Dimplex Saletto LPP050E User manual

08/80070/0 ISSUE: 2 Series: A

These instructions should be read carefully

and retained for future use. Note also the

information presented on the appliance.

INSTRUCTION MANUAL

Installation and Operating

Dimplex Saletto (LPPE)

Models: LPP050E / LPP075E / LPP100E / LPP150E

IMPORTANT

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR

FUTURE REFERENCE. Note also the information presented on the appliance

CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/

OR DAMAGE AND MAY INVALIDATE YOUR GUARANTEE

IMPORTANT SAFETY ADVICE

When using electrical heaters, basic precautions should always be followed to reduce

the risk of ﬁre, electrical shock, and injury to persons, including the following:

IMPORTANT: The wall bracket supplied with the heater must be used.

IMPORTANT: All packaging should be disposed of in an appropriate manner.

OVERHEATING WARNING

WARNING:In order to avoid overheating, do not cover or obstruct the heater. Do not

place material or garments on the heater, or obstruct the air circulation around the heater,

for instance by curtains or furniture, as this could cause overheating and a ﬁre risk. NEVER

cover or obstruct in any way the heat outlet slots at the top of the heater or the air inlet

slots in the base of the heater.

WARNING:

THE SURFACES ON THIS HEATER CAN BE HOT. The heater carries a

warning ‘DO NOT COVER’ to alert the user to the risk of ﬁre that exists if the heater is

accidentally covered. DO NOT place combustible items through the heater grille.

CAUTION:Some parts of this product can become very hot and cause burns. Particular

attention has to be given where children and vulnerable people are present.

For your safety this heater is ﬁtted with a thermal cut-out. In the event that the

product overheats for some reason, the cut-out prevents excessive temperatures on

the product by cutting the power to the heater. Once the heater has cooled down,

it will reset automatically, it will continue to cycle on and o automatically until the

reason for overheating is removed. The display screen may ﬂash red to indicate the

product has overheated. To reset the display, remove the obstruction and hold Enter

for 10 seconds.

SUITABLE APPLICATIONS

WARNING: This heater is suitable for normal domestic household purposes and

should not be used in any other type of environment. This product should only be

used in the country where it was purchased from by a recognised commercial retailer.

Do not use outdoors.

SERVICING AND REPAIRS

WARNING

Servicing and product repairs should only be undertaken by the

manufacturers approved service agent or a similarly trained or qualiﬁed person, using

only exact manufacturer approved spare parts.

PLEASE NOTE: Household dust, lit cigarettes, candles and oil burners, combined with

the convection eect of electric heaters can cause signiﬁcant soot deposits to build

up on the surface directly above and to the sides of the heater. This is not a fault of the

heater. Extensive burning of candles or smoking in the operating environment of this

product can produce heavy discolouration within a few months of use.

OPERATING WARNINGS

IMPORTANT: Remember to observe all safety warnings and precautions when

operating the heater on the automatic or timer modes, either attended or unattended

since a ﬁre risk exists when the heater is accidentally covered or displaced.

CAUTION: Do not use if the heater’s mains power lead is damaged. If the supply cord

is damaged it must be replaced by the installer or an approved Dimplex service partner.

ELECTRICAL INSTALLATION

WARNING: The electrical installation of this heater must be carried out by a

suitably qualiﬁed or trained electrician, and be in strict accordance with the

current wiring Regulations BS 7671. The supply must be connected via a switched

fused spur with a fuse rated suitably for the appliances ﬂex. Failure to follow these

instructions will mean that the manufacturer’s instructions have not been adhered to.

THERE ARE NO EXCEPTIONS.

WARNING: Minimum clearances and IP zone requirements must be adhered to in

accordance with the current wiring regulations.

The wires in this mains lead are coloured in accordance with the following code:

GREEN AND YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

• This heater must be earthed

• Not suitable for connection via a plug top

• Do not locate the heater immediately below a ﬁxed electrical point i.e. socket outlet.

The heater is ﬁtted with a length of ﬂexible cable type H05VV-F size 3 x 1.0mm² for 500W

to 2kW models for connection to the ﬁxed wiring of the premises through a suitable

connection box positioned adjacent to the heater. A means for disconnection must be

incorporated in the ﬁxed wiring of the premises in accordance with the current wiring

regulations. The supply circuit to the heater must incorporate a double pole isolating

switch having a contact separation of at least 3mm. Products that are supplied without

a plug are for installation into the ﬁxed wiring of the property, via a suitable double pole

switched fused spur with a fuse rated suitably for the appliances ﬂex. Typical fuse ratings

for 230V equipment - Up to 700W = 3A, over 700W = 13A.

In installation the supply cord must be cut to the appropriate length for the electrical

connection point. Excess cable should not be inserted and stored behind the heater.

WARNING: This heater must not be connected to the electricity supply via an external

switching device (such as a timer) or a circuit that is regularly switched on and o by

the utility supplier. Failure to follow this warning could result in the heater’s thermal

cut-o being inadvertently reset and could create a ﬁre hazard. Cables/ﬂexes that are

supplied pre-ﬁtted to the product must NOT be extended.

CHILD SAFETY

WARNING

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of appliance by a

person responsible for their safety.

This appliance can be used by children from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance. Children

shall not play with the appliance. Cleaning and user maintenance shall not be made by

children without supervision. Children of less than 3 years should be kept away unless

continuously supervised.

Children aged from 3 years and less than 8 years shall only switch on/o the appliance

provided that it has been placed or installed in its intended normal operating position

and they have been given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children aged from 3 years and less

than 8 years shall not regulate and clean the appliance or perform user maintenance.

This product contains a replaceable battery.

WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN.

WARNING: Packaging should be disposed o responsibly as the EPS could be a

potential choking hazard for children

Model Identiﬁer(s): LPP

050E

LPP

075E

LPP

100E

LPP

150E

Nominal heat output Pnom 0.5 kW 0.75 kW 1 kW 1.5 kW

Height (mm) 235 235 235 235

Width (mm) 746 746 877 1142

Depth (mm) 100 100 100 100

Minimum heat

output (indicative) Pmin N.A. N.A. N.A. N.A.

Maximum continuous

heat output Pmax,c 0.5 0.75 1 1.5

Auxiliary electricity Consumption

At nominal heat output elmax 0.00 0.00 0.00 0.00

At minimum heat output elmin 0.00 0.00 0.00 0.00

In standby mode elSB <0.0005 <0.0005 <0.0005 <0.0005

With open window detection Yes

With adaptive start control Yes

Type of heat output/ room temperature control

With electronic room temperature control Yes

Electronic room temperature control plus week timer Yes

With open window detection Yes

With adaptive start control Yes

This product complies with Lot20 of the Energy Eciency Directive (2015/1188).

Energy Related Product Directive

Technical Details

All Models

Controls

Digitally controlled, Electronic Thermostat accurate to (±0.2oC)

Timer modes:

7 Day Programmable User Timer, Out All Day, Home All Day, Holiday

Continuous heat modes:

Eco, Manual, Frost Protect, Setback, Runback, O

Controller UI

• Graphical display with RGB backlight

• Capacitive buttons with audio feedback

• User replaceable battery (Coin-Type)

Controller Functions

• Open window detection, Adaptive-start

• Advance time period

• Adjustable max setpoint range (7-32°C)

• Bluetooth for software updates

• Child Lock & Landlord Lock (PIN-based)

Construction

• Durable epoxy-polyester powder coated steel casing with louvered

upward facing grille

• Advanced controls with capacitive sense technology for total

ﬂexibility of heating

Finish / Colour

Metal Chassis, Air Outlet Grille & Control Moulding

Trac White (RAL 9016)

Element Compact, ﬁnned, mineral ﬁlled sheathed element

Installation • Wall bracket

Safety

• Thermal cut-out. Auto reset type

• Overheat detection

• Advance time period

IP Rating IP24

Battery

3.3V coin cell battery to backup real time clock. Battery life >5 years.

Supply

1.3 metres ﬁtted, 3 core for fused spur installation, 1/N/PE ~230-240 V,

50Hz Class I, with earth wire

Approvals CE, BEAB

Warranty 2 years

Country of Origin United Kingdom

Manufacturer Glen Dimplex Heating & Ventilation (GDC Group Ltd.)

WARNING:

This product is heavy and care

should be taken in installation

Please read the instructions closely before ﬁrst using the product, there is also a

quick-start guide on page 8 if you need a reminder of how to use the basic functions

in the future. The heater is designed for wall mounting using the wall bracket supplied.

It should only be operated when in the upright position as shown - see Fig.3 and Fig.4.

All models are splash proof to IP24. Before connecting the heater check that the supply

voltage is the same as that stated on the heater.

MODEL A B C D E

LPP050E 672mm 150mm 746mm 235mm 100mm

LPP075E 672mm 150mm 746mm 235mm 100mm

LPP100E 803mm 150mm 877mm 235mm 100mm

LPP150E 1068mm 150mm 1142mm 235mm 100mm

General Information

Wall Mounting Instructions

IMPORTANT - The wall bracket

supplied with the heater must

be used and the heater must

be installed in the correct

orientation. The ﬁxings should

be used to secure the bracket to

the particular wall on which the

heater will be installed. The heater

should be positioned observing

the minimum clearances stated

around the heater - see Fig. 2,

Fig. 3 and Fig. 4.

‘A’

250mm

‘B’

Minimum

mounting

clearance

Minimum mounting clearance

Fig. 2

To mount the heater to the wall:

1. Remove wall mounting bracket from the back of the heater by depressing the spring

latch at the side of each bracket - see Fig.2.

2. Fix the wall bracket securely to the wall through the four screw holes. Ensure only

screw ﬁttings suitable for the particular wall type are used.

3. Present the heater to the wall bracket and engage bottom slots in the back with

bracket hooks.

4. Press the top of the heater into locked position and ensure the clips on the top are

engaged.

WARNING:

This product is heavy and care

should be taken in installation

‘C’ 150mm

(min)

150mm

(min)

150mm

(min)

‘D’

Minimum mounting clearance

300mm

170mm*

(min) ‘E’

Shelf / Obstruction

*The minimum distance

from the shelf should be

170 minimum if the shelf

is wider than 50mm, or

50 minimum if the shelf

is 50mm or less.

Minimum front

clearance

Please note correct product

orientation is with controller

facing top right side only

150mm

(min)

Fig. 3

Fig. 4

How Does the Heater Control Work?

The controller allows you to choose when you want heat and at what temperature.

When using a timer mode (see below), Comfort On will display on the home screen to

tell you when the heater is maintaining the temperature displayed. Comfort O will

display when the heater is outside of a timed heating period. When Manual, Eco or

Frost modes are being used the heater will always maintain the temperature shown

on the home screen.

Set the Time

To set the date and time on the heater, press Menu, then press Enter with Time / Date

highlighted. Press or until the correct value is shown, then press Enter to conﬁrm

and move onto the next value. Repeat until all details are correct, and Set displays,

then press Back. The time is automatically adjusted in spring and autumn between

Greenwich Mean Time (GMT) and British Summer Time (BST).

Set the Temperature

The temperature shown on the display is the room temperature set point (target

room temperature). This is the temperature that the heater will maintain during the

heating periods. If the room temperature is above this temperature then the heater

will not operate. The heater leaves the factory with this temperature set at 21°C which

represents a typical, comfortable room temperature. If you require a dierent room

temperature, use either or until the display shows the temperature you require.

Timer Modes

Your Dimplex LPPE Panel

comes pre-programmed

with four timer modes. These

modes deﬁne the periods

when the heater will operate

in Comfort On mode. The four

modes are shown in Fig.5

This guide is for quick reference only.

Please refer to the operating section on Page 12 for further information.

Timer Mode Description

User timer Customise times in four periods

Out All Day 6 hours heating per day in two

periods

Home All Day 13 hours heating per day in one

period

Holiday

Set the temperature and number

of days for which you are on

holiday

Quick Start Guide

Which Timer Mode is Best for Me?

The heater leaves the factory set in Out All Day mode. If you are out during the day

and only require heat in the mornings and evenings then this mode will likely suit your

lifestyle.

If you are in during the day then you should select the Home All Day mode which is

a single heating period.

Fig. 5

This manual suits for next models

Table of contents

Other Dimplex Heater manuals

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide