Dell SCv2080 User manual
Dell Storage Center
SCv2080 Storage System
Getting Started Guide
Regulatory Model: E11J
Regulatory Type: E11J001
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make
better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or
loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
Copyright ©2016 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other
trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be
trademarks of their respective owners.
2016 - 12
Rev. A00
Setting Up the Storage System
Consider the following best practices when setting up an SCv2080 storage system.
• Dell recommends that you use a dedicated SAN network for data transmission
when using a Fibre Channel or iSCSI storage system.
• Complete the Worksheet to Record System Information in this guide before
configuring the storage system.
• Always configure redundant data paths to provide alternate paths to and from
the host server should one of the data paths become disabled.
• Before connecting any cables between the storage system and host server or
expansion enclosure, physically label each port and connector.
• Always follow proper power-up and power-down procedures when cycling power
across the network. Verify that critical network components are on separate
power circuits.
NOTE: This product is intended for restricted access locations, such as a
dedicated equipment room or equipment closet.
WARNING: If installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater than room
ambient temperature. Therefore, consideration should be given to installing
the equipment in an environment compatible with the maximum ambient
temperature (Tma) specified by the manufacturer.
Safety Warnings
Heavy weight warning
A fully configured SCv2080 storage system weighs up
to 130 kg (287 lb). An unpopulated storage system
weighs 62 kg (137 lb). Use appropriate lifting methods
when installing the storage system.
High temperature warning
The operating temperature inside the drawers of a
storage system can reach up to 60°C (140°F). Take
3
care when opening drawers and removing drive
carriers.
Electrical disconnection
Indicates that all electrical supply connections to the
storage system must be disconnected before
proceeding.
Battery pack warning
Remove the battery pack before removing a storage
controller from the storage system.
WARNING: Installing an incompatible battery may increase the risk of fire or
explosion. Observe the following precautions:
• The battery should only be replaced with a battery that is the same or
equivalent as the factory installed battery.
• Do not attempt to open or service the battery. Do not dispose of the
battery in a fire or with household waste. Contact the local waste disposal
agency for the location of the nearest battery deposit site.
Laser Radiation for Fibre Channel Storage Systems
CAUTION: Class I laser radiation when open, avoid exposure
to beam.
WARNING: Laser radiation, avoid direct exposure to beam.
The unit is certified in the U.S. to conform to the requirements of DHHS 21 CFR,
chapter 1 Subchapter J for Class I (1) laser products, and elsewhere is certified as a
Class I laser product conforming to the requirements of IEC 60825-1:2007.
Class I laser products are not considered to be hazardous. The laser system and unit
are designed so there is never any human access to laser radiation above a Class I
level during normal operation, user maintenance or prescribed service condition.
4
Worksheet to Record System Information
Use the following worksheet to record the information that is needed to install the
SCv2080 storage system.
Storage Center Information
Gather and record the following information about the Storage Center network and
the administrator user.
Table 1. Storage Center Network
Service Tag ________________
Management IPv4 address (Storage Center management
address)
___ . ___ . ___ . ___
Left Controller IPv4 address (Controller 1 MGMT port) ___ . ___ . ___ . ___
Right Controller IPv4 address (Controller 2 MGMT port) ___ . ___ . ___ . ___
Subnet mask ___ . ___ . ___ . ___
Gateway IPv4 address ___ . ___ . ___ . ___
Domain name ________________
DNS server address ___ . ___ . ___ . ___
Secondary DNS server address ___ . ___ . ___ . ___
Table 2. Storage Center Administrator
Password for the default Storage Center “Admin” user ________________
Email address of the default Storage Center “Admin” user ________________
5
iSCSI Fault Domain Information
For a storage system with iSCSI front-end ports, gather and record network
information for the iSCSI fault domains. This information is needed to complete the
Discover and Configure Uninitialized SCv2000 Series Storage Centers wizard.
NOTE: For a storage system deployed with two Ethernet switches, Dell
recommends setting up each fault domain on separate subnets.
See the Dell Storage Center SCv2080 Storage System Deployment Guide for
information about setting up iSCSI fault domains.
Table 3. iSCSI Fault Domain 1
Target IPv4 address ___ . ___ . ___ . ___
Subnet mask ___ . ___ . ___ . ___
Gateway IPv4 address ___ . ___ . ___ . ___
IPv4 address for storage controller module 1: port 1 ___ . ___ . ___ . ___
IPv4 address for storage controller module 2: port 1 ___ . ___ . ___ . ___
(Four port I/O card only) IPv4 address for storage
controller module 1: port 3
___ . ___ . ___ . ___
(Four port I/O card only) IPv4 address for storage
controller module 2: port 3
___ . ___ . ___ . ___
Table 4. iSCSI Fault Domain 2
Target IPv4 address ___ . ___ . ___ . ___
Subnet mask ___ . ___ . ___ . ___
Gateway IPv4 address ___ . ___ . ___ . ___
IPv4 address for storage controller module 1: port 2 ___ . ___ . ___ . ___
IPv4 address for storage controller module 2: port 2 ___ . ___ . ___ . ___
(4-port I/O card only) IPv4 address for storage controller
module 1: port 4
___ . ___ . ___ . ___
6
(4-port I/O card only) IPv4 address for storage controller
module 2: port 4
___ . ___ . ___ . ___
Additional Storage Center Information
The Network Time Protocol (NTP) and Simple Mail Transfer Protocol (SMTP) server
information is optional. The proxy server information is also optional, but it may be
required to complete the Discover and Configure Uninitialized SCv2000 Series
Storage Centers wizard.
Table 5. NTP, SMTP, and Proxy Servers
NTP server IPv4 address ___ . ___ . ___ . ___
SMTP server IPv4 address ___ . ___ . ___ . ___
Backup SMTP server IPv4
address
___ . ___ . ___ . ___
SMTP server login ID ________________
SMTP server password ________________
Proxy server IPv4 address ___ . ___ . ___ . ___
Fibre Channel Zoning Information
For a storage system with Fibre Channel front-end ports, record the physical and
virtual WWNs of the Fibre Channel ports in Fault Domain 1 and Fault Domain 2. This
information is displayed on the Review Front-End page of the Discover and
Configure Uninitialized SCv2000 Series Storage Centers wizard. Use this
information to configure zoning on each Fibre Channel switch.
See the Dell Storage Center SCv2080 Storage System Deployment Guide for
information about setting up Fibre Channel zoning.
Table 6. Physical WWNs in Fault Domain 1
Physical WWN of storage controller 1: port 1 ________________
Physical WWN of storage controller 2: port 1 ________________
7
(4-port I/O card only) Physical WWN of storage controller
1: port 3
________________
(4-port I/O card only) Physical WWN of storage controller
2: port 3
________________
Table 7. Virtual WWNs in Fault Domain 1
Virtual WWN of storage controller 1: port 1 ________________
Virtual WWN of storage controller 2: port 1 ________________
(4-port I/O card only) Virtual WWN of storage controller
1: port 3
________________
(4-port I/O card only) Virtual WWN of storage controller
2: port 3
________________
Table 8. Physical WWNs in Fault Domain 2
Physical WWN of storage controller 1: port 2 ________________
Physical WWN of storage controller 2: port 2 ________________
(4-port I/O card only) Physical WWN of storage
controller 1: port 4
________________
(4-port I/O card only) Physical WWN of storage
controller 2: port 4
________________
Table 9. Virtual WWNs in Fault Domain 2
Virtual WWN of storage controller 1: port 2 ________________
Virtual WWN of storage controller 2: port 2 ________________
(4-port I/O card only) Virtual WWN of storage controller
1: port 4
________________
(4-port I/O card only) Virtual WWN of storage controller
2: port 4
________________
8
Locating Your Service Tag
Your storage system is identified by a unique service tag and Express Service Code.
You can find the service tag on the back of the storage system chassis. Dell uses this
information to route support calls to the appropriate personnel.
Figure 1. Service Tag Location
Other Information You May Need
To install the storage system, you may need the following additional information.
NOTE: See the safety and regulatory information that shipped with your
Storage Center components. Warranty information is included as a separate
document.
• The Dell Storage Center SCv2080 Storage System Deployment Guide provides
information about cabling storage system hardware components and configuring
a new storage system using the Dell Storage Manager Client.
• The Dell Storage Manager Storage Center Administrator's Guide describes how
to use the Dell Storage Manager Client to manage a Storage Center.
• The Dell Storage Manager Administrator’s Guide describes how to use Dell
Storage Manager to manage multiple Storage Center systems.
9
Installation and Configuration
Before you begin installation, make sure that the site where you plan to install the
storage system has 208 V power from an independent source or a rack power
distribution unit with a UPS. (110 V power is not supported.)
In addition, verify that there is a 5U space in the lower 20U of the rack to install the
storage system. If you plan to install the storage system above the lower 20U of a
rack, a customer-provided mechanical lift must be used to avoid injury.
Safety Precautions
Always follow these safety precautions to avoid injury and damage to Storage Center
equipment.
If equipment described in this section is used in a manner not specified by Dell, the
protection provided by the equipment could be impaired. For your safety and
protection, observe the rules described in the following sections.
NOTE: See the safety and regulatory information that shipped with each
Storage Center component. Warranty information is included within this
document or as a separate document.
Installation Safety Precautions
Follow these safety precautions:
• Dell recommends that only individuals with rack-mounting experience install the
SCv2080 in a rack.
• You need at least two people to lift the storage system chassis from the shipping
box and three people to install it in the rack. The empty chassis weighs
approximately 62 kg (137 lbs).
• Make sure the storage system is always fully grounded to prevent damage from
electrostatic discharge.
• When handling the storage system hardware, use an electrostatic wrist guard
(not included) or a similar form of protection.
The chassis must be mounted in a rack. The following safety requirements must be
considered when the chassis is being mounted:
• The rack construction must be capable of supporting the total weight of the
installed chassis. The design should incorporate stabilizing features suitable to
10
Other manuals for SCv2080
3
Table of contents
Other Dell Storage manuals
Dell
Dell PowerVault 770N Technical manual
Dell
Dell PowerVault Storage Area Network User manual
Dell
Dell MD1400-16TB User manual
Dell
Dell PowerVault RD1000 User manual
Dell
Dell PowerVault RD1000 User manual
Dell
Dell PowerVault 130T DLT User manual
Dell
Dell Storage Center SCv2000 User manual
Dell
Dell PowerVault MD3060e Series Mounting instructions
Dell
Dell PowerVault MD3600i Series User manual
Dell
Dell PowerVault 220S User manual
Dell
Dell PS4100 Assembly instructions
Dell
Dell SC9000 User manual
Dell
Dell SCv2080 User manual
Dell
Dell EMC Integrated Data Protection Appliance... User manual
Dell
Dell PowerVault MD2412 User manual
Dell
Dell PowerVault DR4100 User manual
Dell
Dell PowerVault ML6000 Operating manual
Dell
Dell SC5020 User instructions
Dell
Dell PowerVault 110T LTO User manual
Dell
Dell EMC2 AX100 Series Instruction Manual
