Danfoss IKORE B User manual
Revision history Table of revisions
Date Changed Rev
May 2021 Battery information updated, technical information corrected 0201
January 2019 Rebranded to Danfoss Power Solutions 0101
User Manual
IKORE B Transmitter
2 | ©Danfoss | May 2021 BC292582855621en-000201
Safety instructions General safety....................................................................................................................................................................................4
Safety warnings.................................................................................................................................................................................4
FCC rules..............................................................................................................................................................................................5
Technical description Dimensions and identification.....................................................................................................................................................6
Startup..................................................................................................................................................................................................7
IKORE B detailed description........................................................................................................................................................8
Maintenance Maintenance tips..............................................................................................................................................................................9
Troubleshooting 2.4GHz................................................................................................................................................................9
Charger and battery Charger and battery......................................................................................................................................................................10
BC70K and BT11K specifications...............................................................................................................................................10
BC70K Battery Charger Set-up.................................................................................................................................................. 10
BC70K Charger LEDs Status .......................................................................................................................................................11
Battery Charging Recommendations..................................................................................................................................... 11
BC70K Battery Charger Dimensions........................................................................................................................................12
User Manual
IKORE B Transmitter
Contents
©Danfoss | May 2021 BC292582855621en-000201 | 3
IKORE B General Safety
The following safety instructions must be read carefully to install and use the product properly, and to
keep it in perfect working condition, and to reduce the risk of misuse.
•Strictly adhere to the installation instructions contained in this document.
•Make sure that professional and competent personnel carry out the installation.
•Ensure that all site and prevailing safety regulations are fully respected.
•Make sure that this document is permanently available to the operator and maintenance personnel.
•Keep the transmitter out of reach of non-authorized personnel.
•Remove the transmission key when the set is not in use.
•Check each working day the STOP button and other safety measures. When in doubt, press the STOP
button.
•Whenever several sets have been installed, make sure the transmitter is the right one. Identify the
machine controlled on the label for this purpose on the transmitter or by using the display (in case it
has one).
•Service the equipment periodically.
•When carrying out repairs, use spare parts supplied by Danfoss only.
W
Warning
Potential damage to the operator or the product. Do not use this product on machines in potentially
explosive atmospheres unless the model is ATEX/RATEX certified to work in such conditions.
IKORE B Safety Warnings
Potential damage to operator and product.
Follow the guidelines below to reduce risk of injury to the operator and the product.
•Use the device with the manufacturer's battery and battery charger (if applicable).
•Only allow qualified personnel to operate the equipment.
•Always set the STOP button in the off position when not in use.
•Always press STOP before plugging in tether cable (if applicable).
•Remove the Tether connection on the transmitter First (if applicable).
•Do not operate product when visibility is limited.
•Make sure product is compatible with the machine.
•Avoid knocking or dropping the product.
•Do not use the product if a failure is detected.
Changes or modifications not approved by Danfoss can void the user's authority to operate this product.
Quick reference precautions
Tx Cr 1
Cr 1
Remove the EEPROM in order
to disable the transmitter When in doube, press the
STOP button
Make sure the transmitter
works with the machine
to be handled
Do not use the set when
visibility is limited Avoid knocking or dropping
the set
User Manual
IKORE B Transmitter
Safety instructions
4 | ©Danfoss | May 2021 BC292582855621en-000201
FCC rules
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules.
Changes or modifications not expressly approved by the manufacturer can void the user's authority to
operate the equipment.
To comply with FCC RF exposure compliance requirements, this device and its antenna must not be
collocated with, or operating in conjunction with, any other antenna or transmitter, may not cause
harmful interference, and must accept any interference received, including interference that may cause
undesired operation.
The limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy, and if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
W
Warning
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
User Manual
IKORE B Transmitter
Safety instructions
©Danfoss | May 2021 BC292582855621en-000201 | 5
IKORE dimensions and identification
Dimensions in mm
175
68
47
56
4
6
1
2
3
4
5
3
8
7
1. Status LEDs
2. Hoist selection LEDs
3. Maneuver push buttons
4. STOP button
5. External and extractable EEPROM module
6. Rechargeable Li-Ion batteries BT11K
7. START push button
8. Hoist selection push button
User Manual
IKORE B Transmitter
Technical description
6 | ©Danfoss | May 2021 BC292582855621en-000201
IKORE startup
1. Insert the EEPROM and fully charged rechargeable BT11K battery.
2. Push and pull out the STOP button.
The status LED will blink in blue until it reaches the stand-by mode and then it will turn into a fixed
blue.
RX
III
RX
I /I+II /II
* Data sheet
III
[1]
III
3. Press the start button.
The LED will blink green until the transmitter is linked with the receiver.
RX
III
RX
I /I+II /II
* Data sheet
III
[1]
III
When the receiver confirms the link, the status LED will turn to a fixed green and the system is now fully
operational.
When the system controls two hoists, there will be a push button for the selection of individual or joint
control. I and II LEDs will show their selection.
User Manual
IKORE B Transmitter
Technical description
©Danfoss | May 2021 BC292582855621en-000201 | 7
IKORE B detailed description
Technical data
Description Value
Stop function Cat. 3-Ple EN12849-1 and SIL 3 IEC 61508 / IEC 62061
Ingress Protection rating IP65/NEMA4
Anti-condensation system N/A
Frequency band 2405MHz to 2475MHz 20dBm/100mW
Main mechanisms (maximum) Push button (7) + START+ STOP
Range (Normal Conditions) 100m
Auxiliary mechanisms N/A
Removable EEPROM External
Battery model BT11K
Battery life 8hr (100% duty cycle)
Operating temperature range -20 °C to 70 °C (-4 °F to 158 °F)
Storage Temperature Range (24h) -25ºC to 75ºC (-13ºF to 167ºF)
Storage Temperature Range (long periods) -25ºC to 55ºC (-13ºF to 131ºF)
Relative Humidity max. 95% without condensation
Weight (with battery) 315 grams
Dimensions LxWxH mm 174.5x68x56
Harness Hand strap/shoulder strap
Display N/A
Cable connector N/A
Range limiter N/A
Associated receivers R11
User Manual
IKORE B Transmitter
Technical description
8 | ©Danfoss | May 2021 BC292582855621en-000201
IKORE B maintenance tips
This product is designed for use in an industrial environment that may shorten the product's lifespan. Use
these tips to maximize the lifespan of the product.
•Use the hook/belt provided with the transmitter to prevent the transmitter from falling
•Do not clean the transmitter with solvents or pressurized water; use a damp cloth or soft brush for
cleaning
•If the push buttons show signs of deterioration, contact the Authorized Technical Service for repair
•Check if the battery contacts are correct, otherwise replace them.
•Ensure that the product is supplied with AAA alkaline batteries or has a rechargeable battery
•Be sure to recharge or replace battery regularly
Maintenance tips quick reference
Troubleshooting 2.4GHz
Color and frequency Pulse frequency Description Action
Blue | fast pulses Starting the system; establishing communications with
radio and EEPROM Wait
Blue | continuous Stand-by mode. Set up system, waiting user's action Press START to enter operation
mode
Green | fast pulses Attempting to link with the receiver and waiting its
answer Wait
Green | continuous Working Operate
Green | slow pulses Latency; no action has been taken for some time Press START to return to operation
mode
Red | slow pulses EEPROM module missing or corrupt Check EEPROM and reprogram if
necessary
Red | double pulses Radio error; radio communications error Replace transmitter
Red | continuous General hardware failure Replace transmitter
Orange | slow pulses Critical battery signal Replace batteries with charged ones
Orange | double pulses Activated maneuver Release maneuver
User Manual
IKORE B Transmitter
Maintenance
©Danfoss | May 2021 BC292582855621en-000201 | 9
Charger and battery
Disposal note:
This symbol on the product indicates that it may not be disposed of as household waste.
It must be handed over to the applicable take-back scheme for the recycling of electrical equipment.
•Dispose of the product through channels provided for this purpose.
•Comply with all local and currently applicable laws and regulations.
BC70K and BT11K specifications
BC70K battery charger
Specification Value
AC power supply 110 – 230 V, 50/60 Hz, ± 10%, automatic switching
DC power supply, nominal 12 – 24 V
BT11K battery
Specification Value
Voltage 3.7 V
Capacity 1130 mAh Li-Ion
Charging temperature 0°C to 45°C
Discharge temperature -20°C to 60°C
Charging mode Fast (<2.5 h) and intelligent
Weight 23 g
BC70K Battery Charger Set-up
The battery charger has two charging compartments that can simultaneously charge two BT11K
batteries. Use the information below to set up the BC70K battery charger.
1. Connect the charger to a power source using the cable provided.
The red LED will switch on if the charger is properly connected.
2. Place the batteries in the charger.
3. Optional: If charging two batteries, wait at least five seconds before inserting the second battery into
the compartment.
W
Warning
Possible damage to battery.
Be sure to charge batteries in environments with temperatures over 0°C.
User Manual
IKORE B Transmitter
Charger and battery
10 | ©Danfoss | May 2021 BC292582855621en-000201
Other manuals for IKORE B
1
Table of contents
Other Danfoss Remote Control manuals
Danfoss
Danfoss TM70 User manual
Danfoss
Danfoss 102E7 User manual
Danfoss
Danfoss IKORE User manual
Danfoss
Danfoss SET3M User manual
Danfoss
Danfoss 103E7 Assembly Instructions
Danfoss
Danfoss MP08A User manual
Danfoss
Danfoss T70 1 HALL User manual
Danfoss
Danfoss CF-RC User manual
Danfoss
Danfoss R06 User manual
Danfoss
Danfoss MPCAN User manual
Danfoss
Danfoss Ikompact User manual
Danfoss
Danfoss R13 F User manual
Danfoss
Danfoss CF-RC User manual
Danfoss
Danfoss IKP1000 User manual
Danfoss
Danfoss IK2 User manual
Danfoss
Danfoss Ikargo2 User manual
Danfoss
Danfoss CF-RC User manual
Danfoss
Danfoss Ikompact User manual
Danfoss
Danfoss WS103 User manual
Danfoss
Danfoss 175G9004 User manual
