Danfoss TP5001 series User manual
TP5001 Range
Electronic Programmable Room Thermostat
Danfoss Heating Installation Guide
TP5001
2
For a large print version of these instructions
please email customerservice.uk@danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other
printed material. Danfoss reserves the right to alter its products without notice. This also
applies to products already on order provided that such alterations can be made without
subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and all
Danfoss logotypes are trademarks of Danfoss A/S. All rights reserved.
Hereby, Danfoss A/S declares that the radio equipment type TP5001-RF + RX Receiver is in
compliance with directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address,
http://heating.danfoss.co.uk/xdoccat/14_CATC-J_MNU17497125_SIT313.html
Danfoss Heating 3
GR
TR
LV
LT
UA
RU
GB
Installation Guide
TP5001 Range
Electronic Programmable Room Thermostat
Index
1.0 Installation Guide .....................................................................................4
2.0 System Overview...................................................................................4-5
3.0 Installation ...................................................................................................6
3.1 Wiring - TP5001...................................................................................7
3.2 Battery Installation............................................................................7
3.3 Receiver Wiring (RF models)..........................................................8
3.4 Commissioning (RF versions only)...............................................9
4.0 Advanced Installer Programming Options...................................9
4.1 Entering Advanced Installer Programming Options.......... 10
TP5001
4
GR
TR
LV
LT
UA
RU
GB
Thermostat features TP5001 (A) TP5001-RF TP5001M (A)
Power supply 2 x AA/MN1500/LR
alkaline cells
230V, ±15%,
50Hz
Memory back-up Retained for life of product
Temperature Range
Sensing
5-30°C
Factory set calendar clock Automatic summer/winter time change
Switching action of
output relay
3(1)A,
10-230V N/A 3(1)A, 10-230V,
Type 1B
Transmission frequency
(RF models) N/A 433.92MHz N/A
Transmission range
(RF models) N/A 30m max. N/A
Remote sensor inputs
(A models only)
Can be set by installer for remote temperature
sensor, limit sensor, window contact or telephone
activated switch contacts
Dimensions (mm) 110 wide, 88 high, 28 deep
Design standard EN60730-2-9 (EN300220 for RF)
Rated impulse voltage 2.5kV
Ball hardness test 75°C
Control pollution
situation Degree 2
Temperature accuracy ±1°C
Time accuracy ±1 min. per month
1.0 Installation Guide
2.0 System Overview
Please Note:
This product should only be installed by a qualied electrician or
competent heating installer and should be in accordance with the
current edition of the IEEE wiring regulations.
Danfoss Heating 5
GR
TR
LV
LT
UA
RU
GB
Important note RF products: Ensure that there are no large metal
objects, such as boiler cases or other large appliances, in line of
sight between the transmitter and receiver as these will prevent
communication between thermostat and receiver.
ERP Class
The products represented within this document are classied according to,
and allow completion of, the Energy Related Product (ErP) Directive System
Package che and the ErP system data label. ErP Labelling obligation is ap-
plicable from 26th September 2015.
ERP Class Product Function and ErP Description
Additional
eciency
gain
V Modulating Room Thermostat, for use with
modulating heaters
An electronic room thermostat that varies the
ow temperature of the water leaving the heater
dependent upon measured room temperature
deviation from room thermostat set point. Control
is achieved by modulating the output of the
heater.
3%
ErP
5
Product
Class
TP5001
6
GR
TR
LV
LT
UA
RU
GB
3.0 Installation
• First, remove the wallplate from the back of the unit.
• From the top left hand corner of the wallplate, there must be
clearances of at least 15mm to the right, 15mm to the left,
30mm above and 100mm below in order to mount the plug-in
module.
• Thermostat and Remote Room Sensor:
Fix at a height of approximately 1.5m from the oor, away from
draughts or heat sources such as radiators, open res or direct
sunlight.
• Prior to mounting the unit the 2 DIL switches on the rear of the
unit have to be moved to the required position. The factory
presets are shown below.
1
2
Keyboard disabled
Reset disabled Reset enabled
Keyboard enabled
OFF ON
Sw. No.
30
cm
MIN 3
30m MAX
Danfoss Heating 7
GR
TR
LV
LT
UA
RU
GB
!Some existing thermostats will have a Neutral and/or Earth wire connected. These
are not required by the TP5001 (battery models) and must NOT be connected to
any TP5001 terminals. Instead they should be made electrically safe and coiled in
the recess at the back of the TP5001.
3.1 Wiring - TP5001
Models with remote sensor inputs
TP5001A and TP5001MA incorporate an input which can be used to
connect one of the following:
1) remote room temperature sensor (sold as accessory).
2) limit sensor, for example, oor temperature sensor (sold as
accessory).
3) window contacts, card reader contacts or teleswitch contacts.
See Installer Advanced Programming Options for set-up
instructions.
3.2 Battery Installation
When installing the batteries in the TP5001 and TP5001 RF please
ensure that the correct polarity is observed as per the markings on
the inside of the battery compartment.
Important: After installing the batteries press and release the RESET
button to start the unit. The display may appear blank until this is
done. Once the button is released the display will appear. All date,
time, programming and override settings are maintained for the life
of the product.
123
Output Connections,
all hard wired models
L
NDE
S1 S2
Remote Sensor
(A version only)
M 230V Models
TP5001
8
GR
TR
LV
LT
UA
RU
GB
IMPORTANT - To ensure that the factory programmes are set
and the micro-computer is operating correctly it is essential
that you press and hold the RESET button before you begin any
commissioning or programming.
Models with remote sensor inputs
Terminal block for remote control/sensing
is located on the circuit board above the
battery compartment.
RX1 RX2 & RX3
1234
ELECTRONICS
NL
COM ZONE
1 ON
ZONE
1 OFF
A
ELECTRONICS
BC123456
NLZONE
1 ON
ZONE
1 OFF
ZONE
2 ON
ZONE
3 ON
COM
TERMINAL 6
RX3 ONLY
3.3 RX Receiver Wiring (RF models only)
1) For mains voltage operated systems link terminal 2 to mains live supply.
2) Power supply to unit must not be switched by timeswitch.
S1/D
S2/E
S1/D
S2/E
Window or
teleswitch
contact
(NO or NC)
Teleswitch
contact (NC)
Window
contact (NC)
S1/D
S2/E
Congured for
remote room
sensor or limit
sensor
Congured for
window contact or
other contact such
as teleswitch
Congured for
window contact
and other contact
such as teleswitch
/
D
/
E
Remote
control
connections
Danfoss Heating 9
GR
TR
LV
LT
UA
RU
GB
3.4 Commissioning (RF models only)
If the thermostat and the receiver have been supplied together in
a combined pack, the units have been paired in the factory and no
commissioning is required (RX1 only).
To tune the RX receiver to the frequency of the thermostat signal, follow steps
1-5 below.
Step 1 TP5001-RF
Reset the unit by pressing the recessed reset
button.
Step 2 Press and hold V and + buttons for
3 seconds (TP5001-RF now transmits unique
signal continuously for 3 minutes).
Step 3 RX1
Press and hold buttons PROG and CH1 for 3 seconds until green light
ashes once.
Step 4 RX2 (if applicable)
Stat 1 - perform steps 1-3 and 5.
Stat 2 - perform steps 1-2 and then press
PROG and CH2 on RX2.
RX3 (if applicable)
Stat 1 - perform steps 1-3 and 5.
Stat 2 - perform steps 1-2 and then press PROG and CH2 on RX3 then
step 5.
Stat 3 - perform steps 1-2 and then press PROG and CH3 on RX3.
Step 5 TP5001-RF
Press V or Λto select temperature - the unit will revert back to operating
mode.
4.0 Installer Advanced Programming Options
TP5001 incorporates a number of advanced features which can be set by the
user. These are accessed via a User Advanced Programming Mode, please
refer to User Advanced Programming in the user instructions for details.
TP5001 incorporates an additional number of advanced features which can be
set by the installer to improve the operating eciency of the system and where
required, to change the user functionality of the product. These are accessed
via an Installer Advanced Programming Mode. These settings are optional and
need only be made if there is a demand for the enhanced functions.
TP5001
10
GR
TR
LV
LT
UA
RU
GB
Option 31 - Set lower limit of temperature range
This allows the lower limit of the thermostat setting
range to be electronically limited. Press +until Option
31 is displayed, use Vand Λto select required setting.
Setting 5 - 40°C (Factory setting is 5°C)
Option 32 - Enable O at lower limit
This enables an OFF function to be selected if a set
point below the lower limit is selected. Press +until
Option 32 is displayed, use Vand Λto select required
setting.
Setting 0 Disabled
Setting 1 Enabled (factory setting)
Option 30 - Set upper limit of temperature range
This allows the upper limit of the thermostat
setting range to be electronically limited. Press +
until Option 30 is displayed, use Vand Λto select
required setting.
Setting 40 - 5°C (Factory setting is 30°C)
4.1 Entering Installer Advanced Programming
mode
To access the Installer Advanced Programming Mode follow the
steps below:
a) Press and hold Vand PROG for 3 seconds to enter User Advanced
Programming, the display will change to gure opposite.
b) Press and hold V, Λand PROG for 5 seconds to enter Installer
Advanced Programming, the display will
change to gure opposite.
c) Use +and -keys to scroll backwards and
forwards between options then Vand Λkeys
to change the option settings. The ashing
digit on the right hand of the display indicates
the number of the selected option. The large
characters display the option value selected.
d) To return to RUN, press and hold PROG until colon blinks.
Other manuals for TP5001 series
7
Table of contents
Languages:
Other Danfoss Thermostat manuals
Danfoss
Danfoss RET2000 B User manual
Danfoss
Danfoss CET B-RF Operating instructions
Danfoss
Danfoss TP7000 Series User manual
Danfoss
Danfoss WP75-RF User manual
Danfoss
Danfoss ECL Comfort 310 User manual
Danfoss
Danfoss Link DBR User manual
Danfoss
Danfoss RET2000 B User manual
Danfoss
Danfoss ECtemp 316 User manual
Danfoss
Danfoss TP75 User manual
Danfoss
Danfoss Icon Master User manual
Danfoss
Danfoss GET B-RF Guide
Danfoss
Danfoss TP9000 Si User manual
Danfoss
Danfoss ECL Comfort 310, P330 User manual
Danfoss
Danfoss HC6110-3 User manual
Danfoss
Danfoss TP4 Assembly Instructions
Danfoss
Danfoss 140F1143 User manual
Danfoss
Danfoss ECtemp 531 User manual
Danfoss
Danfoss RET1000 B User manual
Danfoss
Danfoss ECL Comfort 310, A361 User manual
Danfoss
Danfoss KP Series User manual
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Honeywell
Honeywell CM721 user manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
