Dematech Dema-Craft 60l User manual
www.dematechsa.com | info@dematechsa.com | +27 (0) 21 385 0483
13 Michigan Street, Airport Industria, 7490, Cape Town, South Africa
Dema-Craft 60l
Operation Manual
Thank you for purchasing the Dema-Craft.
Please follow the instructions to get the best use from your brewing vessel.
The process described is just a guide.
We suggest that you use this process for your rst few batches before
adjusting to suite your brewing style.
EnglishEnglish
www.dematechsa.com
Head Oce:
Cape Town, South Africa
info@dematechsa.com
Oce Number: +27 (0) 21 385 0483
13 Michigan Street, Airport Industria, 7490, South Africa
1.
SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS
• Read all the instructions carefully, and keep this manual for future reference.
• Check the products rating label and make sure the brewing vessel voltage is t
for your outlet voltage before using.
• Do not use the device if the cord or plug is damaged.
• Switch o the brewing vessel before removing the plug.
• Only move the brewing vessel when the power is o and it is empty (no water).
• This appliance requires a 13amp-16amp plug.
• Never submerge the brewing vessel. To clean the exterior, use a damp cloth.
Always protect the electric power cable from water.
• Do not switch on the machine if the vessel is empty. The machine does have a
dry-boil cut-o switch to turn the element o if it overheats (when there is no
water) but the element and electronics may still be damaged. The warranty
does not cover damage due to dry-boil.
• Please do not turn on the pump for more than 5 minutes at a time during wort
boiling (Because bubbles will cause the pump to idle and wear out under high
temperature). It is not recommended to use the pump for pumping out the wort
after cooling (rather use the tap on the front of the unit). Hops and trub may
enter the pump, potentially blocking and damaging the system
WHAT’S IN THE BOX?WHAT’S IN THE BOX?
1 Digital controller1 Digital controller
2 Switches (PCB and Pump)2 Switches (PCB and Pump)
3 Faucet3 Faucet
4 Built-in pump4 Built-in pump
5 Circulation valve5 Circulation valve
6 Cam-lock connector6 Cam-lock connector
7 Circulation tube7 Circulation tube
2.
PARTSPARTS
Telescopic overow
tube + adjustable for
half batches
Top sparge plate
for grain basket
Glass lid cover with
hole for circulation
pipe
Circulation pipe
(Cam-lock
connector)
Filter tube Screw nutWhite screw cap
cover
Bottom tube
Bottom sparge plate
for grain basket
Grain basket Grain basket handle
ADDITIONAL ACCESSORIES:ADDITIONAL ACCESSORIES:
13m chiller
coil
Whirlpool
arm
Hop sieve Grain paddle Thermowell
3.
OPERATIONOPERATION
Switch operation
The switch “PCB” is the ON/OFF switch for the power to the Digital Controller that
controls the heating elements. The switch “PUMP” is the ON/OFF-switch for the
pump.
Switch ON Switch OFF
Tap operation
Closed To open, pull the
safety latch up and turn
the lever 90°
counterclockwise.
To close, pull the safety
latch up and turn the le-
ver clockwise by 90°.
Valve operation
This valve is to open and close the wort circulation from the pump. It is also used to
adjust the wort ow during mashing.
Closed Open
If the Switch is on you will see a red
light
4.
Componenets prepared Install the top
sparge plate,
white screw cap
cover at the top.
Circulation tube assembly
1 2 3 4
Insert circulation
pipe into the
cam-lock
connector.
To lock, push the
Cam-lock levers
down.
Now it’s locked
and ready to
use.
Direct the hose
through the
glass lid
• Adjust the ow rate using the blue valve. If the ow is too fast, the grain
basket will overow down the central pipe, and the bottom of the boiler
may run dry.
• Adjust the ow until the ow from the pump matches the speed at which
the wort ows through the grain. This may need to be adjusted during the
Note:
Grain basket overflow pipe assembly
Use the screw to
connect the bot-
tom sparge plate
with telescopic
overow tube
Use screw driver to attach the two metal handles to the top sparge plate. These han-
dles are already attached.
Secure the overow pipe into the bottom sparge plate by inserting the larger, thread-
ed end of the overow pipe through the hole in the bottom plate and securing the nut
from the bottom. Make sure that the nut is only nger tight. Attach the smaller nut on
the top of the overow pipe.
The white grain stopper cap is only used while mashing in so that the milled grain
cannot fall into the overow pipe. Remove this cap when all grains have been added.
5.
Grain basket assembly
Use the handle to lower
the grain basket into the
Dema-craft. Make sure
that the supports on the
basket are hooked onto
the support ring
When adding the mash
water and grains,
remove the top sparge
plate and add the grain
stopper.
When the mashing is
completed, use the handle
to lift the Grain basket up
and hook its bottom
supports onto the support
ring
Bazooka mesh filter assembly on tap
Bottom little tube assembly
Note: Please insert this tube into the pump before using the brewing vessel to prevent
the malt from clogging the pump inlet.
4.
6.
HOW TO USE THE CONTROLLER?HOW TO USE THE CONTROLLER?
Control Panel and Key Functions
Temp button Press to set target temperature for each step
Power button Press to set power for each step
Timer button Press to set timer for each step
- button Press to reduce the value
+ button Press to increase the value
Start/Stop Press to start or stop the program
Manual/Pause Press to enter manual mode.
Press to pause the program on manual mode.
Auto/Pause Press to enter auto mode.
Press to pause the program on Auto mode.
S/P: W Set the power
S/T: ℃ Set the temperature
-H When it’s ashing, it means it is heating to
target temperature
7.
Manual Mode Setting
1. Switch on the PCB switch, then press the MANUAL/PAUSE button to enter manual
mode.
2. Press the TEMP button. The temperature set-point (S/T: XX.X°C) at the bottom right
of the screen will ash and you can use the – and + buttons to set your temperature.
3. Press the POWER button. The power set-point (S/P: XXXXW) at the bottom left of
the screen will ash and you can use the – and + buttons to set your wattage. We rec-
ommend 3000W for raising temperature up between steps. 1500W during your mash-
ing phase to maintain mash temperature. And once boiling, drop to 2500W to maintain
a rolling boil.
8.
4. Press the TIMER button. The time (XX min) at the top right of the screen will ashing
and you can use the – and + buttons to set your countdown timer.
5. Once the TEMP, POWER and TIMER have been set, press the START/STOP button to
start the machine. The H – symbol at the top left of the screen will ash to show that
the machine is heating. The machine will then heat the liquid up to your temperature
set-point. Once it reaches the set-point, the machine will chime and start the count-
down timer while maintaining the set-point temperature. The time will ash while the
timer is counting down.
Note: The H – symbol will continue ashing even when the elements are o. Once the
timer reaches zero, the machine will chime and the word END will ash on the screen.
Press the START/STOP button to stop the chime.
6. To edit any of the TEMP, POWER or TIMER settings, press the MANUAL/PAUSE
button again. To return to your program after adjusting any of the settings, press the
MANUAL/PAUSE button again
7. The default boiling temperature is 100℃. The timer will not be triggered if temperature does
not indicate 100℃.
8. If the machine starts to boil, but shows a lower temp on the display (i.e. if you are brewing
at a higher altitude than sea level), make the following adjustment to set the temp at 100℃ and
trigger the timer.
9. Press START/STOP until only the temperature is displayed on the screen. Press “-” and “+”
button together for 5 seconds and then release, the display will show the C1 (temperature
oset for celsius) or F1 (temperature oset for fahrenheit). Press the MANUAL/PAUSE button
until the display shows C2 (boil temperature oset for celsius) or F1 (boil temperature oset
for fahrenheit).Temperature correction range is from 0℃ to +10℃ or 0℃ to +50℃. If you set C2 to 6℃
then the unit will begin the boiling stage of the program at 94℃.
8. Press MANUAL/PAUSE button during heating to go back to the edit page. You can edit
Temp/Power/Timer, then press the MANUAL/PAUSE button again to resume.
NOTE: Long press TEMP for 5 seconds, switch degree centigrade to Fahrenheit.
This operation only can be preceded when you switch on the machine before any setting. 9.
Table of contents
Popular Dispenser manuals by other brands
Silver King
Silver King Majestic SK12MAJ Technical manual and replacement parts list
Franke
Franke F3Dn Twin Service manual
STIEBEL ELTRON
STIEBEL ELTRON UltraHot Plus Operation and installation instructions
DAN DRYER
DAN DRYER 282 installation guide
Essity
Essity Tork 473208 manual
CBS
CBS SD300BU-88 COMPONENT MAINTENANCE MANUAL WITH ILLUSTRATED PARTS LIST
