Dimplex Ropley RPL20 Instruction Manual

These instructions should be read carefully

and retained for future use. Note also the

information presented on the appliance.

Dimplex Opti-myst Freestanding Fire

Models: Ropley RPL20 / Bramdean BMD20

OPERATING

INSTRUCTION MANUAL

08/53577/0 ISSUE 4 OCN 11704

EN: This product is only suitable for well insulated rooms or occasional use. DE: Dieses Produkt ist nur für gut isolierte Bereiche oder

gelegentliche Verwendung geeignet. FR: Ce produit convient uniquement à des endroits bien isolés ou pour un usage occasionnel.

IT: Questo prodotto è adatto solo per spazi ben isolati o per uso occasionale. ES: Este producto sólo es adecuado para espacios

bien aislados o un uso ocasional. NL: Dit product is uitsluitend geschikt voor goed geïsoleerde ruimten of voor sporadisch gebruik.

PL: Produkt ten jest odpowiedni wyłącznie do dobrze odizolowanych miejsc lub do okazjonalnego użytku. NO: Dette produktet

egner seg kun for godt isolerte rom eller sporadisk bruk. RO: Acest produs este adecvat exclusiv spaţiilor bine ventilate sau utilizării

ocazionale. CZ: Tento výrobek je vhodný pouze do dobře izolovaných prostor nebo k příležitostnému použití. DK: Dette produkt

er kun egnet til velisolerede rum eller lejlighedsvis brug. PT: Este produto somente é adequado para espaços bem isolados ou

uso ocasional. SE: Denna produkt är endast avsedd för välisolerade utrymmen eller tillfällig användning. FI: Tämä tuote soveltuu

ainoastaan hyvin eristettyihin tiloihin tai satunnaiseen käyttöön. SK: Tento výrobok je vhodný len pre dobre izolované priestory

alebo na občasné použitie. SI: Ta izdelek je primeren le za dobro izolirane prostore ali za občasno uporabo. HR: Ovaj proizvod

je pogodan samo za dobro izolirane prostore ili povremenu upotrebu. HU: Ez a termék csak jól szigetelt terekhez vagy eseti

használatra alkalmas

This product complies with all the required Product Safety, Electromagnetic Compatibility and Environmental

Standards. This product is fully compliant with the LVD, EMC, RoHS and Eco Design Directives.

CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY

AND/OR DAMAGE AND MAY INVALIDATE YOUR GUARANTEE

Important Safety Advice

When using electrical appliances, basic precautions should always be followed to reduce the

risk of re, electrical shock and injury to persons, including the following:

If the appliance is damaged, check with the supplier before installation and operation.

Do not use this heater if it has been dropped.

Do not use if there are visible signs of damage to the heater.

Do not use outdoors.

Do not use in the immediate surroundings of a bath, shower or swimming pool.

Do not locate the appliance immediately below a xed socket outlet or connection box.

Use this heater on a horizontal and stable surface, or x it to the wall, as applicable.

Warning: Do not use this heater in a small rooms when they are occupied by persons not

capable of leaving the room on their own, unless constant supervision is provided.

Warning: To reduce the risk of re, keep textiles, curtains, or any other ammable material a

minimum distance of 1m from the air outlet

Warning: This heater must not be used for anything other than normal domestic household

purposes in the country where it was purchased from a recognised commercial retailer.

This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a safe way and understand

the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance

shall not be made by Children without supervision.

Children of less than 3 years should be kept away unless continuously supervised. Children

aged from 3 years and less than 8 years shall only switch on/o the appliance provided that it

has been placed or installed in its intended normal operating position and they have been given

supervision or instruction concerning use of the appliance in a safe way and understanding the

hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate

and clean the appliance or perform user maintenance.

Warning: This appliance must be earthed.

The use of an extension lead or multi-plug adaptor is not advised when connecting this product

to the mains. Connection through these devices could lead to a risk of overloading, overheating

and even re at the extension lead or adaptor due to inadequate connection quality.

This heater must be used on an ~alternating current supply (~) only and the voltage marked on

the heater must correspond to the supply voltage.

Do not use this appliance in series with a thermal control, a program controller, a timer or any

other device that switches on the heat automatically, since a re risk exists when the appliance

is accidentally covered or displaced.

DO NOT use the heater on deep pile carpets or the long hair type of rugs, or less than 750mm

(30”) away from any overhanging surface. Keep combustible materials such as drapes and

other furnishings clear from the front, sides and rear of the heater. Do not use heater to dry

your laundry.

In the event of a fault unplug the appliance. Unplug the appliance when not required for long

periods.

The appliance must be positioned so that the plug is accessible. If the supply cord is damaged

it must be replaced by the manufacturer or service agent or a similarly qualied person in order

to avoid a hazard. Keep the supply cord away from the front of the appliance.

Caution: Some parts of this product can become very hot and cause burns. Particular

attention has to be given where children and vulnerable people are present. This instruction

can be found at www.dimplex.co.uk

with electronic room temperature control.

The re incorporates a ame eect, which can be used with or without heating, so that the

comforting eect may be enjoyed at any time of the year.

A fan heater can provide heating in cold weather. A distance of 1 metre (3 feet) must be maintained

between the front of the heater and any surrounding furniture, overhanging curtains or other

obstructions.

Always ensure that the appliance is sitting on a level surface.

Before connecting the appliance, check that the supply voltage is the same as that stated on the

appliance.

Only use ltered water in this appliance.

Once installed, never move this appliance or lay it on its back, without draining the water from

sump and water tank. The water tank, sump, sump lid, tank cap and air lters must be cleaned

once every 2 weeks, particularly in hard water areas. If you intend not using the appliance for

longer than 2 weeks, drain the water from sump and water tank and dry the sump.

Please note: Used in an environment where background noise is very low, it may be possible to

hear a sound which is related to the operation of the ame eect. This is normal and should not

be a cause for concern.

The sump and the water tank in this product are treated with a biocidal product, Silver Biocide

in order to control harmful or unwanted organisms. This conforms with the latest relevant ISO

standard. Do not drink the water from the sump or from the water tank(s)

Technical Information

Model No: RPL20, BMD20

Thank you for choosing a Dimplex electric re

General Information

Dimplex Opti-myst Freestanding Fire

Models: Ropley RPL20 / Bramdean BMD20

Heat Output 230V 240V

Nominal Heat Output PNom 1.8 2.0 kW

Minimum Heat Output Pmin 0.9 1.0 kW

Maximum Continuous Heat Output Pmax 1.8 2.0 kW

Auxiliary Electricity Consumption

In Standby Mode PNom 0.45 0.48 W

Warning: In order to avoid overheating, do not cover the appliance. Do not place material or

garments on the appliance, or obstruct the air circulation around the appliance, for instance by

curtains or furniture, as this could cause overheating and a re risk.

The appliance carries a DO NOT COVER warning

Warning: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this

appliance must not be supplied through an external switching device, such as a timer, or

connected to a circuit that is regularly switched on and o by the utility.

This heater must be used on an AC ~ supply only and the voltage marked on the heater must

correspond to the supply voltage. Before switching on, please read the safety warnings and

operating instructions. Please retain this user’s guide for future reference

Ensure that all packing items are removed (read any warning labels carefully). Retain all packing

for possible future use e.g. in the event of moving or returning the appliance to your supplier.

To install the appliance;

1. Clean the area where the re will be installed.

2. Hold the re by the sides of surround and gently manoeuvre into position.

3. Plug the re into a 13amp/240 volt outlet. Ensure that the supply cable is not trapped under

the re such that it might cause it to be damaged.

4. Ensure that the draft excluder (rubber strip) is tted to the channel on the base of the product.

Connecting the Transducer

1. Gently lift out the fuelbed and carefully set aside. (Fig 3)

2. Remove the water tank by lifting upwards and outwards. (Fig 4)

3. Remove the nozzle by unclipping and lifting upwards and outwards. (Fig 5)

4. The transducer will be inside the sump. Remove from its bag.

5. Place the Transducer unit into the sump and make the connection.

6. Locate the tab on the Transducer unit into the moulded recess in the base of the sump (Fig 6)

7. Ensure that the cable does not obstruct the Transducer disc. To prevent the cable becoming

pinched between the nozzle and the sump, place the cable in the slot in the wall of the sump.

(Fig 7)

Filling the Water Tank

1. Gently lift out the fuelbed and carefully set aside.

2. Remove the water tank by lifting upwards and outwards.

3. Place the water tank in sink and remove cap, Anti-clockwise to open. (Fig 8)

3. Fill tank with ltered tap water only. This is necessary to prolong the life of the ame and

smoke producing unit. The water should be ltered through a conventional domestic water

lter unit and the lter should be replaced regularly.

6. Screw the cap back on, do not over tighten.

7. Return the tank to the sump, with the tank cap facing down

8. Gently place the fuelbed back into position.

When the water tank is empty, the ame and smoke eect shuts o, you will hear 2 audible beeps

and the digital display will display

Installation Instructions

WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN

INJURY AND/OR DAMAGE.

Manual Controls

The manual controls are located beneath the hinged ap at the top of the product. (Fig 2)

is the on/standby button. Press it once to turn on the product. Press it again to turn o the

product. When turned on a ‘beep’ will sound and the digital display will show followed by

the current room temperature. The display will then turn o. The fuelbed will light up. Be careful

not to look directly into the fuelbed as the LED lights are very bright. It will take a approximatly

45 seconds before the ame eect starts.

is the Mode button.

Press it once and you will be in the options. The display will show the current setting. Using

the and buttons you can turn the heat on at the LOW or HIGH setting and turn the heat

OFF. You will hear two ‘beeps’ for LOW heat setting, three ‘beeps’ for HIGH heat setting and one

‘beep’ when the heat is turned o.

Press it a second time and you will be in the temperature set mode . The display will show

the current room temperature and then the set point temperature. Using the and buttons

you can adjust the set point temperature up and down. Note: if the set point temperature is below

the room temperature the heat function will not operate. The temperature range is from 15-35°C

Press it a third time and you will be in the Fire mode. The display will show followed by the

current re eect setting. There are six re settings. Using the and buttons you can turn up

and down the re setting.

Remote control

The remote control is supplied with a battery already in place. Simply pull on the clear plastic tab

on the back of the remote control to enable the battery.

• is the on/standby button. Press it once to turn on the product. Press it again to turn o

the product. When turned on you will hear on ‘beep’ and the digital display will show

followed by displaying the current room temperature. The display will then turn o. The main

LED lights will activate. Be careful not to look directly into the LED’s. These are very bright.

Although the main lights operate immediately it will take a further 45 seconds before the ame

eect starts.

• Press once to activate heat setting. Press it again to activate heat setting.

If you continue to press this button you will cycle through the LOW and HIGH heat settings.

You will heat two ‘beeps’ for LOW heat setting and three ‘beeps’ for HIGH heat setting.

• Press once to turn o the heat. You will hear one ‘beep’

Operating The Product

Press M Display Function Press + or -

Once Controls the fan

heater O Low High

Twice Thermostat From 15 °C To 35 °C

Three times Flame intensity From F1 (low) To F6 (high)

• Press the button to display the current room temperature followed by the current set point

temperature

• Press the and buttons to adjust your set point temperature. Note: if the set pointtemperature

is below the room temperature the heat function will no operate. The temperature range is from

15 - 35°C

• Press to increase the setting.

• Press to decrease the setting.

Setting the Thermostat

Plug in the product and press to turn it on. Press the button twice and be in the temperature

set mode . The current room temperature will be displayed (e.g. r23C) followed by the current

set point room temperature (-26C). Press the and buttons to select your set point room

temperature. Allow the display to turn o. Press the button once to be in the Heat option. Press

the and buttons to select either or heat output. The heater will turn on when your

set point room temperature is higher that the room temperature.

Thermal safety cut-out

A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating.

This can happen if the heat outlet was restricted in any way. If the cut-out operates, unplug the

heater from the socket outlet and allow approximately 10 minutes before reconnecting. Before

switching the heater back on remove any obstruction that may be restricting the heat outlet, then

continue normal operation.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this

appliance must not be supplied through an external switching device, such as a timer, or connected

to a switch that is regularly switched on and o by the utility.

Getting the desired ﬂame eect

1. Using the manual controls or the remote control choose a setting between F1 and F6. F1

being the lowest setting and F6 being the highest setting.

2. Generally the ames appear more realistic when the ame control is turned down.

3. Give the ame generator time to react to changes you may make.

4. The re will use less water if the ame eect is set to a lower level.

5. Do not tilt or move the re while there is water in the tank or sump.

6. Make sure that the re is on a level oor.

General tips

Only use ltered tap water in this appliance.

Always ensure that the appliance is sitting on a level surface.

If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and

water tank.

Once installed, never move this appliance or lay on its back, without draining the water from

sump and water tank.

Cleaning

Warning – Always press to turn o the product and disconnect the product from the power

supply before cleaning the re. Leave the appliance for 10 minutes to allow the product to cool

down

Maintenance

We recommend cleaning the following components once every 2 weeks,

particularly in hard water areas:

Water Tank, Sump, Nozzle, Tank cap and seal, Air lter.

For general cleaning use a soft clean duster – never use abrasive cleaners.

To remove any accumulation of dust or u, the soft brush attachment of a vacuum cleaner

should occasionally be used to clean the outlet grille of the fan heater.

Water Tank

1. Remove water tank, as described earlier, put into sink and empty water.

2. Using the supplied brush gently rub the inside surfaces of the cap paying particular attention

to the rubber ring in the outer groove and the center rubber seal.

3. Put a small quantity of washing up liquid into the tank, ret the cap and shake well, rinse out

until all traces of washing up liquid are gone.

4. Rell with ltered tap water only, replace the cap, do not over tighten.

Sump

Press to put the product into standby

Gently lift out the fuelbed and place carefully on the ground.

Remove the water tank by lifting upwards.

Remove the sump lid, this allows the sump to be lifted completely from its location. (Fig 5)

Gently lift up the sump, taking care to keep level so as not to spill any water. Sit the assembly in

the sink.

Carefully tilt so that the liquid drains out of the sump.

Put a small amount of washing up liquid into the sump, and using the supplied brush, gently

clean all surfaces including the metal disc (Fig 9)

When cleaned, thoroughly rinse the sump with clean water.

Clean the outlet surface of the sump lid with the brush and ush out thoroughly with water.

Reverse the above steps to reassemble.

Air Filter

1. Press on the remote control or on the product to turn it o

2. Gently lift o the fuelbed and set aside

3. Remove the tank and place in a sink with the cap facing upwards.

4. Gently slide up the air lter (Fig. 10)

5. Gently rinse with water in the sink and dry with fabric towel before returning.

6. Replace the lter making sure that the course black lter is in contact with the plastic holder.

7. Replace the tank.

8. Replace the fuelbed.

9. Press to turn on the product

General Cleaning and Maintenance

The outside can be cleaned by wiping it over with a soft damp cloth and then dried. Do not use

abrasive cleaning powders or furniture polish, as this can damage the surface nish.

CAUTION: Assembly, installation and repair of this heater must be carried out by Dimplex or its

authorised agent.

CAUTION: We recommend that you arrange for this heater to be checked annually for safety by

a qualied electrician.

Additional Information

After Sales Service

Your product is guaranteed for one year from the date of purchase. Within this period, we undertake

to repair or exchange this product free of charge (excluding transducer discs & subject to availability)

provided it has been installed and operated in accordance with these instructions. Your rights

under this guarantee are additional to your statutory rights, which in turn are not aected by this

guarantee.

The transducer is a consumable item and may need to be replaced through time, depending on its

usage. Replacement transducers can be purchased from our website http://spares.dimplex.co.uk.

The transducer has a 12 month warranty period.

CAUTION: Do not use if the heater’s mains power lead is damaged. Such use may cause a hazard.

If damaged, the mains power lead must be replaced by the manufacturer or its authorised dealer.

Should you require after sales information or assistance with this product please go to www.

dimplex.co.uk and select “Customer Support” or ring our help desk on 0344 879 3588 (UK) or 01

8428 222 (R. O. I.). Spare parts are also available on the web site. Please retain your receipt as

proof of purchase.

Recycling

At the end of the electrical products useful life it should not be disposed of with household

waste. Please recycle where facilities exist. Check with your Local Authority or retailer for

recycling advice in your area.

Patent / Patent Application

Products within the Optimyst range are protected by one or more of the following patents and

patent applications:

Great Britain GB2460259B, GB2475794B, GB2418014, EP2029941, GB2436212, GB2402206B

United States US8413358, US8136276, US7967690, US8574086

Russia RU2434181

European EP2029941, EP2315976, EP1787063 (A1), EP2388527

China CN101883953A, CN102105746A, CN101057105 (A), CN101438104

Australia AU2009248743A1, AU2007224634

Canada CA2725214, CA2579444, CA2645939

South Africa ZA2008/08702

Mexico MX2008011712

South Korea KR101364191

Japan JP5281417, JP5496291

Brazil BRP10708894

India 4122/KOLNP/2008

New Zealand NZ571900

Troubleshooting

Symptom Cause Corrective Action

The ame eect

will not start.

Mains plug is not plugged in. Check plug is connected to wall

socket correctly.

Low water level. Check that the water tank is full and

there is water in the sump.

The Transducer Unit is not sitting

correctly in the sump

Ensure the Transducer in sitting down

into the moulded recess in the sump

The ame eect

is too low.

Flame eect is set too low.

Increase level of ame by

pressing three times to get

you into mode.

Press to increase the ame setting

The Metal Disc in the transducer

might be dirty

Clean the Metal Disc with soft brush

supplied. (Fig 9) See ‘Maintenance.’

for a step by step procedure.

The wire from the Transducer Unit is

sitting over the metal disc

Direct the wire to the back of the

sump and make sure it sits into the

side slot exiting the sump.

Unpleasant smell

when unit is used.

Dirty or stale water. Clean the unit as described under

maintenance.

Using unltered tap water. Use only ltered tap water.

Fig. 1a

123

670 mm

566 mm

217 mm

Fig. 1bFig. 2

This manual suits for next models

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex MULTIFIRE DF3015 User manual

Dimplex

Dimplex IN-STUD V1525BT User manual

Dimplex

Dimplex DWF120330B User manual

Dimplex

Dimplex DLW1500B12 User manual

Dimplex

Dimplex STRAUSS STS20 User manual

Dimplex

Dimplex ELGAR EGR20 User manual

Dimplex

Dimplex DFP15-1134NG User manual

Dimplex

Dimplex BF362SD User manual

Dimplex

Dimplex BF362SD User manual

Dimplex

Dimplex VCX1525 User manual

Dimplex

Dimplex ORVIETO MCFP15O User manual

Dimplex

Dimplex BF36 Series User manual

Dimplex

Dimplex PF2325 User manual

Dimplex

Dimplex WYN20 User manual

Dimplex

Dimplex RITZ20W User manual

Dimplex

Dimplex DWF-1326 User manual

Dimplex

Dimplex DF2000L User manual

Dimplex

Dimplex EF2570G User manual

Dimplex

Dimplex SP320 User manual

Dimplex

Dimplex BLF50 User manual

Dimplex

Dimplex DF2622 User manual

Dimplex

Dimplex LEE User manual

Dimplex

Dimplex CASTILLO CS3550 User manual

Dimplex

Dimplex Americana AMR20R User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual