DFI VP101-BT User manual

VP101-BT Installation Guide

Package Contents

DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the

installation process, please refer to the user's manual.

www.d.com

Note:

The CD that came with the system contains an autorun screen to install drivers, utilities,

and software applications required to enhance the performance of the system and a user's

manual for your reference. Insert the CD into a CD-ROM drive. The autorun screen will ap-

pear. If after inserting the CD, “Autorun” did not automatically start, please go directly to

the root directory of the CD and double-click “Setup”. Please install all required drivers.

•

1 VP101-BT system unit

• 6

Mounting screws for Mini PCIe module

•

1 Quick Installation Guide

•

1 Disk includes:

- Drivers / Manual

Panel

Bottom View

Top View

Note:

You can choose to wire the COM 4 port to be a CANbus (Controller Area Network)

interface instead.

VGA

USB 2.0

LAN 2

Line-out

LAN 1 MIC-in

VCC/ACC/GND

(Connects to car battery)

COM 3

(RS232/RS422/RS485)

COM 5

(RS232)

Antenna

hole

COM 1/2

(RS232/RS422/RS485)

HDMI

COM 4/ 8-bit DIO

CANbus*

USB 3.0

Reset switch/

Status LED

Power button

4. After removing the mounting screws, lift the bottom side of the chassis

cover to open the system. The Mini PCIe and the micro SD slots will be

readily accessible.

Removing the Chassis Cover

Please observe the following guidelines and follow the procedure to open the system.

1. Make sure the system and all other peripheral devices connected to it have

been powered off.

2. Disconnect all power cords and cables.

3. The 12 mounting screws on the bottom and two sides of the system are used

to secure the cover to the chassis. Remove these screws and then put them in

a safe place for later use.

Chassis screw

Power board

micro SD

Mini PCIe slots

Installing a Mini PCIe Card

The system board is equipped with 3 Mini PCIe slots: two full-size and one half-

size slots. Here we will demonstrate the installation of a half-size Mini PCIe card

(

PCIe/USB/LPC signals

) for WiFi connection.

1. Grasp the Mini PCIe card by its edges and align the notch in the connector of

the card with the notch in the connector on the system board.

2. Push the Mini PCIe card down and use the provided mounting screws to se-

cure the card on the system board.

Note:

The system also has two additional full-size Mini PCIe slots that use PCIe (PCIe/

USB/3G/GPRS/CANbus signals) and mSATA (SATA signals) interfaces.

Mounting screw

Installing a SATA Drive

The system can accomondate one SATA drive. Please use the following procedure

to install a SATA drive into the system.

2. Install the SATA drive on the HDD bracket. Place the HDD bracket back to the

system and secure the drive in place with the provided mounting screws.

1. SATA HDD bay is located under the power board. Please remove the

power board rst to uninstall the HDD bracket.

SATA connectors

on the board

SATA connectors

SATA

Mounting screws

Power board

Mounting screws

SATA bracket

Mounting screws

The wall mount kit includes the following:

• 2 wall mount brackets

• Bracket screws

1. Select a place on the wall where you will mount the system.

2. Use the provided mounting screws to attach “wall mount bracket 1” to

the wall.

Mounting Options

Wall mount

Wall mount bracket 1 Wall mount bracket 2

Wall mount bracket 1

Mounting screw

3. Attach the other bracket (wall mount bracket 2) to the rear of the

system.

4. Slide the system to "wall mount bracket 1" to attach the two brackets with the

hooks. Then tighten the screw to secure the assembly in place.

Screw

Wall mount bracket 2

Mounting screw

Hooks

1. Select a place on the panel (or wall) where you will mount the system.

2. Cut out a shape on the panel that corresponds to the system’s rear di-

mensions (272mm x 169mm) and ensure that the system can be tted

into the panel properly.

3. Insert the system from the outside surface of the panel into the mount-

ing hole until it is properly tted against the panel.

4. Position the mounting clamps along the rear edges of the system and

insert them into the slits around the system.

www.d.com

Panel mount

The panel mounting kit includes the following:

• 6 mounting clamps

132.20

210.50

Panel

Mounting hole

272

169

5. The rst and second clamps must be positioned and secured diagonally prior

to mounting the rest of the clamps. Tighten the clamp’s screw using an electric

screwdriver by pressing the white plastic cap onto the back of the panel. The

illustration below shows that all clamps are properly mounted.

272

169

Slit for mounting the clamp

Mounting clamp

White plastic cap

Board Layout and Jumper Settings

TOP BOTTOM

LAN 1

LAN 2

DDR3L

Mini PCIe with SIM

COM 4

1210

JP22 1

(JP20)

(JP18)

(JP17)

(JP21)

1 3

1210

COM 2

USB 0

USB 3.0

HDMI

Reset

Power

DC-in

USB 2

USB 7

USB 1

USB 6

COM 3

Battery

Buzzer

Chassis

Intrusion

Clear CMOS

Data (JP24)

SPI

Flash

BIOS

eMMC

(optional)

iTE

IT8528E

Mini PCIe with LPC mSATA

MicroSD

(optional)

System Fan

USB 0

Power

Select

(JP5)

1 1

USB 1-2

Power Select (JP6)

USB 5-7 Power

Select (JP7)

(JP25)

USB 2.0

(JP17)

(JP20)

COM 4/DIO Select (JP22, JP21)

Digital I/O 0-3 Output State

Digital I/O Power Select

Auto

Power-on

Select

(JP18)

Digital I/O 4-7 Output State

VGA

DC-in

from

Power board

DDR3L

Intel Atom

E3800 Series

Intel

WGI210AT

Nuvoton

NCT6106D

ASMedia

ASM1442

Intel

WGI210AT

SMSC

USB4604

SIM Card

NXP

PTN3460

Standby

Power LED

www.d.com

USB Power Select: 0 (JP5), 1-2

(JP6), 5-7 (JP7)

+5V_standby (default) 1-2 On

+5V 2-3 On

Clear CMOS Data JP24

Normal (default) 1-2 On

Clear CMOS Data 2-3 On

Auto Power-on Select JP25

Power-on via power button 1-2 On

Power-on via AC power

(default)

2-3 On

Note:

You cannot use COM 4 and DIO at the same

time. Please adjust JP21 and JP22 together.

Digital I/O Output State JP18 (DIO 4-7)

JP20 (DIO 0-3)

GND (default) 1-2 On

+5V or +5V_standby 2-3 On

Digital I/O Power Select JP17

+5V_standby 1-2 On

+5V (default) 2-3 On

COM 4/DIO Select JP21, JP22

C O M 4 ( d e f a u l t ) 1-2, 4-5

7-8, 10-11 On

DIO 2-3, 5-6

8-9, 11-12 On

Other manuals for VP101-BT

Table of contents

Popular Touch Panel manuals by other brands

FlowLine

FlowLine Data loop quick start

ALPEX

ALPEX AEx-8 P Series user manual

Ltech

Ltech E5S manual

Harman

Harman AMX MODERO S MSD-701-L2 quick start guide

Acnodes

Acnodes PC 1150 installation guide

AIS

AIS IP10IA99 series user guide

IBASE Technology

IBASE Technology ASTUT-152-RE1S user manual

YASKAWA

YASKAWA TP 610C manual

B&R

B&R Power Panel C Series user manual

Beijer Electronics

Beijer Electronics X2 control Hardware and installation manual

AXIOMTEK

AXIOMTEK GOT321W-521 user manual

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Operation manual

Qomo

Qomo QIT1386 user manual

AMX

AMX AXP-PPC Dimensional drawing

Sartorius

Sartorius X3 PR 5410 operating manual

AMX

AMX Modero X Series quick start guide

Advantech

Advantech TPC-30 Series user manual

B&R Industries

B&R Industries MAPPC900-ENG user manual