Delta Agema AG5648 User manual
Delta Networking – Agema Family
AG5648 Leaf/ToR Switch
Installation Guide
ii
AG5648 Leaf/ToR Switch
Copyright
All specications and gures are subject to change without prior notice. Actual products may look
different from the photos.
All trademarks and logos mentioned in this guide are the properties of their respective holders.
Copyright © 2017 Agema Systems Inc. All rights reserved.
Regulatory and Safety Information
This product has been tested in accordance to, and complies with the following safety standards and
electromagnetic compatibility (EMC) inspection standards.
Emissions
Applicable standard
• AS/NZS CISPR 22: Class A
• ICES-003, Issue Class A
• EN 55022: Class A
• VCCI Class A
• FCC CFR 47 Part 15, Subpart B Class A
Safety
Applicable standard
• EN 60950-1, Second Edition
• UL/CSA 60950-1, Second Edition
• IEC 60950-1, Second Edition Including All National
Immunity
Applicable standard
• EN 300 386, EMC for Network Equipment
• EN 55024:
• EN 61000-3-2: Harmonic Current Emissions
• EN 61000-3-3: Voltage Fluctuations and Flicker
• EN 61000-4-2: ESD
• EN 61000-4-3: Radiated Immunity
• EN 61000-4-4: EFT
• EN 61000-4-5: Surge
• EN 61000-4-6: Low Frequency Conducted Immunity
• EN61000-4-8: Power Frequency magnetic eld
• EN61000-4-11: Voltage dips and interruptions
RoHS
Applicable standard All AG-Series components are EU RoHS compliant
Warning: Fiber Optic Port Safety
When using a ber optic port, never look at the transmit laser while it is powered
on. Also, never look directly at the ber TX port and ber cable ends when they are
powered on.
iii
Table of Contents
Table of Contents
Chapter 1: Introduction -------------------------------------------------------------------1
1.1 Overview ------------------------------------------------------------------------------------ 1
1.2 Package Content -------------------------------------------------------------------------- 1
1.3 Features ------------------------------------------------------------------------------------- 2
Chapter 2: Appearance and Mechanism --------------------------------------------3
2.1 Product Overview ------------------------------------------------------------------------- 3
2.2 LED Identication ------------------------------------------------------------------------- 4
2.3 System Requirements ------------------------------------------------------------------- 6
2.4 Data Center Deployment ---------------------------------------------------------------- 7
2.5 Power Supply Modules ------------------------------------------------------------------ 7
2.6 Fan Tray Module -------------------------------------------------------------------------- 8
Chapter 3: Installation ---------------------------------------------------------------------9
3.1 Mounting ------------------------------------------------------------------------------------ 9
3.2 Installing an Optional Transceiver and Cable -------------------------------------11
3.3 Connecting to the Console Port ------------------------------------------------------12
3.4 Connecting to a Power Source -------------------------------------------------------13
Chapter 4: Making the Network Connections ----------------------------------- 15
4.1 Twisted-pair Connections --------------------------------------------------------------15
4.2 Fiber Optic Connections ---------------------------------------------------------------16
4.3 Ethernet Cabling -------------------------------------------------------------------------17
Appendix 1 : Technical Specifications--------------------------------------------- 18
Appendix 2 : Warranty------------------------------------------------------------------- 19
Limited and Support Warranty -------------------------------------------------------------19
Technical Support -----------------------------------------------------------------------------19
1
AG5648 Leaf/ToR Switch
Chapter 1: Introduction
1.1 Overview
The AG5648 is next generation leaf/ToR switch for Data Center Networks, as well as
Enterprise network deployments. It leverage the 100G technology (4x25G Serdes) to provide
48-port 25G SFP28 and 6-port 100G QSFP28 in a compact 1RU form factor with 2.5 times
speed upgrade from current 10Gigabits leaf/ToR switch. The 48 ports 25G are backward
compatible to 10G and the 100G uplink offer dual speed – 40G and 100G.
The AG5648 is also SDN capable and supports ONIE installer and OpenFlow for today’s
open network ecosystem. It also provides comprehensive capability on layer 2 and layer
3 features, including SNMP, Spanning Tree, VLAN, QinQ, Trunk, QoS, RIP, OSPF, IGMP,
DVMRP, PIM-DM, PIM-SM, Access Control, etc. This product which aims for Data Center
Networks also supports advance features such as MPLS, TRILL, PFC, VEPA, QCN, VxLAN
and NVGRE to meet the high-demanding Data Center high performance and virtualization
requirement. The AG5648 is excellent choice for next generation hyper scale and medium
size datacenters and Core/Aggregation switches in Enterprise network environment.
1.2 Package Content
After unpacking this switch, check the contents to be sure you have received all the
components. Then, before beginning the installation, be sure you have all other necessary
installation equipment.
•AG5648 switch
•1 x AC power supply for AC version or 1 x DC power supply for DC version
•Rack-mounting kits
•2 x Velcro strips
•Installation guide
If any item is missing or damaged, contact the vendor immediately, see “Technical Support”.
2
• IntroductionChapter 1
1.3 Features
The following lists the key main features of the AG5648 switch:
•48 x 25GbE SFP28 ports
•6 x 100GbE QSFP28 ports
•1 x OOB Management
•1 x Console port (RJ-45 type)
•1 x USB port
•Hot plugging redundant power supply support
•4 Fan modules
•System / Fan / Power status LED indication
•On board high performance CPU system with large memory
•Internal power supply; Max power 550W (AC version) or 550W (DC version)
•Standard 1U chassis high
•1.8 Tbps full-duplex switching
•Automatic address learning function to build the packet-forwarding information table. The
table contains up to 288K MAC addresses
•Low pin-to-pin latency: Cut-Through & Store and Forward Mode
•16MB of packet buffer memory
•Support Jumbo Frame up to 12Kbyte
3
AG5648 Leaf/ToR Switch
Chapter 2: Appearance and Mechanism
2.1 Product Overview
2.1.1 Front View
Management port x 1
RJ-45 Console port x 1
SFP28 port x 48 QSFP28 port x 6
(Figure 2-1: Front View)
2.1.2 Rear View
PSU x 1
4 Fan tray slots
Secondary PSU
slot x 1 (optional)
USB port x 1
Reset x 1
(Figure 2-2: Rear View)
NOTE:
The switch supports up to two PSUs. However, it is shipped with one power supply
pre-installed in the rear panel of the switch. You may purchase an additional PSU for
redundancy.
4
• Appearance and MechanismChapter 2
2.2 LED Identification
This section provides an overview of the front and rear LEDs.
2.2.1 Front LEDs
System LED
Upper SFP28
Port LED
Power LED
Fan Status LED
Lower SFP28
Port LED
Upper QSFP28 Port LED
Lower QSFP28 Port LED
(Figure 2-3: Front LED Identification)
LED Description
System LED
• Off – No Power
• Blinking Green – Booting, or System in Diagnostic mode
• Solid Green – Normal operation
• Solid Yellow – Critical Alarm
• Blinking Yellow – Non-critical alarm
Power LED
• Solid Green – Booting
• Off – Power is disconnected
When NOS is running:
• Solid Green – 2 Power Supplies are supplied to the switch and operating
normally
• Solid Yellow – Single power supply is installed and operating
• Blinking Yellow – 2 Power Supplies are installed, but only single power supply
is operating
Fan Status
LED
• Solid Green – FAN is operating normally
• Solid Amber – FAN is failed including incompatible airow direction
25G SFP28
slots
• Off – No link
• Solid Green – A valid link 25G link
• Solid Yellow – A valid link 10G link
• Blinking Green – Packet transmission or reception in progress
5
AG5648 Leaf/ToR Switch
LED Description
100G QSFP28
slots
LED1
• Off – No link
• Solid Green – A valid 100G link
• Solid Amber – A valid 40G link
• Solid Blue – A valid 10Gbps link
• Solid Purple – A 10Gbps link
LED 2 and 4 (working in breakout)
• Off – 40/100G operation (assuming LED1 is illuminated) or No link
• Solid Blue – A valid 25Gbps link
• Solid Purple – A valid 10Gbps link
Management
port
Link LED
• Off – No link is established on the port
• Solid Yellow – A valid link at 10/100Mbps is established on the port
• Solid Green – A valid link at 1000Mbps is established on the port
Act LED
• Off – No link is established on the port
• Blinking Green – Activity, transmitting or receiving packet at this port
2.2.2 Rear LEDs
Power Supply LED
Fan Tray LED
(Figure 2-4: Rear LED Identification)
LED Description
Fan Tray LED
• Solid Green – Fan operating normally
• Solid Red – Fan failed
Power Supply
LED
• Off – No power or power supply failed
• Solid Green – Power is ok
6
• Appearance and MechanismChapter 2
2.3 System Requirements
Component Requirement
System requirements
Switch fabric capacity Non-blocking full wire speed on all packet sizes
Forwarding architecture Store and forward or cut-through
Port packet forwarding rate
(at 64 Bytes) 14880000 pps (10Gb)
MAC address entries
supported Up to 136K entries
Memory type 16MB buffer memory
OOB port 10/100/1000Mbps, auto sensing, auto negotiation
Host Support • IPv4: 8K min./72K max.
• IPv6: 4K min/36K max.
LPM Route Support • w/o URPF: IPv4 128K, IPv6/64 85K, IPv6/128 21K
• w/ URPF: : IPv4 64K, IPv6/64 21K, IPv6/128 5K
Priority Queues 20 priority queues per port
MAC Address Aging
Support 1,000,000 seconds programable (Default 300 seconds)
Spanning Tree Support
• Support IEEE802.1d STP
• Support IEEE802.1s MSTP
• Support IEEE802.1w RSTP
Host Support 136K shared entries with MAC Table
LPM Routes Support 128K shared entries with MAC Table
Serial Console • Provide visual feedback of the boot process to the user
• Timeout after period of inactivity
Port Trunking • IEEE802.3ad Link Aggregation Protocol (LACP)
• Up to 1024 groups with 256 member per group
Port requirements
Speed Capability per Port
• 10G/25Gbps (SFP28 port)
• 40G/100Gbps (QSFP28 port)
• 10G/25G/40G (QSFP28 port, working in breakout)
Full-Duplex Flow Control Support the IEEE 802.3x PAUSE frame
7
AG5648 Leaf/ToR Switch
2.4 Data Center Deployment
The following gure illustrates the converaged Ethernet data center deployment.
Spine
Leaf
6x100G uplink
25G downlink via
Breakout cable
AG5648
25G downlink
AG5648
25G downlink
AG5648
25G downlink
AG9032 v1 AG9032 v1 AG9032 v1 AG9032 v1
AG9032 v1
(Figure 2-5: Converaged Ethernet Data Center Deployment)
2.5 Power Supply Modules
The power supply modules are hot-swappable power supply units (PSUs) for the switch.
You can install up to two PSUs. The PSUs operate in a load-sharing mode and provides 1+1
redundancy.
(Figure 2-6: Power Supply Unit)
NOTE:
1+1 redundancy is a system where a switch power supply is backed up by
another switch power supply in a load-sharing mode. If one power supply fails,
the other power supply takes over the full load of the switch.
WARNING:
• The switch includes plug-in power supply and fan tray modules that are
installed into its chassis. All modules have a front-to-back airow direction.
• Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
• Remove the power cable from the module prior to removing the module
itself. Power cable must not be connected prior to insertion in the chassis or
equivalent.
Table of contents
Other Delta Switch manuals
Delta
Delta MST-01 User manual
Delta
Delta DVS Series User manual
Delta
Delta PFS3106 User manual
Delta
Delta DS-7604NI-K1/4P User manual
Delta
Delta DVS-G008W01 User manual
Delta
Delta EXPERT-POE-1616 User manual
Delta
Delta Agema Series User manual
Delta
Delta AG9064 User manual
Delta
Delta HYPERSPROUT User manual
Delta
Delta DVS Series User manual
Delta
Delta LE-764501 User manual
Delta
Delta EXPERT-POE-54G User manual
Delta
Delta AG6248C User manual
Delta
Delta DVS Series User manual
Delta
Delta AGC7648A User manual
Delta
Delta AG7648 User manual
Delta
Delta STS30002SR00035 User manual
Delta
Delta TL-SG1024D User manual
Delta
Delta AG9032 V1 User manual
Delta
Delta DVS-103I02C-DLR User manual
