Dell PowerConnect 3324 User manual

Dell™PowerConnect™3324/3348User'sGuide

Overview

Hardware Description

Installing the PowerConnect 3324/3348 Switch

Configuring the PowerConnect 3324/3348 Switch

Getting Started

Configuring System Information

Configuring Switch Information

Viewing Statistics

Configuring Quality of Service

Getting Help

Information in this document is subject to change without notice.

©2003DellInc.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerConnect, Dell OpenManage, PowerEdge, Inspiron, Dell Precision, Dimension, OptiPlex, Axim, PowerVault, PowerApp, DellNet, and

Latitude are trademarks of Dell Inc.; Microsoft and Windows are registered trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

November 2003

NOTE: Notes indicate important information that helps you make better use of your device.

NOTICE: Notices indicate either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: Caution indicates a potential for property damage, personal injury, or death.

Back to Contents Page



Configuring the PowerConnect 3324/3348 Switch

Dell™PowerConnect™3324/3348User'sGuide



Configuration Overview



This section describes the initial device configuration and includes:

lInitial Device Bootup

lPreliminary Configuration Requirements

lConfiguring Stacking



After all the device external connections are in place, a terminal must be connected to the device to monitor the boot and other procedures. The order of

installation and configuration procedures are illustrated in the following flowchart:



Instructions for setting up the device and hardware are provided in the preceding sections. For a first-time installation, the standard device installation is

performed. There are other special functions which can be performed, but this suspends the installation process and results in a system reboot. This option is

described later in this section.



Configuration Overview

Sample Configuration Process

General Configuration Information

Configuring Stacking

Terminal Connection Configuration

Rebooting the Device

Other Configuration Requirements

Startup Menu Functions

Booting the Device

Downloading the Software to Stacking Units

Device Configuration Introduction

Defining SNMP Settings

Initial Configuration

Connecting Devices

Advanced Configuration

General Configuration Information



Dell™PowerConnect™3324/3348isprovidedwithpre-defined implemented features and setup configuration.



Auto-Negotiation



Auto-negotiation allows a device to advertise modes of operation and share information with another device that shares a point-to-point link segment. This

automatically configures both devices to take maximum advantage of their abilities.



Auto-negotiation is performed completely within the physical layers during link initiation, without any additional overhead to either the MAC or higher protocol

layers. Auto-negotiation allows the ports to do the following:

lAdvertise their abilities.

lAcknowledge receipt and understanding of the common modes of operation that both devices share.

lReject the use of operational modes that are not shared by both devices.

lConfigure each port for the highest-level operational mode that both ports can support.



If connecting a port of the switch to the network interface controller (NIC) of a workstation or server that does not support auto-negotiation or is not set to

auto-negotiation, both the switching port and the NIC must be manually set with the Web browser interface or CLI commands to the same speed and duplex

mode.



Switching Port Default Settings



The following table describes the Port default settings.

Port Default Settings 

The following is an example for changing the port speed on port 1/e5 using CLI commands:



console> enable



console# configure



Console (config)# interface ethernet 1/e5



Console (config-if)# speed 100



The following is an example for enabling flow control on port 1/e5 using CLI commands:



NOTICE: If the station on the other side of the link attempts to auto-negotiate with a port that is manually configured to full duplex, the auto-

negotiation results in the station attempting to operate in half duplex. The resulting mismatch may lead to significant frame loss. This is inherent in the

auto-negotiation standard.

Function

Default Setting

Port speed and mode

10/100M copper ports: auto-negotiation

1000M auto-negotiation

Port forwarding state

Enabled

Port tagging

No tagging

Head of line blocking prevention

On (Enabled)

Flow Control

Off

Back Pressure

Off

console> enable



console# configure



Console (config)# interface ethernet 1/e5



Console (config-if)# flowcontrol on



The following is an example for enabling back pressure on port 1/e5 using CLI commands:



console> enable



console# configure



Console (config)# interface ethernet 1/e5



Console (config-if)# back-pressure



Baud Rate



The baud rates can be manually changed to any of the following values:

l2400

l4800

l9600

l19,200

l38,400

l57,600

l115,200



The following is an example configuration for changing the default baud rate using CLI commands:



console> enable



console# configure



console(config)# line console



console(config-line)# speed 9600



NOTE: The default baud rate is 9600.

NOTE: Closing the device does not return the default baud rate. It must be specifically configured.

NOTE: In order to enter configuration mode, you must specify administrative level 15 privileges.

console(config-if)# exit



console(config)# exit



Terminal Connection Configuration



The PowerConnect 3324/3348 requires the following Terminal Connection parameters for configuration:

lno parity

lone stop bit

l8 data bits



Other Configuration Requirements



The following is required for downloading embedded software and configuring the device:

lASCII terminal (or emulation) connected to the Serial port in the back of the unit.

lAssigned IP address for PowerConnect 3324/3348 for device remote control using with Telnet, SSH, etc.



Booting the Device



When power is turned on with the local terminal already connected, a device goes through POST (Power On Self Test). This built-in power-on test runs every

time the device is initialized. The POST checks hardware components to determine if the device is fully operational before completing boot up.



If a critical problem is detected, the program flow stops. If POST passes successfully, the code is decompressed into the RAM memory.



The POST messages are displayed on the terminal and indicate test success or failure.



To boot the device:

1. Ensure the ASCII cable is connected to the terminal.

2. Connect the power supply to the device; the device begins booting up. The boot-up test first counts the device memory availability and then continues

to boot-up. The following screen is an example of the displayed POST test:



------ Performing the Power-On Self Test (POST) ------



UART Channel Loopback Test......PASS



Testing the System Cache.......PASS



Testing the System SDRAM.......PASS



NOTE: The configuration process defines only one port.

Boot1 Checksum Test........PASS



Boot2 Checksum Test........PASS



Flash Image Validation Test......PASS



Testing CPU PCI Bus Device Configuration...PASS



BOOT Software Version 1.30.11 Built 27-JAN-2003 10:06:03



Processor: MPC8245 Rev 0.12, 250 MHz (Bus: 100MHz), 32 MByte SDRAM.



I-Cache 16 KB, linesize 32.D-Cache 16 KB, linesize 32.



Cache Enabled.



Autoboot in 2 seconds -press RETURN or Esc. to abort and enter prom.



The auto-boot message that appears at the end of the POST (see the last lines) indicates that no problems were encountered during boot.



At this point, a user input can be entered to get the Startup menu if it is necessary to run special procedures that can be invoked from this menu. To enter the

Startup menu, the <Esc> or <Enter> keys must be pressed within the first two seconds after the auto-boot message appears. For details regarding the

Startup menu, see Startup Menu Functions.



If no user input is entered, the system continues operation by decompressing the code into RAM. The code starts running from RAM and the list of available

port numbers and their states (up or down) are displayed.



Preparing to decompress.



Decompressing SW from RSCOD_2



85e000



Running from RAM.



******************************************************Running SW Ver. 3.30 Date 03-Feb-2003 Time 10:10:37

******************************************************



HW version is X.X



NOTE: The following screen is an example configuration. Items such as addresses, versions, and dates may differ for each device.

Base Mac address is: 00:01:02:03:04:05



Dram size is: 32M bytes



Dram first block size is: 20M bytes



Dram first PTR is: 0xB70000



Flash size is: 8M



STAND ALONE



The BCM5625_A1 0 initiate successfully



The BCM5625_A1 1 initiate successfully



02-Jan-2000 01:01:11%SSHD-W-NOHOSTKEY: SSHG_init: The SSH daemon cannot listen



for incoming connections, because a host key has not been generated.



The service will start automatically when a host key is generated.



01-Jan-2000 01:01:11 %INIT-I-InitCompleted: Initialization task is completed



console> 01-Jan-2000 01:01:12 %PS-I-PSUP: Power Supply #1 is up



01-Jan-2000 01:01:12%PS-W-PSDOWN: Power Supply #2 is down



01-Jan-2000 01:01:12%LINK-W-Up: 1/e1



01-Jan-2000 01:01:12%LINK-W-UP: 1/e2



01-Jan-2000 01:01:12%LINK-W-Up: 1/e3



01-Jan-2000 01:01:12%LINK-W-UP: 1/e4



01-Jan-2000 01:01:12%LINK-W-Up: 1/e5



01-Jan-2000 01:01:13%LINK-W-Up: 1/e9



After the device has been booted successfully, the system prompt appears (console>) and the configuration process can be started. The local terminal can be

used for configuration.



Device Configuration Introduction



There are two types or levels of configuration. The initial configuration describes basic configuration functions with basic security considerations. The advanced

configuration includes dynamic IP configuration and more advanced security considerations.



console> enable



console# copy running-config startup-config



Initial Configuration



Initial configuration starts after the device has booted successfully. The initial configuration scope for the device includes:

lStatic IP address and Subnet Mask

lDefault gateway

lUser name and privilege level must be configured to allow remote management.



If the device is to be managed from an SNMP-based management station, SNMP community strings must also be configured.



Static IP Address and Subnet Mask



In PowerConnect 3324/3348 devices, IP interfaces can be configured on each port and no limitation on the number of IP interfaces is imposed. After entering

the configuration command, it is recommended to check if a port was configured with the IP address by entering the "show ip interface" command.



To configure an interface on a VLAN, enter the commands at the system prompt as shown in the following configuration example:



console> enable



console# configure



console(config)# interface vlan 1



console(config-if)# ip address 100.1.1.1 /8



console(config-if)# exit



console(config)# exit

NOTICE: After making any configuration changes, the new configuration must be saved before rebooting. To save the configuration, enter:

NOTICE: Only one VLAN can be assigned an IP address. If you assign an address to any other VLAN, the new address overrides the original IP

address.



console# show ip interface



Gateway IP Address Activity status



----------------------- -----------------------



IP Address I/F



----------------------- ----------------------



100.1.1.1/8 vlan 1



console#



To configure an interface on a port, enter the commands at the system prompt as shown in the following configuration example:



console> enable



console# configure



console(config)# interface ethernet 1/e1



console(config-if)# ip address 10.1.1.1 255.0.0.0



console(config-if)# exit



console(config)# exit



console# show ip interface



Gateway IP Address Activity status



----------------------- -----------------------



IP Address I/F



----------------------- ----------------------



10.1.1.1/8 1/e1



console#



Default Gateway



To manage a PowerConnect 3324/3348 device from a remote network, a default gateway, which is the gateway that a device uses if a specific gateway is not

specified, must be configured. The configured gateway IP address must belong to the same subnet as one of the device IP interfaces.



To configure a default gateway, enter the command at the system prompt as shown in this configuration example:



console> enable



console# configure



console(config)# ip default-gateway 100.1.1.100



console(config)# exit



User Name, Password, and Privilege Level



IMPORTANT: To manage a device from a remote terminal or Web Management Interface, a user name, a password, and the highest privilege level (15)

must be entered. (The highest level provides access to the CLI configure context.) For details about the privilege level, see the CLI Reference Guide.



The configured user name is entered as a login name for remote management sessions. To configure user name and privilege level, enter the command at the

system prompt as shown in the configuration example:



console> enable



console# configure



console(config)# username admin password admin level 15



console(config)# exit



SNMP Community Strings



Other manuals for PowerConnect 3324

This manual suits for next models

Table of contents

Other Dell Switch manuals

Dell

Dell PowerConnect 2024 User manual

Dell

Dell POWERCONNECT 2800 Series User manual

Dell

Dell PowerConnect W-IAP175P User manual

Dell

Dell N2000 Series User manual

Dell

Dell PowerVault 630F Operator's manual

Dell

Dell PowerConnect W-Series FIPS Owner's manual

Dell

Dell Networking S55 User manual

Dell

Dell PowerConnect 5316M User manual

Dell

Dell S4048-ON User manual

Dell

Dell PowerConnect B-8000 Use and care manual

Dell

Dell PowerConnect 5424 User manual

Dell

Dell PowerConnect 3548 User manual

Dell

Dell PowerConnect 8024 User manual

Dell

Dell PowerConnect 8024 User manual

Dell

Dell EMC PowerSwitch N3000E-ON Series Quick start guide

Dell

Dell Console Switch User manual

Dell

Dell PowerConnect 2124 User manual

Dell

Dell PowerConnect 3024 User guide

Dell

Dell PowerConnect 8024 User manual

Dell

Dell PowerEdge R730xd Quick reference guide

Dell

Dell PowerConnect 6224 Operating instructions

Dell

Dell 5324 - PowerConnect Switch Installation and operating instructions

Dell

Dell Remote Console Switch User manual

Dell

Dell POWEREDGE M905 Technical manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual