DFI KS150 User manual
1
KS150/190/215-SD Installation Guide
Package Contents
•
One 15", 19", or 21.5" Modular Touch Panel PC
•
3-pin Terminal Blcok Connector
•
SATA and Mini PCIe Installation Screws
DFI reserves the right to change the specications at any time prior to the
product's release. For the latest revision and more details of the installation
procedure, please refer to the user's manual on the website.
www.d.com
2
Panel
Front OSD Functions (only for models with front OSD)
Notes on OSD Settings:
The front OSD is capable of controlling the system in the following ways in addition to
its explicit functions.
1. System Power On/Off: Press the Backlight on/off button for 3 seconds.
2. Light Sensor On/Off: Press the Brightness up arrow for 3 seconds.
3. OSD Lock/Unlock: Press the Brightness down arrow for 3 seconds.
4. The Alarm LED has no funtion for the KS-SD Series.
Backlight or Power
on/off Volume Brightness
Power HDD Alarm LED
Bottom View
Top View
DC-in
DVI-D
(DVI-I connector)
LAN 1 LAN 2
VGA
USB 3.0
COM 2
Power Button
Reset Button
COM 3 COM 4
Status LED (Orange)
HDD LED (Red)
COM 1
Remote Power Switch
3
Removing the Chassis Cover
1. Make sure the system and all other peripheral devices connected to it
have been powered-off.
2. Disconnect all power cords and cables.
3. The 6 mounting screws on the rear side of the system are used to
secure the cover to the chassis. Remove these screws and put them in a
safe place for later use.
4. Lift the cover to open the system.
5. The Mini PCIe, M.2 and the SODIMM slots are readily accessible after
removing the chassis cover.
Mini PCIe
Sockets
SATA drive bay
Mounting Screw
4
The system can accommodate one SATA drive. Please use the following
procedure to install a SATA drive in the system.
1. Before installing the SATA drive, connect the SATA data/power cable
to the SATA data connector of the SATA drive. Then install the SATA
drive onto the HDD bracket with the provided mounting screws.
Installing a SATA Drive
Mounting Screws
Mounting screws
SATA data and power cable
2. Place the SATA drive installed with the HDD bracket in the system.
Align the mounting holes on the HDD bracket with the mounting holes
on the drive bay and use the provided mounting screws to secure the
drive in place.
Mounting Screws
5
3. Connect the other end of the SATA data/power cable to the SATA data
and power connectors on the system board respectively.
SATA power connector
SATA data connector
6
Installing a SODIMM
The system supports two DDR4 SODIMM socket. To install a memory mod-
ule, grasp the memory module by its edges and align the module’s notch
with the socket’s notch; then insert the memory into the socket at an
angle and push it down until you feel a click.
Notes:
1. The system supports dual-channel conguration. To enable dual-channel,
populate both SODIMM sockets.
2. If installing only one memory module, please install it on the memory socket
labeled DIMM 1 (the one closer to the edge of the board).
3. The SODIMM sockets can only accept DDR4 memory modules. Please do not
install other types of memory modules.
Insert the memory
at an angle
SODIMM module
installed into the socket
7
The system board is equipped with 2 Mini PCIe slots: one full-size and
(PCIe/USB signals) and one half-size slot (USB/mSATA signals). Here we will
demonstrate the installation of a full-size Mini PCIe card.
1. Grasp the Mini PCIe card by its edges and align the notch in the
connector of the Mini PCIe card with the notch in the connector on the
system board.
2. Push the Mini PCIe card down and use the provided mounting screw to
secure the card on the system board.
Installing a Mini PCIe or mSATA Card
Mounting screw
Antenna hole
8
0.82mm
Important:
The bottom side of a full-size Mini PCIe module should have a component height
restriction of 0.82 mm and will sit ush against the connected half-size Mini PCIe
module if such a component is used and the half-size slot is connected with a
module.
9
Assemble the Modular Panel PC
The modular panel PC comprises two parts: a box module and a panel module.
1. Take off the cover of the ADP connector. Hold the box module with its
ADP connector (female) in line with the ADP connector (male) of the
panel module. Align the box module with the panel module using the
alignment posts.
Note:
If the orientation of the assembly is not correct, the box module will not seat evenly on top
of the panel module, which results in some space in between them and indicates that the
ADP connectors are not engaged. When this is the case, please turn the box module the
other way around.
2. Hold the box module with its ADP connector (female) in line with the
ADP connector (male) of the panel module. Align the box module with
the panel module using the alignment posts.
ADP
connector
cover screw
ADP
Connector
(female)
Box Module
Alignment
Post
Panel Module
10
3. Seat the box module on top of the panel module with the alignment
post effortlessly sliping into the designated holes on the box module.
Press to install these two modules and secure the installation with 8
mouting screws.
Mounting Screw
Mounting Screw
Alignment
Post
Box + Panel Module
This manual suits for next models
3
Table of contents
Other DFI Touch Panel manuals
DFI
DFI TPC150-SD Operating and maintenance instructions
DFI
DFI KS150-BT User manual
DFI
DFI KS156P-EHL User manual
DFI
DFI KS200 User manual
DFI
DFI VS436 (15") User manual
DFI
DFI KS210-IMX6 User manual
DFI
DFI KS-SD Series User manual
DFI
DFI PPC Workstation 19 480 User manual
DFI
DFI TPC121 Installation guide
DFI
DFI KS310-IMX6 User manual
Popular Touch Panel manuals by other brands
IBASE Technology
IBASE Technology ASTUT-152-RE1S user manual
YASKAWA
YASKAWA TP 610C manual
B&R
B&R Power Panel C Series user manual
Beijer Electronics
Beijer Electronics X2 control Hardware and installation manual
AXIOMTEK
AXIOMTEK GOT321W-521 user manual
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Operation manual
