Danfoss SFA 10 Manual

027R9981

Fig. 3. Fixation/ Cap removalFig. 2. Unseal SFA

Fig. 1. Repair Kit Content

1 3

25 mm (1”)

Service guide / Repair kit installation

Safety relief valves

SFA 10, SFA 10H

AN352739267283en-000101 | 1

Fig. 5. Unscrew inlet connector

Fig. 4. Loosen locknut/ adjustment screw

6 mm

35 mm

18 mm

AN352739267283en-000101 | 2

Fig. 6. Cone-spindle removal Fig. 7. Cone-spindle replacement

1 3

AN352739267283en-000101 | 3

Fig. 8. Insert Cone-spindle assembly

Fig. 10. Reset adjustment screw Fig. 11. Calibration Fig. 12. Fasten lock nut

Fig. 9. Reinstall inlet connector

Calibration by authorized

personel

225 Nm

166 ft lb

30 Nm

22.1 ft lb

AN352739267283en-000101 | 4

90 Nm

66.4 ft lb

Fig. 13. Fasten cap Fig. 14. Reseal SFA

In addition to the instructions below, all inspection, repair and recalibration must comply with all local laws and

requirements.

Inspection

When due for service or after the safety valve has been activated it is recommended to disassemble and clean the valve

seat for dirt and particles. The valve must not be disassembled while installed/in operation. Servicing of the valve is only

allowed when valve is dismantled. Apply torque to the inlet body hexagon only and not on the valve body when disman-

tling the safety valve from the changeover valve or pipe ﬁtting. All external sealings must be changed during service using

the 148F3068 SFA 10(H) / DSV 10 inspection kit.

Corrosion

Dust, dirt, corrosion or sticky medias on moving and guiding parts may inﬂuence the valve function negatively. If any part

(including the spring) inside the valve are corroded, the valve should be fully replaced. Dirt and particles must be fully

removed. In extreme environments it is recommended to use a valve with bellow instead. This will protect the valve from

refrigerant contaminated with dirt and particles.

Springs

Observe! When cleaning or replacing the spring, it is very important that the exact same spring type is being used. The

spring type can be identiﬁed by the color of ﬁrst windings. Even though it may be possible to set the correct pressure with

a wrong spring, the opening and closing characteristics may be compromised and may lead to reduced lift, leading to lack

of valve capacity and increased system pressure, increased blowdown, leading to extraordinary loss of charge

Temperature ageing

The O-ring material ages when exposed to atmosphere and/or long-term high temperatures. Max. temperature is 100 °C

(212 °F) during activation. If this temperature is exceeded the valve may not reseat perfectly leading to loss of refrigerant.

At static temperatures above 60 °C (140 °F) the lifetime of the O-ring will be gradually reduced, and the valve should be

serviced more frequently, using Danfoss SFA 10(H) repair kit.

Repairing the SFA 10(H)

The Cone and O-ring can be replaced using one the Danfoss SFA 10(H) repair kits. Observe that the repair kits are covering

diﬀerent set pressure ranges and that purchased repair kit matches the set pressure of the valve to be repaired.

Recalibration and leak test

To verify the valve function after service or inspection following tests should be done by authorized personnel. Danfoss

cannot be held responsible for correct function / set pressure after recalibration.

AN352739267283en-000101 | 5

Fig. 1: Repair Kit content

1. Cone-spindle

2. O-ring inlet connector

3. O-ring cap

Fig. 2: Unseal SFA

1. Cut wire to unseal SFA

Note: Cutting the wire will make any warranty void

Fig. 3: Fixation/ Cap removal

1. Fix the SFA in a vice at this area

2. Unscrew the cap (25 mm or adjustable wrench)

Fig. 4: Loosen locknut/ adjustment screw

1. Loosen locknut 1/2 turn counterclockwise (18 mm socket wrench)

2. Loosen adjustment screw 15-20 turns counterclockwise (Allen key 6 mm)

Fig. 5: Unscrew inlet connector

1. Unscrew inlet connector (35 mm – 6 edge socket wrench or 36 mm – 12 edge socket wrench)

Fig. 6: Cone-spindle removal

1. Carefully take out the insert

2. Place on soft and clean surface

Note: Inspect and clean the valve seat and spring for dirt and particles. Replace the valve if the spring is corroded.

Fig. 7: Cone-spindle replacement

1. Remove loose parts

2. Replace the Cone-spindle

3. Re-assemble loose parts

Fig. 8: Insert Cone-spindle assembly

1. Carefully insert new Cone-spindle assembly

Fig. 9: Reinstall inlet connector

1. Replace O-ring

2. Tighten inlet connector to torque 225 Nm (166 ft lb)

Fig. 10: Reset adjustment screw

1. Fasten adjustment screw 15-20 turns clockwise

Fig, 11: Calibration

Calibration by authorized personel. The following steps (ﬁg.12 to ﬁg.14) must be done by authorized personel

only

Fig. 12: Fasten lock nut

1. Fasten lock nut to torque 30 Nm (22.1 ft lb)

Fig. 13: Fasten cap

1. Replace O-ring

2. Fasten cap to torque 90 Nm (66.4 ft lb)

Fig. 14: Reseal SFA

1. Reseal SFA

AN352739267283en-000101 | 6

This manual suits for next models

Table of contents

Other Danfoss Control Unit manuals

Danfoss

Danfoss AB-QM Series User manual

Danfoss

Danfoss VLT AutomationDrive FC 360 User manual

Danfoss

Danfoss AFQM User manual

Danfoss

Danfoss HFI User manual

Danfoss

Danfoss ASV-PV User manual

Danfoss

Danfoss EVUL 1 User manual

Danfoss

Danfoss PVG-EX 32 Manual

Danfoss

Danfoss EKE 1P User manual

Danfoss

Danfoss GBC 6s H User manual

Danfoss

Danfoss Icon Master User guide

Danfoss

Danfoss Akva Lux II TDP-F User manual

Danfoss

Danfoss MCX-RTU User manual

Danfoss

Danfoss AMZ 112 User manual

Danfoss

Danfoss PVG 128 User manual

Danfoss

Danfoss TCBE User manual

Danfoss

Danfoss ICF 50-4 User manual

Danfoss

Danfoss AK-CM 102 User manual

Danfoss

Danfoss SVA-S 6-10 User manual

Danfoss

Danfoss PVG 100 User manual

Danfoss

Danfoss MSV-C User manual

Danfoss

Danfoss PVG 100 Building instructions

Danfoss

Danfoss SVA-S SS 15 User manual

Danfoss

Danfoss SFV Series User manual

Danfoss

Danfoss MSV-F2 DN Series User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual