Danfoss DHP-A User manual

VMBMF302

Installation instruction

Outdoor unit

DHP-A, DHP-AL

Contents

1 Installing the outdoor unit ...........................2

1.1 Check the delivery ..........................................2

1.2 Assembling the stand .......................................2

1.3 Preparing the outdoor unit ..................................2

1.4 Assembling the outdoor unit on the stand . . . . . . . . . . . . . . . . . . .3

1.5 Assembling the front cover ..................................3

1.6 Assembling the cover and cover plate .......................4

1.7 Assembling the defrost sensor...............................6

2VMBMF302

1 Installing the outdoor unit

It is essential that the outdoor unit is installed by two people.

1.1 Check the delivery

The outdoor unit is delivered as three items:

• the outdoor unit, on a wooden pallet

• a box containing the stand, adjustable feet and all the necessary screws

• aboxcontainingcovers

The following tools are required for assembly and installation:

• Wrench, or equivalent, 10 mm

• Wrench, or equivalent, 13 mm

• Screwdriver, or equivalent, torx TX25

• Cross head screwdriver

• Drill bit Ø 3 mm

• MillingcutterØ 6 mm, or equivalent

• Drill

Check that the following screws have been supplied:

• 8 x M6x10, hex screw

• 4 x M6x10, hex screw

• 5 x M6x15, torx TX25

• 2 x panel screws, crosshead

1.2 Assembling the stand

1. Screw the two horizontal struts together (1) using the two ends (2) as illustrated below. Use 8 x M6x10 screws. The bent

edges of the horizontal struts must be facing upwards and inwards.

Figure 1: Assembling the stand.

2. Screw the adjustable feet (3) into the holes under the ends.

1.3 Preparing the outdoor unit

While the outdoor section remains on the pallet it should be prepared for placing on the stand. Carry out the following:

3. There are three M6x20 screws on the lower edge of the outdoor unit. Unscrew them so that 2-3 mm of the thread

remains. Use a torx TX25 screwdriver, or equivalent.

4. Raise the outdoor unit. NOTE! Do not lift the side plates.

5. Remove the side plates. They are held in place by clamps and so are removed by pulling outwards.

6. Remove all four screwed lifting eyes. Use a 13 mm wrench, or equivalent.

Slit

Bent edge

VMBMF302

1.4 Assembling the outdoor unit on the stand

7. Lift the outdoor unit into the place on the stand.

Figure 2: Lift the outdoor unit onto the stand.

8. Screw the outdoor unit onto the stand. Use 4 x M6x20 screws. It may be necessary to push and pull the stand slightly in

order to get the screw holes to align.

9. Reinstall the side panels.

1.5 Assembling the front cover

⚠ Leave the transport protection on the corners of the front panel in place during installation to prevent scratches on the

outer section.

10. Hook the lower edge of the front cover onto at least one of the three screws in the bottom edge of the stand.

11. Secure the upper edge of the front panel temporarily in the centre hole. Use 1 x M6x15 torx TX25.

12. Align all the three screws in the lower edge.

13. Screw the three screws in the lower edge fully. Use a torx TX25 screwdriver, or equivalent.

4VMBMF302

14. Secure the upper edge of the front cover. Use 3 x M6x15 torx TX25.

Figure 3: Secure the front cover.

15. Remove the transport protection on the four corners of the front panel.

Figure 4: Transport protection.

1.6 Assembling the cover and cover plate

16. Hook the cover at the front edge on the front cover.

Figure 5: Hook the front cover into place.

VMBMF302

17. Secure the cover using a screw on each side. Use 2 x cross head screws.

If the cover does not align with the side cover plates it may be necessary to drill new Ø 3 mm holes:

•Mark for the new holes

•Lift off the cover

•Drill the holes

•Install and screw the cover into place

Figure 6: Screw the front cover into place.

18. Hook the cover onto the stand.

Figure 7: Hook the cover into place.

6VMBMF302

1.7 Assembling the defrost sensor

Figure 8: Hook the defroster sensor into place.

18. Slide the mounting for the defroster sensor into the hole on the reverse of the outdoor unit until it hooks into place on

the edge.

19. Secure the defroster sensor at the bottom of the mounting using a cable tie.

The outdoor unit is now mounted and can be adjusted on the site where it should be set up.

Other manuals for DHP-A

This manual suits for next models

Table of contents

Other Danfoss Control Unit manuals

Danfoss

Danfoss 103E5 Assembly Instructions

Danfoss

Danfoss USV-I User manual

Danfoss

Danfoss PVG 120 User manual

Danfoss

Danfoss RLV-X User manual

Danfoss

Danfoss MSV-F Plus DN 15 User manual

Danfoss

Danfoss EKC 102D User manual

Danfoss

Danfoss Akva Lux II TDP-F User manual

Danfoss

Danfoss PM 5-65 User manual

Danfoss

Danfoss ESMD User manual

Danfoss

Danfoss SVA-S 15-200 Series User manual

Danfoss

Danfoss PVG 32 User manual

Danfoss

Danfoss Icon Master User guide

Danfoss

Danfoss AMZ 112 User manual

Danfoss

Danfoss ASV-PV series User manual

Danfoss

Danfoss PVG 128 User manual

Danfoss

Danfoss REG-SA SS 15-40 User manual

Danfoss

Danfoss SFV Series User manual

Danfoss

Danfoss PVG-EX 32 Manual

Danfoss

Danfoss EKC 102A User manual

Danfoss

Danfoss VFS 2 User manual

Danfoss

Danfoss MSV-F2 DN15 - 400 User manual

Danfoss

Danfoss XGE-4C User manual

Danfoss

Danfoss DSV 1 User manual

Danfoss

Danfoss VACON NXP IP00 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual