Dancover Arched PE User manual

04-09-2014-QJ

4x8x2,5x3,8m

Storage tent Arched PE

Manual

Safety Advice

Attention

In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is

your responsibility to comply with local rules and regulations and to ensure that the

marquee/tent is assembled correctly.

In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is

safely secured and that the marquee/tent does not cause damage to others.

close to the tent.

The marquee/tent must be safely secured. We recommend you secure your marquee/tent

with straps and pegs as soon as it is assembled.

Make sure to check if the marquee/tent is covered by your home contents

insurance.

Marquees/tents must be evacuated under extreme weather conditions.

In the event of snow always remove snow from the roof of the marquee/tent regularly to

prevent snow from building on the roof as heavy snow can cause the marquee/tent to

collapse.

In the event of rain there is a risk of rain puddles building up on top of the roof of the

marquee/tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility

to ensure rain puddles do not build up. As a precaution, make sure the roof of the

marquee/tent is stretched out properly and adequately over the side frames of the

marquee/tent and remove rain water regularly.

Do not unpack or repack your marquee/tent in freezing temperatures. In case of

temperatures below zero always unpack and repack your marquee/tent indoors to avoid

the risk of cracking parts.

The marquee/tent must be totally dry before you repack and store it to avoid mildew.

Warranty Information

Please visit dancovershop.com for information on warranty.

Please always check our website for the latest safety advice and manuall.

This structure is not tested for snow and wind loads. We always recommend that

you remove snow from the roof. This is a none-permanent structure.

Congratulations on your purchase of our instant shelter. This unit is a combination

of excellent manufacturing and design. It is comprised of a rigid frame and a durable

cover. For easy assembly, we have marked all the parts with codes, with proper

installation, use and maintenance, your unit will provide many years of good and

suitable service.

Tools required

The following hand tool will be needed for proper Installation of your new building:

12mm,14mm，and 17mm Open End Wrenches,

12mm, 14mm, 17mm Sockets or Box Wrench,

Large Flat Head Screwdriver,

2lb maul or Sledgehammer

4 Foot Level 14’Step Ladder

Stake &String for aligning Base Plates &Frame

Assembly procedure

1. Prepare location and place all unit boxes near location sight. Perform an inventory

check before beginning, to be certain all components are available for installation.

2. Secure base plate flanges to base surface.

3. Assemble every group of arch.

4. Begin frame assembly with front end arch, first interior arch, purlins, etc.

5. Add to assemble other groups of arches.

6. Install main cover over frame.

7. Install end cover over end panels.

Read all the detailed instructions and notices in the following assembly

instructions!

Maintenance and care

Annually or more often, the unit should be completely inspected internally and externally to make

certain the unit remains properly installed and secured .Particular attention should be paid to:

Hardware-check all carriage bolts and hardware connectors to be certain they are in place and

tightened.

Weather trends, the unit will strain against the base plate flange under windy conditions, pegs

hardware, connection to frame members should be maintained tight and depth of pegs should be

checked to be certain they remain deeply and firmly set.

Snow Accumulation -All snow accumulation on the main cover should be removed as soon as

possible. Tap the main cover from the inside with a broom or soft brush to clear cover.

Main Cover Lacing-the poly rope that secures the main cover to the bottom rail of the frame

assembly should be checked, and adjusted as needed. The tension on the main cover should be

uniform from end and side to side. Rope ends must be tied off onto the frame members at the ends

on each side.

Cleaning -cover and doors can be cleaned with a mixture of light detergent and water. A soft

bristle brush with the mixture can be used to loosen any hard dirt, mold, or buildup on the cover.

After cleansing, the cover should be rinsed thoroughly to avoid any chemical reaction from

residual detergent. Allowing dirt and debris to sit on cover over an extended time will damage

cover irreparably.

Severe Weather-in preparation for inclement weather, completely secure the door of your buildings

portable building.Allowing wind to enter end lifts the

Thanks again for choosing this quality product. The following is the

detailed assembly instructions for you starting the assembly.

Part List

ytitnauQnoitpircseDedoCtraP

5ebutdevrucfoorpoT1

6ebutdevrucfooR2

4raerdnatnorftaebutdevrucfooRA2

6ebutllawediS3

4raerdnatnorftaebutllawediSA3

02ebutlatnozirohdnanilrupfooR4

2renrocniegnalfesaBL5

2renrocniegnalfesaBR5

3llawedisrofegnalfesaBL6

3llawedisrofegnalfesaBR6

7 Base flange for standing legs in the front panel 4

8 Upper vertical tube for front and rear door 4

9 Lower vertical tube for front and rear door 4

4lenapraerdnatnorfedisehtrofmaeB01

4ebuttroppusgnitnalS11

8ebuttroppusgnitnalsrofpilcebuTA11

stes2ebutgninoisnetrevocfoorrewoL21

13 Bottomtensioningtube of front and back cover 4

14 Pole for help openingand closing the door 1

83gepekatS51

15ADoor cover Stake Peg 2

01tehctarnwodeiT61

21ebutgninoisnetrofpaccitsalP71

18 Hexagon bolt M10x75 80

19 Carriage bolt M10x85 27

20 Hexagon bolt M10x30 12

21 Hexagon bolt M10x85 8

21AHexagon bolt M10x12 20

22 Nylon bands for tensioning roofcover 10

23 Fastening rope for front cover and the of roof cover 6

24 Roof cover 1

25 Front cover 2

04-09-2014-QJ

Figure 1

Sketch of Model132612 Size:W4*L8*H3.8M

Figure 2 Sketch of parts

Part no 1, 5 pcs

Part no 2, 6 pcs

Part no 3, 6 pcs

Part no 8, 4 pcs

Part no 4, 20 pcs

Part no 9, 4 pcs

Part no 10, 4 pcs

Part no 11, 4 pcs

Part no 2A, 4 pcs

Part no 3A, 4 pcs

04-09-2014-QJ

Step #1 --SECURING BASE FLANGES

Sit the building boxes in the chosen location. Remove all the

components from packaging to ensure all components are present by

checking with the Part List.

Figure 3 Position of Base Flanges

Begin by determining exact location of the four (4) corners of the building. Mark front

edge and side-to-side width of assembly on ground. Drive alignment stakes into the

ground outside of the markings, and draw alignment strings along both ends and sides

of the building to the dimensions shown in Figure 3. The outline of the strings will

represent the final location of the base flanges. The initial location of each Corner

Base Flanges (5R & 5L) is critical to the alignment and fit of the frame components

and cover.

Locate the Left Corner Base Flange and Right Corner Base Flange(5R&5L). Secure

the base flanges with Stake Pegs (Part #17). Measurements shown in Figure 2 are to

the center of the upright sockets on each Base Flange.

The Shelter must be secured to a firm surface that can receive and retain augers and

pegs firmly in position. The shelter should be installed on FIRM GROUND, not on

SWAMP, SOFT/WET GROUND. The Base Flanges must be secured so they cannot

be moved. Arches are tensioned at their base as they insert into the Base Plate sockets.

Step #2 --ARCH ASSEMBLY

Assemble each arch on ground. Each arches consist of:

One curving roof tube (Part #1)

Two roof curving tube (Part #2/2A)

Two curving sidewall tube (Part # 3/3A)

Figure 4 the arch installation

Connect the arches by Using the hexagon bolts with washers and nuts through

predrilled holes in frame members. Do not tighten down the nuts completely until

frame is fully assembled and set in place.

THE FRONT PANEL FRAME ASSEMBLY

Figure 5 Frame Installation for Front Panel

Assemble the front panel frame. According to Figure 5, connect the end wall frame by

Using the bolts with washers and nuts through predrilled holes in frame members. Do

not tighten down the nuts completely until frame is fully assembled and set in place.

NOTE: Please notice that the part code of the arch sections.

The sections of different arches are not the same.

Check with the Part List and the Sketch Figure #1.

Step #3 --ERECTING ARCHES

Figure 6Attaching Arches to Base Flanges

Begin frame assembly by erecting Front Arch into Front Corner Base Flanges. Place left

frame sidewall tubing into the upright tube socket into the Left Base Flange. Place Hexagonal

Bolt through base flange socket and arch sidewall tube hole.

In order to insert Right Sidewall Tube into Right Front Corner flange, it is necessary to

support arch on left side to prevent movement. Position the Right Sidewall Tube over the

Right Corner Base Flange.

Once the Right Sidewall Tube is placed into right corner base flange, insert a hexagonal bolt

and nut to prevent it from popping out of the socket while

assembly continues.

Next stand first interior arch up to repeat insertion into Base flanges.

Figure 7

Immediately after putting first interior arch into place, connect Front Arch and Interior

arch using Roof Purlin Tubes at top ridge and side shoulder cures of arches. Secure

the Roof Purlin tubes into place using carriage bolts and nuts.

Nets install the Wind Brace supports(part#13) and Tube Clip(part#13A) that connect

the Front Arch to the first Interior Arch. The Wind Braces give the arch assemblies

strength as a unit. Use Bolt M10Χ30 at the end of each Wind Brace Support to

secure.

Continue to install other Arches Assemblies in the same manner. Overlap pinched

ends of Roof Purlin onto same carriage bolts inside frame assembly.

Next check entire frame assembly for square and plumb. Next tighten frame bolts

adequately. DO NOT over tighten bolts so as to oval or compress frame

components.。

Table of contents

Other Dancover Tent manuals

Dancover

Dancover 2m Series User manual

Dancover

Dancover TentZing CT168200 User manual

Dancover

Dancover Semi Pro XL 6m Series User manual

Dancover

Dancover PRO XL User manual

Dancover

Dancover Proshed Garage User manual

Dancover

Dancover B788 User manual

Dancover

Dancover Semi PRO 5x10m User manual

Dancover

Dancover Tentzing Explorer Series User manual

Dancover

Dancover 2m Series User manual

Dancover

Dancover 3m storage pro User manual

Dancover

Dancover PARTY TENT SEMI PRO CombiTent 8m Series User manual

Dancover

Dancover CombiTent SEMI PRO 6m Series User manual

Dancover

Dancover ProShed User manual

Dancover

Dancover Titanium User manual

Dancover

Dancover ST145080 User manual

Dancover

Dancover Pagoda User manual

Dancover

Dancover Oceancover PVC User manual

Dancover

Dancover TentZing CT168300 User manual

Dancover

Dancover Pagoda Marquee UNICO 6x6m User manual

Dancover

Dancover Pole Tent Semi PRO 6x6m User manual

Dancover

Dancover 5.4m Series User manual

Dancover

Dancover Pagoda Marquee UNICO 7x7m User manual

Dancover

Dancover Semi PRO 4x8m User manual

Dancover

Dancover Patio Cover Expert 3x5m User manual

Popular Tent manuals by other brands

OZTENT

OZTENT JV SIGNATURE EDITION owner's manual

GigaTent

GigaTent Summer Chalet Mini Tent owner's manual

Coleman

Coleman 2000007827 Setup instructions

ShelterLogic

ShelterLogic 107153 Assembly instructions

Outsunny

Outsunny 84C-230 manual

Napier

Napier SPORTZ COVE 61 Series instructions

EuroTrail

EuroTrail ATLANTIS PRO manual

Reimo

Reimo Marina instructions

TiiTENT

TiiTENT TB300 manual

Coleman

Coleman 2000033134 Assembly & instruction manual

Ozark Trail

Ozark Trail W784.1 Assembly instructions and owner's manual

SlingFin

SlingFin CrossBow 2 instructions

Coleman

Coleman 9600-141 instructions

Palram

Palram Arizona 5000 Wave - WINGS manual

COVERPRO

COVERPRO 56184 Owner's manual & safety instructions

Vango

Vango Zenith 100 instructions

Costway

Costway PATIOJOY OP70818 user manual

Clarke

Clarke PUC 88 Assembly guide