Danfoss BasicPlus2 WT-D User manual

Installation Guide

BasicPlus2WT-D & WT-P

Room Thermostats

VICUJ212 Danfoss Heating Solutions

Installation Guide BasicPlus2WT-D & WT-P

1. Installation Steps

User Guide can be downloaded from: heating.danfoss.com.

1. Installation must be done by an authorised

electrician.

2. The room thermostat should be installed at approx.

1.5 m above oor and where the eects of sunlight,

draught or other heat sources (eg. TV’s) are avoided,

see g. 1.

3. First of all, carefully remove the cover, see g. 2.

4. Connect the wire before mounting the back plate to

the wall box using the enclosed screws. Then mount

the cover to the back plate, see g 3.

2. Wiring

Dimensions, see g. 4. Wiring diagram, see g. 5 (S1, S2:

oor sensor terminals).

WT-D/P is often used with Danfoss TWA actuator.

Depending on the conditions of power location and

actuator type (NC or NO), the wiring between room

thermostat and actuator is dierent.

Follow the illustrations to complete the wiring:

1. When power supply location is close to room

thermostat:

• Connect to actuator TWA 230 V NC type,see g. 6.

• Connect to actuator TWA 230 V NO type, see g. 7.

Danfoss Heating Solutions VICUJ212

Installation Guide BasicPlus2WT-D & WT-P

2. When power supply location is close to actuator:

• Connect to actuator TWA 230 V NC type, see g. 8.

• Connect to actuator TWA 230 V NO type, see g. 9.

3. Error codes

Display Description

E1 Room sensor failure

E2 Floor sensor failure

4. Notes

1. Correct wiring is essential; using instrument to con-

rm L and N before wiring is recommended.

2. Don’t remove too much of the insulation cover from

the wire to avoid short circuit caused by the naked

wire touching the metal 86 size mounting wall box.

3. Don’t let the screw press or touch the wire when

using screw to x room thermostat in wall box. A

short-circuit risk exists if the wire insulation cover is

damaged by the screw, and if the naked wire con-

nects with the screw.

4. If walls must be painted, mount the room thermostat

after painting, to avoid dust or paint material pen-

etrating the room thermostat and thus damaging

the PCB.

VICUJ212 Danfoss Heating Solutions

Installation Guide BasicPlus2WT-D & WT-P

5. The max load of relay is 3 A (resistive) or 1 A (induc-

tive, such as pump, motor). The relay will be dam-

aged if the load exceeds the limit.

6. Don’t cover the thermostat, for instance by hanging

towels directly in front of it.

7. The room thermostat should be connected to the

corresponding loop actuator in individual room

temperature control.

5. Technical Specications

Feature Description

Approval CE Marking, EN60730

Ambient temperature -10 - 60° C

IP Class 30

Max. load, inductive <1 A

Max. load, resistive <3 A

Power consumption 2 W

Power supply 85-250 Vac, 50/60 Hz

Room temp. set range 5 - 35° C

Floor temp. set range 20 - 45° C

Shell material ABS + PC

Danfoss Heating Solutions VICUJ212

Installation Guide BasicPlus2WT-D & WT-P

Fig. 1

1.5 m

Fig. 2

Fig. 3

VICUJ212 Danfoss Heating Solutions

Installation Guide BasicPlus2WT-D & WT-P

Fig. 4

86.0

24.516.0

50.0

Fig. 5

230 V

Fig. 6

230 V

TWA

230V

WT-D/P

L NO NC N S1 S2

Danfoss Heating Solutions VICUJ212

Installation Guide BasicPlus2WT-D & WT-P

Fig. 7

230 V

TWA

230V

WT-D/P

L NO NC N S1 S2

Fig. 8

230

V ~

TWA

230V

WT-D/P

L NO NC N S1 S2

Fig. 9

230

V ~

TWA

230V

WT-D/P

L NO NC N S1 S2

VICUJ212 Produced by Danfoss Floor Heating Hydronics 03/2015

Danfoss can accept no responsibility for possible errors in catalogues, brochures and

other printed material. Danfoss reserves the right to alter its products without notice.

This also applies to products already on order provided that such alterations can be

made without subsequential changes being necessary in specications already agreed.

All trademarks in this material are property of the respective companies. Danfoss and

This manual suits for next models

Table of contents

Other Danfoss Thermostat manuals

Danfoss

Danfoss ECtemp 610 User manual

Danfoss

Danfoss ECtemp 316 User manual

Danfoss

Danfoss TP5E User manual

Danfoss

Danfoss TP5000-RF Operating instructions

Danfoss

Danfoss Basic Plus2 User manual

Danfoss

Danfoss TP5000 si range User manual

Danfoss

Danfoss Icon Master User manual

Danfoss

Danfoss CET2000B-RF User manual

Danfoss

Danfoss RET2001RF User manual

Danfoss

Danfoss RT 101 User manual

Danfoss

Danfoss TP4000 Range User manual

Danfoss

Danfoss DEVI DEVIreg 330 User manual

Danfoss

Danfoss HC8000 Series User manual

Danfoss

Danfoss TP9000 User manual

Danfoss

Danfoss TP5001 series User manual

Danfoss

Danfoss Icon Master User manual

Danfoss

Danfoss TP75H Operating manual

Danfoss

Danfoss RT52 User manual

Danfoss

Danfoss DEVIreg 530 User manual

Danfoss

Danfoss Icon Master User manual

Danfoss

Danfoss ECtemp 531 User manual

Danfoss

Danfoss ECL Comfort 310 User manual

Danfoss

Danfoss Icon Master Controller 24 V User manual

Danfoss

Danfoss TP7001 series User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide