CyberPower RMCARD202 User manual

User’s Manual

Network Management Card

RMCARD202

Intelligent Network Management Card

allows a UPS system to be managed,

monitored, and configured

Version 1.0

E-K01-SNMP005-0

CyberPower Network Management System

TABLE OF CONTENTS

Introduction………………………………………………………………………1

Installation Guide………………………………………………………………..3

Web Interface…………………………………………………………………... 8

Reset to Default Setting / Recover from a Lost Password…………………15

Firmware Upgrade…………………………………………………….………..16

Trouble Shooting…………………………………………………….………….17

Appendix……………………………………………………………..…………..18

INTRODUCTION

Overview

The CyberPower Network Management Card allows for remote monitoring and control of a UPS

attached to a network. After installing the hardware and configuring an IP address, the user can

access, monitor, and control the UPS from anywhere in the world! Simply use a web browser

such as Internet Explorer or Firefox to access your UPS. Servers and workstations can be

protected by the UPS utilizing the PowerPanel Business Edition Client version to gracefully

shutdown when signaled by the Network Management Card.

Features



Real time UPS monitoring



Remote management and configuration of UPS via Web Browser or NMS



Auto-shutdown to protect servers/workstations from data lose due to power failure



Schedule shutdown/start-up/reboot of the UPS via remote control



Event logging to trace UPS operational history



Data logging for analyzing power conditions



Event notification via email and SNMP traps



Support TCP/IP ,UDP,SNMP/HTTP,NTP,DNS,SMTP protocol



SNMP MIB provided



Quick installation and user friendly interface



User upgradeable firmware via FTP



Security management provided

System Requirements

A computer with a Windows or Linux Operating System (for optional PowerPanel

Business Edition Client)

An Ethernet connection to an existing network

NMS (Network Management Station) compliant with SNMP (for optional NMS

management)

CyberPower Network Management System

Application:

Unpacking

Inspect the Network Management Card upon receipt. The package should contain the following:

CyberPower Network Management Card.

PowerPanel Business Edition CD with software and user manuals.

CyberPower Network Management System

INSTALLATION GUIDE

Step 1. Hardware Installation

Internal smart slot network management card (RMCARD202)

1. Turn off the UPS before removing the expansion port cover on the UPS.

2. Remove the two retaining screws from the expansion port cover and remove the cover.

3. Install the CyberPower Network Management Card into the expansion port.

4. Re-install and tighten the retaining screws.

5. Connect the Ethernet cable to the LAN port on the CyberPower Network Management

Card.

6. Turn on the UPS.

CyberPower Network Management System

Definitions for LED Indicators

Link LED color Condition

Off The Network Management Card is not connected to the Network/

or the Network Management Card Power is off

On(Yellow) The Network Management Card is connected to the Network

TX/RX LED color

Off The Network Management Card power is off

On(Green) The Network Management Card power is on

Flash - Receiving/transmitting data packet

- Reset finished

Step 2. Configure the IP address for the CyberPower Network Management Card.

Method 1 : Using the CyberPower Power Device Network Utility Tool

1. Install the CyberPower Power Device Network Utility Tool from the included CD. It is located

on the CD in the \tools\network folder. Double click the “Power Device Network Utility”

installation file, “Setup.msi” to begin the installation.

2. After installation is complete, run the “Power Device Network Utility” program. Under “All

Programs, Select ”CyberPower Power Device Network Utility”.

3. The main dialog of the “Power Device Network Utility Tool” program is shown in Figure. 1. The

configuration tool will display all CyberPower network cards of present on the same network.

The "Refresh" button is used to search the entire local network for SNMP cards.

○

○○

○

1 Ethernet connector

○

○○

○

2 LINK Indicator

○

○○

○

3 RX/TX Indicator

CyberPower Network Management System

Figure 1. The main window of the “

Power Device Network Utility

” program.

4. Select the SNMP card you are setting up. Click on the Tools menu and select “Device Setup”

or double click the SNMP card you want to configure.

5. You can modify the IP Address, Subnet Mask, and Gateway address for the Device MAC

Address listed in the Device Network Settings window, as shown in Figure 2.

Figure 2. The SNMP card setting window.

6. To modify the IP Address, Subnet Mask or Gateway address, enter the new addresses into the

corresponding fields.

7. You will need to enter a User Name and Password for the SNMP card (Figure 3) in the

authentication window, as shown in figure 3. *Default user name: cyber; Default password:

cyber

Figure 3. Authentication window.

CyberPower Network Management System

8. If IP address is successfully set, you will see a message that the IP set up is OK, as shown in

Figure 4.

Figure 4. Setup IP Address successfully message.

CyberPower Network Management System

Method 2: Using a command prompt

1.Obtain the MAC address from the label on the Network Management Card rear panel. Each

Management card has a unique MAC address.

2.Use the ARP command to set the IP address.

Example:

To assign the IP Address 192.168.20.240 for the Network Management Card,

which has a MAC address of 00-0C-15-00-00-01 you will type in the following

command prompt from a PC connected to the same network as the Network

Management Card.

1. Type in “arp-s 192.168.20.240 00-0C-15-00-00-01” then press Enter.

3.Use the Ping command to assign a size of 123 bytes to the IP.

1. Type in “ping 192.168.20.240 -1 123” then press Enter

2. If the replies are received, your computer can communicate with the IP address.

To select an IP address for the Network Management Card, please refer to Appendix 1.

CyberPower Network Management System

WEB INTERFACE

There are two user account types.

- Administrator (default username : cyber ; default password : cyber)

- Viewer (default username : device ; default password : cyber)

The Administrator can access and control all functions, including enable/disable of the

Viewer account. The Viewer’s access allows them read permissions for all functions but

they cannot control or change any settings.

Note: The Administrator account is also used for the FTP log in and authentication

check in the Power Device Network Utility

Web Content

[Summary] provides an overview of the system operation and the items that are auto refreshed.

Item Definition

Current condition Display the current operating condition of UPS

Battery Capacity The percentage of the current UPS battery capacity in a

graph.

Load The load of UPS as a percentage of available Watts in a

graph.

Remaining runtime How long the UPS can support its load by battery power.

Name The name of UPS used for identification.

Location The location of the UPS.

Contact The person accountable for the maintenance of the

UPS.

Uptime How long the system has been working continuously.

Recent Device Events A list of events that recently occurred.

Other manuals for RMCARD202

Table of contents

Other CyberPower Network Card manuals

CyberPower

CyberPower CyberPower RMCARD201 User manual

CyberPower

CyberPower RWCCARD100 User manual

CyberPower

CyberPower Network Management Card User manual

CyberPower

CyberPower Network Management Card User manual

CyberPower

CyberPower PowerPanel Business Edition User manual

CyberPower

CyberPower RMCARD205 User manual

Popular Network Card manuals by other brands

FirstComm

FirstComm OBiWiFi5G Setup guide

Sun Microsystems

Sun Microsystems Interface Adapter user guide

TRENDnet

TRENDnet TU2-ETG user guide

YASKAWA

YASKAWA SI-EN3 Technical manual

Paradyne

Paradyne BitStorm 2600 IP DSLAM installation guide

Belkin

Belkin F5D7050 user manual

3Com

3Com EtherLink 3C509B quick guide

TRENDnet

TRENDnet TEG-PCITX user guide

Cisco

Cisco MC16E installation guide

Delta Electronics

Delta Electronics Braking Modules VFDB Series instruction sheet

TwinMOS

TwinMOS Booming user manual

Dialogic

Dialogic Media Board DM/V1200BTEPEQ installation guide

Buffalo

Buffalo AirStation WLI-PCM-L11GP user manual

National Instruments

National Instruments NI 9234 operating instructions

Hama

Hama 49276 Operating instruction

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Product data

Compaq

Compaq Wireless LAN 100 specification

Bose

Bose PowerMatch Dante quick start guide