Denon AVR-X4000 Guide

Denon X4000 Factory Reset

1.0 Save Settings

1.1. Using IE to perform a SAVE of the config.dat file may or may not work, however using another browser

will generally work every time. Turn ON the receiver but select a non-network input. Enter the following URL

into your laptop/desktop web browser replacing the 192.168.1.xxx with your own unit's IP address. The URL is

case-sensitive.

1.2. <192.168.1.xxx/SETUP/OTHERS/SAVE/f_config_save.asp>

1.3. This dialog should be displayed on the laptop:

1.4. If you are having difficulty SAVE(ing) a file, make sure to stop any network playback by first playing

something on the network and then either pressing the Stop Playback (black square) or the ENTER button on

the remote for a few seconds. You may also need to set "Network Standby" to OFF (contrary to what the

Owner's manual indicates). Perform a “soft reset”(unplug power for 5 minutes) after SAVE.

1.5. The config.dat file should be about 348kB for old models, 952kB for newer ones; however, it's a good idea

to confirm the AVR is actually saving data in the file as the file size will be 348kB or 952kB whether it's all

zeroes or filled with zeroes and some data. If it is all zeroes, it will not LOAD successfully. Use a Windows or

Mac hex viewer to view the file and confirm whether it is all zeroes or not. (Tip: some word processors will also

display the HEX codes if you rename a copy of the file to “config.txt.”) If you do get a file with all zeroes or if a

file with data won't load properly, then perform a soft reset, set Network Standby to OFF/Off in Standby, cycle

the AVR OFF/ON and then try a SAVE again which should result in a config.dat file with non-zero data.

1.6. It's also a good idea to SAVE the settings prior to a firmware update even though firmware updates

generally don't change the system settings. If you are having difficulty using IE, try using Firefox or Chrome

(see Post #2775 of the 2013 Denon AVR thread). If still no joy when trying to LOAD the config.dat file, try

setting IP Control to "Off in Standby", cycle the AVR to OFF, then ON again and try the LOAD. If yet still no

joy, try resetting the microprocessor and then do the LOAD again.

2.0. Microprocessor Reset

2.1. Turn off the power using ON/STANDBY.

2.2. Press ON/STANDBY while simultaneously pressing "INFO" and "BACK" (under front panel flap).

2.3. Once the display starts flashing at intervals of about 1 second, release the two buttons (hold for at least 4-5

seconds). If in step 2.3 the display does not flash at intervals of about 1 second, start over from step 2.0.

2.4. jdsmoothie from the AVS Denon forum suggests doing this rest 4 or 5 times in a row, not just once.

3.0. Optional: Network & Microprocessor Reset

3.1. Turn off the power using ON/STANDBY.

3.2. Press ON/STANDBY while simultaneously pressing the "UP" and "DOWN" arrows (under front panel

flap).

3.3. Once the display starts flashing at intervals of about 1 second, release the two buttons (hold for at least 4-5

seconds). If in step 3.3 the display does not flash at intervals of about 1 second, start over from step 3.0.

3.4. jdsmoothie from the AVS Denon forum suggests doing this rest 4 or 5 times in a row, not just once.

4.0. Load Settings

4.1. Using IE to perform a LOAD of the config.dat file may or may not work, however using another browser

will generally work every time. Enter the following URLs into your laptop/desktop web browser replacing the

192.168.1.xxx with your own unit's IP address. The URL is case-sensitive.

4.2. <192.168.1.xxx/SETUP/OTHERS/LOAD/f_config_load.asp>

4.3. The following dialog should be displayed on the laptop:

4.4. Click on “Choose File” and navigate to the location where you saved the config file. Select it, and then click

“Upload.”

4.5. The laptop should display an "Uploading" message in the lower left corner of its display. Once the file is

uploaded to the AVR (~ 30 seconds), the AVR will power to Standby and display "Loading" on the front panel

display. The LOAD process will take about 6 minutes.

4.6. If the LOAD has completed successfully, a “Load Completed” image should be displayed on your laptop

and the AVR will power back ON again (Yeh!).

4.7. Perform a “soft reset”(unplug power for 5 minutes) after LOAD.

djl 18 March 2017

Table of contents

Other Denon Stereo Receiver manuals

Popular Stereo Receiver manuals by other brands

Marantz

Marantz CINEMA 70S owner's manual

Kenwood

Kenwood KMDX92 instruction manual

Yamaha

Yamaha RX-830 owner's manual

Pioneer

Pioneer AVH-Z7250BT owner's manual

Yamaha

Yamaha RX-750 owner's manual

Pioneer

Pioneer SC-LX904 Initial setup guide

Sony

Sony XAV-1500 operating instructions

Radio Shack

Radio Shack DX-399 owner's manual

Sony

Sony STR-DE535 - Fm Stereo/fm-am Receiver operating instructions

Pioneer

Pioneer SX-1000TA operating instructions

Yamaha

Yamaha MusicCast TSR-5B3D owner's manual

Sony

Sony STR-DE335 - Fm Stereo/fm-am Receiver operating instructions

Sony

Sony STR-DG500 - Multi Channel Av Receiver Service manual

Panasonic

Panasonic AJSD955B - DVCPRO50 STUDIO DECK Brochure & specs

Pioneer

Pioneer SX-838 Service manual

Sherwood

Sherwood S-2660CP operation instruction

Sony

Sony STR-K790 - Lifier Service manual

Pioneer

Pioneer XR-VS77 Service manual