note: Do not put the ﬁle in a folder.) Scroll and select System

Update in the menu and press ENT. The duplicator will automatically start system updating.

When completed, power off the system for at least 5 seconds and power it back on.

The new version of ﬁrmware is now installed and the system is updated.

Setup

1. Start-up Menu

nAllows customization of the controller in order to display the menu option used most

frequently. One of the following may be chosen: Copy, Compare, Copy+Compare,

Information, Utility, and Setup.

nPress UP or DOWN buttons to scroll through the options, and press ENT

to select and exit

[Start-up Menu]

1. COPY

2. Analyze Source (Menu Function 6.2)

nWhen this function is ON, the system will automatically analyze the source drive for its

ﬁle format. If the ﬁle format is of the following FAT ﬁle system types; FAT12, FAT16,

and FAT32, the duplicator will be able recognize its structure. The duplicator will then

only copy the data content instead of copying all the sectors on the drive, even

empty space. If the system cannot recognize the source’s ﬁle format, it will copy the

entire source drive regardless of the content. For example, to copy a 2GB USB drive that

was created with FAT32 ﬁle system and containing only 50 MB of data, the duplicator

will only copy the 50MB of memory space used for actual data. The process will be much

faster than copying all the sectors on the 2GB of memory.

nWhen this function is set to OFF, the system will copy all the memory space of the source

drive, including empty spaces and formatting information. This is particularly useful if the

source drive is of an unrecognizable ﬁle format. The system will save time in analysis and

avoid possible delay or error.

tReflexFlash

User Guide 1.0 8

www.discmakers.com/techsupport

3. Button Beep (Menu Function 6.3)

nThis option will allow the user to turn on or off the audio signal when a button is pressed.

Press the UP and DOWN buttons to switch between ON and OFF. Press ENT to

select and exit.

[Button Beep]

5. Ignore Size (Menu Function 6.5)

nThis function is to set the tolerance in percentage of capacity difference between

source and target cards / drives. To ensure the FAT table of each drive is duplicated

correctly, the duplicator will require the source and all target cards/ drive to be identical

in capacity. However, it is inevitable for each drive, although marked the same capacity,

to be slightly different due to the manufacturing process. Therefore, a tolerance may

be set to avoid a system error. For example, if the source drive has a capacity of 1919MB,

with a 3% tolerance setting any target drive with a capacity of 1976MB to1861MB will be

accepted. Setting to a higher tolerance percentage will allow source ﬂash copy to targets

with different capacity’s, such as copying a 1GB source device to 2GB target device(s).

The default is set to “Don’t care,” which means the size difference is ignored and there is

no limit of source and target capacity difference.

4. Asyn Hold time (Menu Function 6.4)

nThis option allows the user to set the time the system waits when all writer trays are

unloaded before exiting the asynchronous mode. The default is set to 30 seconds.

nWhen the system is in asynchronous mode, it executes the copy or compare function for

each writer tray individually. After all target drives are removed, the system will wait

for the set amount of time for any new drive to be inserted to continue the job. If no

more drives are inserted after the hold time, the LCD will prompt:

Press ENT to exit this Asynchronous or press ESC to keep this status.

Wait too long

Exit?

nIf a source device has a smaller capacity than target devices:

1. Set the tolerance % to “Don’t care”. There will be no limit on source and target

capacity difference.

2. After the copy process is completed, the target devices will be formatted to the same

capacity as source device.

tReflexFlash

User Guide 1.0 9

www.discmakers.com/techsupport

Example: Source

1GB

Target

2GB

FAT FAT

Copy OK

nIf a source device has a bigger capacity than target devices:

1. Set the tolerance % higher or set to “Don’t care” (no limit).

2. Data stored on ﬂash devices such as USB cards and USB drives are located randomly

instead of sequentially. The success of this type of duplication depends on the data

size as well as the data location on the source device. There are three outcomes that

could be resulted from this type of copy.

Illustration 1 For source device with FAT16 or FAT32 ﬁle system whose content is located

within the capacity of target drive(s) and the content size is within the capacity of

the target drive(s):

Copy OK. The data size is less than 1GB and the data

location is within the ﬁrst 1GB of the memory space.

Source

2GB

Target

1GB

Illustration 2 For source device with FAT16 or FAT32 ﬁle system whose content is located

beyond the capacity of target card(s)/ drive(s) while the content size is still within the

capacity of the target drive(s) :

Copy Fails. Data is stored beyond the ﬁrst 1GB memory

space of the target device, even though the data size is

still smaller than 1GB.

Source

2GB

Target

1GB

tReflexFlash

This manual suits for next models

Table of contents

Other Disc Makers Disc Duplicator manuals

Disc Makers

Disc Makers ReflexMax1 User manual

Disc Makers

Disc Makers Autograph Autograph VII Installation and operation manual

Disc Makers

Disc Makers Pico MAC User manual

Disc Makers

Disc Makers Flash Duplicator User manual

Disc Makers

Disc Makers ElitePro1 Manual

Disc Makers

Disc Makers ReflexMax1 User manual

Disc Makers

Disc Makers EliteMicro Assembly instructions

Disc Makers

Disc Makers ReflexMax1 User manual

Disc Makers

Disc Makers ReflexUltra User manual

Disc Makers

Disc Makers reflex series User manual

Disc Makers

Disc Makers ElitePro User manual

Disc Makers

Disc Makers EliteMicro Assembly instructions

Disc Makers

Disc Makers Forte User manual

Disc Makers

Disc Makers ReflexMax1 User manual

Disc Makers

Disc Makers ReflexAuto 8 User manual

Disc Makers

Disc Makers ReflexUltra User manual

Disc Makers

Disc Makers ReflexUltra User manual

Disc Makers

Disc Makers MacElite 2 User manual

Disc Makers

Disc Makers reflex series User manual

Disc Makers

Disc Makers Reflex 1 User manual

Disc Makers

Disc Makers MacElite 2 User manual

Popular Disc Duplicator manuals by other brands

Riso

Riso CV Series Setting manual

MicroBoards Technology

MicroBoards Technology GX-2 user manual

Addonics Technologies

Addonics Technologies HDUS325DX user guide

Carry

Carry Pro118 user guide

CopyPro

CopyPro PowerPro II user manual

Primera

Primera Max user manual

Logicube

Logicube EchoPlus-NG user manual

Silca

Silca Delta 2000 SA operating manual

Reflex7

Reflex7 Daisy Chain Series user manual

Vinpower Digital

Vinpower Digital SharkCopier DC user manual

Codonics

Codonics Virtua E manual

Octave

Octave Copy Master II user guide

Kanguru

Kanguru U2-DVDDUPE-S user guide

StarTech.com

StarTech.com 8STSATDUP11 manual

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Service manual

Addonics Technologies

Addonics Technologies UDFH7 user guide

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 user manual

Addonics Technologies

Addonics Technologies CFASTD5 user guide