Daikin ARC412A6 User manual

ARC412 Series Si10-416A

60 Remote Controllers

ARC412A6

ON TIMER

TEMP

CANCEL

MODE FAN

HR.HR.

SWING

ON / OFF

OFF TIMER

OFF TIMER ON TIMER

POWERFUL

Si10-416A ARC412 Series

Remote Controllers 61

1. SIGNAL TRANSMITTER

Send signals to the air conditioner.

2. ON/OFF button

Press once to start operation.

Press once more to stop operation.

3. ROOM TEMPERATURE

ADJUSTING buttons

Use these buttons to set the room temperature as you

like.

Temperature setting range

COOL ... 18°C - 32°C

HEAT ... 14°C - 28°C

AUTO ... 18°C - 28°C

4. TIMER OFF SETTING button

5. TIMER ON SETTING button

6. TIMER CANCEL button

7. AIR FLOW ADJUSTING button

Five choices are available for airflow setting. "AUTO",

the computer changes the air flow automatically

according to the room temperature.

8. OPERATION MODE SELECTOR button

9. SWING button

10. POWERFUL mode button

Note:

Display monitor function :

You can check or change settings when the air

conditioner is stopped. To check, press once the button

for the setting you are checking. To change the setting,

press the same button again while the display is ON.

Unit operation panel and display panel

OPERATION indicator lamp

(green)

Lights up on system activation

irrespective of operation mode.

TIMER indicator lamp

(green)

Lights up when “TIMER ON” or “TIMER

OFF” countdown is in progress.

Temperature sensor

monitors room temperature.

ON/OFF button

Signal receiver

Receives signals from the remote controller.

Si10-416A ARC412 Series

Operation 183

1. ARC412 Series

1.1 Preparation Before Operation

Setting dry batteries

Remote controller

Address switch

(Address switch is

normally set to 1)

ARC412 Series Si10-416A

184 Operation

Setting dry batteries

1. Slide the back cover of the remote controller in the direction of

the arrow and take it off.

2. Set two dry batter

ies in accordance with the indications of (+) and (–).

Note on batteries

1Use two LR03 (AAA) batteries.

1Never mix new and old batteries or different type of batteries.

1Never try to charge the batteries.

Used-up batteries must be taken out all at once and disposed-off properly.

1In case the remote controller will not be used for a long time take

out all batteries in order to prevent liquid leak from the batteries.

1Batteries life is about a year under normal use conditions.

Replace the batteries with new ones when, on pressing a button,

the display shows all figures at the same time and the remote

controller does not send signals to the air conditioner.

Address switch

1Address switch is used for the installation of 2 units in one room.

Contact the shop you purchased this DAIKIN room air conditioner

if you would like to have 2 units/room.

1Signals cannot be received if the address switch selects a signal

different from that of the main unit.

Si10-416A ARC412 Series

Operation 185

1When using, aim the signal transmitter at

the air conditioner.

The operative distance between the

remote controller and the air conditioner

is about 7 m on a straight line.

A “peep” sound is heard when the unit

receives a signal from the remote controller.

1If there is an obstruction between the

signal transmitter and the receiver, such

as curtains or doors, the air conditioner

will not operate.

1Signal may not be received in a room with

an electronic ballast type fluorescent

lamp. Please consult with your dealer

before buying a new fluorescent lamp.

1If another electric appliance is operated by

the remote controller, move the appliance

away, or consult with your dealer.

Use

ARC412 Series Si10-416A

186 Operation

Caution

1Never throw the remote controller nor strongly shock it.

Do not get it wet, either.

1Take care not to let children play with the buttons.

If installed on a wall, etc.

1To prevent loss or damages of the remote

controller, fix it on a wall or pillar using a

remote controller holder. First, check that

the signals from the remote controller in

the place you chose can reach the air

conditioner, and then fix it in the place.

1Avoid fixing the remote controlelr at such

corner as marked by in the

figure, near a heater, or in a place

exposed to sun light.

Si10-416A ARC412 Series

Operation 187

1.2 PROGRAM DRY Operation

The microcomputer function of the air conditioner takes away the

moisture with the minimum temperature decrease.

ON TIMER

TEMP

CANCEL

MODE FAN

SWING

ON / OFF

OFF TIMER

OFF TIMER ON TIMER

POWERFUL

ARC412 Series Si10-416A

188 Operation

1. Set the mode to “ ” (PROGRAM DRY).

2. Press ON/OFF button.

The OPERATION indicator lamp lights up.

To stop

Press ON/OFF button.

The OPERATION indicator lamp goes out.

The microcomputer functions determining the

appropriate room temperature and humidity, and the

operating cycles of the external compressor and

interior fan, which allow maintaining these levels

based on the ambient temperature and humidity at the

time of switching on this function.

Note:

The PROGRAM DRY function is designed primarily

for dehumidification and not for lowering room

temperature – but remember a dehumidified room will

always “feel” cooler than a humid one.

PROGRAM DRY operation is not possible in ambient

below 18°C.

There is no need to set the THERMOSTAT SETTING

selector or FAN SPEED selector as PROGRAM DRY

operates independently of them.

Si10-416A ARC412 Series

Operation 189

1.3 Adjusting the Air Flow Direction

Adjusting vertical direction:

Make sure to use the SWING button to adjust it.

1. SWING

Press the SWING button. The flap automatically

swings according to the operation mode.

2. SWING stop

Watching the flap movement, press the SWING

button at the position of your choice.

The recommended ranges for stopping the flap are

shown left.

Note:

Once you stop the flap at the position you like, the

position is saved in the memory.

Next time you use the air conditioner, the flap will stop at

that position.

ON TIMER

TEMP

CANCEL

MODE FAN

SWING

POWERFUL

1, 2

ARC412 Series Si10-416A

190 Operation

Caution

1Before adjusting the horizontal

direction, stop the swing flap at a

position convenient for the adjustment,

referring to “Adjusting Vertical

Direction”.

1In COOL or PROGRAM DRY mode, if

the flap is stopped at an upward

position, the flap automatically moves

during 15 minutes to prevent

condensation on it.

1At the start of HEAT mode, human bodies

feel uncomfortable if directly exposed to the

air flow even if it is warm.

So DAIKIN has adopted the THREE-STEP

Flow system, to provide a comfortable warm

air around you.

Table of contents

Popular Remote Control manuals by other brands

Panasonic

Panasonic EUR7622KB0 Operation guide

Bang & Olufsen

Bang & Olufsen Beo4 user manual

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 user manual

Multiplex

Multiplex PROFI TX 9 instructions

One Remote

One Remote RMB4 user manual

FUTABA

FUTABA 9ZAP - PART2 manual

HR Matic

HR Matic HR MULTI 3 quick start guide

Yamaha

Yamaha ACC-GNRST-30-20 installation instructions

EisSound

EisSound KBSOUND user manual

Marantz

Marantz RC101 user guide

Conrad

Conrad FS20 TC6 operating instructions

Anritsu

Anritsu MP1777A Operation manual

Niles

Niles WVC100 Installation & operating guide

RCA

RCA RCU1300 manual

Bang & Olufsen

Bang & Olufsen BEO6 Getting started

GE 94901 instruction manual

Onbon

Onbon YQ1-75 user manual

FUTABA

FUTABA R7108SB Full manual