CYP PUV-44XPL-4K22-KIT User manual
PUV-44XPL-4K22-KIT
4 x 4 HDMI HDBaseT™ LITE Matrix with 2x Independent
HDMI outputs & Audio De-embedding (4K, HDCP2.2,
PoH, 60m) inc. 4x PUV-1210PL-RX Receivers
OPERATION MANUAL
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 05/08/16 First release
CONTENTS
1. Introduction................................................................................... 1
2. Applications.................................................................................. 1
3. Package Contents ....................................................................... 2
4. System Requirements................................................................... 2
5. Features......................................................................................... 3
6. Operation Controls and Functions.............................................. 4
6.1 Front Panel ............................................................................... 4
6.2 Rear Panel ............................................................................. 5
6.4 Remote Control....................................................................... 7
6.5 OLED Menu .............................................................................. 8
6.6 IR Cable Pin Assignment......................................................... 9
6.7 RS-232 Protocol........................................................................ 9
6.8 RS-232 and Telnet Commands ............................................ 10
6.9 Telnet Control ........................................................................ 14
6.10 WebGUI Control .................................................................. 16
6.10.1 Video Switch..................................................................... 18
6.10.2 Zone A/V Pairing .............................................................. 23
6.10.3 EDID Settings ..................................................................... 24
6.10.4 HDBaseT & H/W Info......................................................... 26
6.10.11 User Cong...................................................................... 27
6.10.12 System Settings ............................................................... 27
6.10.13 EDID Setting ................................................................... 28
6.10.13 Logout ............................................................................. 28
7. CONNECTION DIAGRAM............................................................ 29
8. SPECIFICATIONS.......................................................................... 30
8.1 Technical Specications....................................................... 30
8.2 Supported Timing Table & Maximum HDMI Cable Length .... 31
8.3 Supported Audio Formats .................................................... 32
8.4 HDBaseT Features.................................................................. 33
8.5 CAT5e/6/7 Cable Specications......................................... 34
9. ACRONYM................................................................................... 35
1
1. INTRODUCTION
The PUV-44XPL-4K22 HDMI/HDBaseT Matrix supports the
transmission of video (resolutions up to 4K2K@60Hz, HDCP 2.2,
HDMI2.0) and multi- channel digital audio from 4 HDMI sources
to 4 HDBaseT outputs and 2 independent HDMI2.0 outputs.
HDBaseT outputs allow transmission via a single CAT5e/6/7
cable up to 70m, whilst the independent HDMI outputs support
cable lengths of up to 10m.
The LPCM7.1 CH, Dolby TrueHD, Dolby Digital Plus, Dolby Atmos
and DTS-HD Master Audio transmission are supported. Further,
the L/R analogue audio for each HDBaseT zones (outputs A to
D) are able to be breakout.
The Power over HDBaseT (PoH) function provides power to
compatible receivers.
Control is via manual selection buttons, IR, RS-232, Telnet or
WebGUI. CYP provide control drivers for all the major control
systems. The PUV-44XPL-4K22 is designed to be used with PUV-
1210PL-RX receivers that can utilize the PoH capabilities of the
matrix.
2. APPLICATIONS
• Residential AV matrix installation
• Commercial AV matrix installation
• Security systems
• University lecture hall systems
• Retail installation systems
2
3. PACKAGE CONTENTS
• 1× 4x 6 Matrix system
• 1×24V DC Power Adaptor
• 4×IR Blaster
• 4×IR Extender
• 2×Racked Ear
• 1×Remote Control (CR-163)
• 1×UK Power Cord
• 1×Europe Power Cord
• 1×Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI equipped source devices
• HDMI equipped displays
• Compatible HDBaseT receivers – PUV-1210PL-RX
• Industry standard CAT6/7 cables
• HDMI cables – ‘Premium High Speed HDMI Cables’ are commended
with 6G HDMI sources.
3
5. FEATURES
• HDMI 2.0, HDCP1.4 and HDCP2.2 compliant
• Routes four HDMI sources to four displays using four HDBaseT outputs
and two independent or mirrored HDMI outputs
• Supported HDBaseT resolutions: VGA~WUXGA, 480i~1080p, 4K
UHD@24/25/30Hz (R:G:B 4:4: & Y:U:V 4:4:4 & Y:U:V 4:2:2), 4K UHD@
60Hz (YUV 4:2:0), dependent upon the output display’s EDID settings
• Supports resolutions up to 4K@60 (YUV 4:4:4) on HDMI output ports
• Supports automatic 4K@60 YUV 4:4:4 to YUV 4:2:0 conversion for
HDBaseT outputs
• 4K/2K & 4K UHD signals can be transmitted up to 35m via CAT5e/6
and 70m via CAT6a/7
• The LPCM7.1 CH, Dolby TrueHD, Dolby Digital Plus, Dolby Atmos and
DTS-HD Master Audio transmission are supported.
• Further, the L/R analogue audio for each HDBaseT zones (outputs A
to D) are able to be breakout.
• Advanced internal and external EDID management with 4 sets of
congurable EDID settings
• Bi-directional IR support over HDBaseT
• The Power over HDBaseT (PoH) function provides power to
compatible receivers.
• Control is via RS-232, remote control, on-panel control and IP
Control (Telnet & WebGUI)
• 1U rack mounted design
4
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER
LOCK
A1B2C3D4E5
F698710ENTER
PRESET
MENU
/CANCEL +
IN
-
OUT
21 3 6 8 10
5 7 9
114
1POWER: Press this button to power on/ off device.
2POWER LED: The LED will illuminate in green when the power is on,
and shown in red when power off this device.
The network function will remain active once press this power off
button. This is for connected Receiver can get power when matrix
unit be power off.
3IR WINDOW: Receiving remote control signal to control this device,
please use the remote control unit supplied in the package.
4OUTPUT A~F & INPUT 1~4: Press “OUT” button to select the output
source (A~F). Next, press output keys (A~F) to select output source;
then press “IN” key to select input source (1~4). Finally, press “ENTER”
to conrm selection.
For example, if outputs A~D need to be assign to input 1, following
sequences of button presses need to be performed: OUT → A,B,C,D
→ IN → number key “1” →ENTER
If all output source would like to be assigned to single input, press
“OUT” button and all input buttons “A~F” then press “IN” and enter
the number key of input and enter to conrm the selection.
5MENU & CANCEL: Press “MENU” button to access the LCM menu.
The menu tree please refers to section 17. Press “CANCEL” button
to cancel the selection.
6ENTER: Press this button to conrm the selection.
7PLUS (+)/IN: Press Plus “+” button to navigate up button selection.
Press “IN” button for input port sources selection.
5
8MINUS (-)/OUT: Press Minus “-” button to navigate down button
selection. Press “OUT” button for output port sources selection.
9LOCK: Press this button for three second to lock all buttons on
panel. The right top side will display “L” once front panel locked.
Press for few seconds to unlock.
10 PRESET: Press this button to recall preset setting, allow maximum
8 sets preset setting to recall. The preset settings are able to be
completed on WebGUI. Please refer to section 9.1.4 for advanced
preset setting.
11 LCM: The LCM displays the setting and information.
6.2 Rear Panel
95 7
63
8421
1HDMI IN & IR Out 1 ~ 4: Connect to source devices with HDMI
interface and HDMI cable, the input source devices includes DVD
players, Set-top Boxes and so on. The qualied HDMI cables are
recommended. The DVI source is complaint; please use cable to
converts DVI to HDMI. The IR In provides customer to transmit the
IR signal to connected displays. Please use the remote control unit
supplied in the package.
2CAT5e/6 OUT & IR IN A~D: Connect from these Cat5e/6 outputs to
input port of compatible Receivers with a single CAT5e/6/7 cable
for HDMI Audio/Video and IR/RS-232 control signal transmission.
The IR Out provides customer to transmit the IR signal to matrix unit
from display installation sites. Please use the remote control unit
supplied in the package.
3ZONE AUDIO OUT: Four sets of audio output from HDBaseT output.
The ampliers are able to be connected for audio source
broadcasting.
6
4IR IN (ALL): Connect an IR extender for IR signal reception. Ensure
that remote being used is within the direct line-of-sight of the
IR extender. IR signals received will transmitted by all IR blasters
connected to the matrix or Receivers.
5IR OUT (ALL): Connect an IR Blaster for IR signal transmission to
the source/input location. Place the IR Blaster in direct line-
of-sight of the equipment to be controlled. It will transmit all IR
signals Received by any IR extenders connected to the matrix or
Receivers.
6RS232: Connect to a PC or control system with D-Sub 9-pin cable
to control the matrix with RS-232 commands (refer to Sections 7)
7CONTROL: Connects matrix unit with PC or laptop via RJ-45 cable
for Telnet or WebGUI control(the details of Telnet and WebGUI,
please refers to Sections 9 and 10).
8SERVICE: Please plug in USB thumb drive to update Firmware in
eld. The USB thumb drive shall plug in and select update “YES” on
front panel and rmware in USB thumb drive to complete rmware
update.
9MAIN 24V: Plug the 24 V main power supply in the package for
power on the matrix unit. If connect with POH Receiver, please
plug 24V power supply to POH outlet for supplying power over
cable to compatible Receiver with POH function.
6.3 Side Panel
1
1FAN VENTILATOR: These are air ventilation areas, DO NOT block
these areas or cover it with any object. Please allow adequate
space around the unit for air circulation.
Table of contents
Other CYP Matrix Switcher manuals
CYP
CYP PU-8H8HBTPL User manual
CYP
CYP CMSI-8H8CVE User manual
CYP
CYP PU-424HBTE User manual
CYP
CYP CPLUS-44PLV User manual
CYP
CYP CMPRO-U8H8CVE User manual
CYP
CYP CMLUX-44E User manual
CYP
CYP OR-HD44E User manual
CYP
CYP CPLUS-V4H2HP-DT User manual
CYP
CYP PU-424HBTL-KIT User manual
CYP
CYP PU-8H8HBTE User manual
CYP
CYP CMSI-1616 User manual
CYP
CYP CDPS-4H4HFS User manual
CYP
CYP OR-YUV44S User manual
CYP
CYP PU-8H8HBTPL-4K22 User manual
CYP
CYP CMPRO-U4H4CVE User manual
CYP
CYP CDPS-44SM User manual
CYP
CYP CPLUS-V32USBC User manual
CYP
CYP CDPS-U10H2HFS User manual
CYP
CYP OR-42SA-4K22 User manual
CYP
CYP Elpro Video Labs CDPS-UC4H4HFS User manual
