Danfoss ECtemp Touch User manual

Danfoss ECtemp Touch

Electronic Intelligent Timer

Thermostat

Installation Guide

electricheating.danfoss.com

Danfoss ECtemp Touch

Installation Guide2

1 Introduction

The Danfoss ECtemp Touch is an electronic programmable

timer thermostat used for controlling electrical oor heat-

ing elements. The thermostat is designed for xed instal-

lation only and can be used for both direct heating of the

entire room and for comfort heating of the oor. Among

others, the thermostat has the following features:

• A touchscreen display with backlight.

• An easy-to-follow menu-driven programming and

operation.

1 Introduction � � � � � � � � � � � � � � � � � � � � � 2

1.1 Technical Specications . . . . . . . . . . . 3

1.2 Safety Instructions . . . . . . . . . . . . . . . 5

2 Mounting Instructions � � � � � � � � � � � � � � � 6

3 Settings � � � � � � � � � � � � � � � � � � � � � � � � 9

3.1 Initial Settings. . . . . . . . . . . . . . . . . . 9

3.2 Forecast . . . . . . . . . . . . . . . . . . . . 13

3.3 Window Open . . . . . . . . . . . . . . . . 15

3.4 Maximum Floor Temperature . . . . . . . 16

4 Symbols � � � � � � � � � � � � � � � � � � � � � � � 18

5 Warranty� � � � � � � � � � � � � � � � � � � � � � � 19

6 Disposal Instruction � � � � � � � � � � � � � � � 19

Table of Contents

Danfoss ECtemp Touch

3Installation Guide

• An installation wizard with room/oor type-specic

setup.

• Support for multiple frame systems.

• Compatible with several 3rd party NTC sensors.

• Thermostat settings can be specied before instal-

lation and imported to the thermostat using a

web-generated code, or copied from a thermostat in a

similar installation.

• Smart access to thermostat settings after installa-

tion by using a web code interface for easy setup or

remote troubleshooting.

More information on this product can also be found at:

electricheating�danfoss�com

1�1 Technical Specications

Operation voltage 220-240 V~, 50/60 Hz

Standby power consumption Max. 0.40 W

Relay:

Resistive load

Inductive load

Max. 16 A / 3680 W @ 230 V

cos φ= 0.3 Max. 1 A

Sensing units NTC 6.8 kΩ at 25°C

NTC 10 kΩ at 25°C

NTC 12 kΩ at 25°C

NTC 15 kΩ at 25°C (Default)

NTC 33 kΩ at 25°C

NTC 47 kΩ at 25°C

Danfoss ECtemp Touch

Installation Guide4

Sensing values:

(Default NTC 15 K)

0°C

20°C

50°C

42 kΩ

18 kΩ

6 kΩ

Control PWM (Pulse Width Modulation)

Ambient temperature 0° to +30°C

Frost protection temperature 5°C to +9°C (default 5°C)

Temperature range Room temperature: 5-35°C.

Floor temperature: 5-45°C.

Max. oor: 20-35°C (if unrecov-

erable seal is broken then up to

45°C). Min. oor: 10-35°C, only

with combination of room and

oor sensor.

Sensor failure monitoring The thermostat has a built-in

monitoring circuit, which will

switch o the heating if the

sensor is disconnected or short-

circuited

Cable specication max. 1x4 mm2or 2x2,5 mm2

Ball pressure test temperature 75°C

Pollution degree 2 (domestic use)

Controller type 1C

Software class A

Storage temperature -20°C to +65°C

Danfoss ECtemp Touch

5Installation Guide

IP class 21

Protection class Class II -

Dimensions 85 x 85 x 20-24 mm

(in-wall depth: 22 mm)

Weight 103 g

Electrical safety and Electro-Magnetic Compatibility for

this product is covered by the compliance with the EN/IEC

Standard“Automatic electrical controls for household and

similar use”:

• EN/IEC 60730-1 (general)

• EN/IEC 60730-2-9 (thermostat)

1�2 Safety Instructions

Make sure the mains supply to the thermostat is turned o

before installation.

Important: When the thermostat is used to control a oor

heating element in connection with a wooden oor or

similar material, always use a oor sensor and never set the

maximum oor temperature to more than 35°C.

Please also note the following:

• The installation of the thermostat must be done by an

authorized and qualied installer according to local

regulations.

Danfoss ECtemp Touch

Installation Guide6

• The thermostat must be connected to a power supply

via an all-pole disconnection switch.

• Always connect the thermostat to continuous power

supply.

• Do not expose the thermostat to moisture, water, dust,

and excessive heat.

2 Mounting Instructions

Please observe the following placement guidelines:

Place the thermostat at a suitable height on the wall

(typically 80-170cm.).

The thermostat should not be placed in wet rooms.

Place it in an adjacent room. Always place the ther-

mostat according to local regulation on IP classes.

Do not place the thermostat on the inner side of an

exterior wall.

Always install the thermostat at least 50 cm. from

windows and doors.

Danfoss ECtemp Touch

7Installation Guide

Do not place the thermostat in a way that it will be

exposed to direct sunlight.

Note: A oor sensor enables a more accurate

temperature control and is recommended in all oor

heating applications and mandatory under wooden

oors to reduce the risk of over-heating the oor.

• Place the oor sensor in a conduit in an appropriate place

where it is not exposed to sunlight or draft from door

openings.

• Equally distant and >2cm from two heating cables.

• The conduit should be ush with the oor surface -

countersink the conduit if necessary.

• Route the conduit to the connection box.

• The bending radius of the conduit must be min 50mm.

Danfoss ECtemp Touch

Installation Guide8

Follow the steps below to mount the thermostat:

1. Open the thermostat:

Important: Do NOT press on the display screen when

removing the front part.

Press your ngers under the side of the front part and

pull toward you:

2. Connect the thermostat according to the connection

diagram.

The screen of the heating cable must be connected to

the earth conductor of the power supply cable by

using a separate connector.

Note: Always install the oor sensor in a conduit in the

oor.

IP21

T30

Dtouch

Mains

220-240V

50-60 Hz

Maximum

Load 16 (1) A

Sensor

Standby maximum 0.4W

NTC N

Danfoss ECtemp Touch

9Installation Guide

3. Mount and reassemble the thermostat.

• Fasten the thermostat to a socket or an exterior wall

box by driving the screws through the holes in each

side of the thermostat.

• Put the frame on.

• Click the display module back in place.

Important: Do NOT press on the display screen when click-

ing the display module back in place.

Initially main supply the thermostat for 15 hours to fully

charge the battery. The current time and day is then kept

for 24 hours if mains supply is o. All other settings are

stored permanently.

3 Settings

3�1 Initial Settings

Initial settings must be specied when the unit is activated

for the rst time:

Danfoss ECtemp Touch

Installation Guide10

1. Use the arrows in the right

side of the screen to go to

your language, and press to

select it. Then press in the

upper right corner to

conrm.

2. Press the hour numbers and

use the < and > arrows to set

the hour. Press to conrm.

3. Press the minutes numbers

and use the < and > arrows

to set the minutes. Press

to conrm. Press again to

go to the SET DATE screen.

4. Press the day, month and

year respectively and set the

date using the < and >

arrows and pressing to

conrm. When the date is

correct, press to conrm

on the SET DATE screen.

Other manuals for ECtemp Touch

Table of contents

Other Danfoss Thermostat manuals

Danfoss

Danfoss RET2001RF User manual

Danfoss

Danfoss CP10C User manual

Danfoss

Danfoss RT 14L User manual

Danfoss

Danfoss MTD Mounting instructions

Danfoss

Danfoss DEVIreg Multi User manual

Danfoss

Danfoss ECtemp 550 User manual

Danfoss

Danfoss living connect User manual

Danfoss

Danfoss TP5E User manual

Danfoss

Danfoss RT51 User manual

Danfoss

Danfoss RTW-RA User manual

Danfoss

Danfoss ST-D1 User manual

Danfoss

Danfoss C67 User manual

Danfoss

Danfoss FH-CWD User manual

Danfoss

Danfoss FP975 User manual

Danfoss

Danfoss ECtemp Smart User manual

Danfoss

Danfoss TP7001 series User manual

Danfoss

Danfoss CET B-RF Operating instructions

Danfoss

Danfoss TS715Si User manual

Danfoss

Danfoss WT-DR User manual

Danfoss

Danfoss TP5000 RF Si User manual

Danfoss

Danfoss TP5001RF User manual

Danfoss

Danfoss GreenCon RC-C2 User manual

Danfoss

Danfoss RT1-RF User manual

Danfoss

Danfoss TP5000 si range User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide