CTC Union SB262 Series User manual
SB262 Series Switch BoxSB262 Series Switch Box
12 Sensor Inputs12 Sensor Inputs
Product ManualProduct Manual
2
• Introduction...................................................................3
• Product Description...........................................................3
• Product Dimensions and Diagram .............................................4
• Mounting Instructions .........................................................5
• Conduit Entry .................................................................6
• Grounding ....................................................................7
• Installation of Sensor/Signal Input Cable.......................................8
• Post-Installation Testing..................................................... 11
• Warranty and Return Information ............................................ 13
T C
3
I
CTC junction box solutions allow for the monitoring of remotely-mounted
vibration sensors, which would be otherwise restricted to human access due to
safety considerations.
SB262 Series Switch Box Overview: Four to 12 sensor inputs (four to 12
measurement channel outputs), stainless steel slope top enclosure
The SB262 Series Switch Box is a common cable termination point for bringing
sensor cables into a switch box for routine data collection with portable data
collectors.
The SB262 Switch Box is used to convert the two-conductor input wiring of up to
12 remotely-installed sensors, proximity probes and/or temperature probes to a
switched BNC and a switched two-pin MIL spec connector for data collection.
Input wiring from each sensor is connected to the outputs via quick-connect or
screw terminal blocks. Each terminal block includes input for positive, common
and shield. Additionally, the SB262 Switch Box can be equipped with a multi-pin
connector for interface with online systems for continuous live readings. This
connection requires a JB905-1A or -2A plug.
The panel board located within the enclosure has a centrally-located switch that
determines that panel’s sensor output to the BNC and two-pin MIL connectors.
Measurement location cards are located on the inside of the enclosure door to
identify each channel.
Rated for NEMA 4X (IP66), the SB262 can withstand harsh environments
including temperatures ranging from -58°F to 180°F (-50°C to 82°C). The box is
also resistant to hose-directed fluid and corrosion. A twist lock is installed on
the door allowing the box to be sealed from the elements when not in use.
Note: The SB262 stainless steel switch box is internally grounded.
4
P D
Measurement
Location Card
Two-pin MIL
Output Connector
Switch
Optional Online
Expansion Jack
BNC
Output
Connector
Figure 1. Dimensions
Figure 2. Diagram
Front View Side View
Terminal Strip
Inputs
5
M I
SB262 Series Switch Boxes are supplied with integral mounting brackets
attached.
Note: If you have purchased a switch box without cable entries provided, you
should add your own entry prior to mounting the switch box.
Mounting
Holes
0.31 in./7.95 mm
Figure 3. Mounting Bracket Placement
6
C E
If you are running conduit to your enclosure, ensure the conduit cable entry is
located at the bottom of the enclosure when mounted.
Note: To ensure moisture will not flow into the enclosure, a hole should be drilled
at the lowest point in the conduit to provide drainage for any moisture.
Correct
Figure 4. Conduit Entry for Switch Box
Drill Drain
Hole Here
7
G
Ensure the shield ground wire on the SB262 Series Switch Boxes is grounded to
earth ground.
A. Mounting to Earth Ground
When mounting SB262 Series Switch Boxes to earth ground (such as an I-Beam),
no additional steps are necessary, as the enclosure is grounded internally.
Figure 5. Switch Box (SB262) Earth Ground
8
B. Mounting to Non-Grounded Structure
When mounting the switch box to a non-grounded structure, ensure the shield
ground wire or customer-supplied ground wire is tied to a source of earth ground.
S I
Installation of Sensors/Signal Input Cable
1. Feed blunt-cut end through the cable entry at the bottom of the switch box.
Note: It is recommended that cables are marked on both ends.
For cord grip cable entry, take off the cord grip cover with bushing and run cable
into enclosure, hand-tighten cord grip cover to base to prevent damage of cord
grip.
Figure 6. Ground Wire Placement
9
1. Strip outer jacket of cable back 1¼ in. and remove all of the shielding.
2. Separate the internal wires from the shield and twist the shield.
3. Strip red and black insulation back ¼ in.
Figure 8. Bottom View
Figure 7. Front View
Figure 9. Stripped Wire
(-)
Shield / Drain Wire
(+)
4. Locate the appropriate plug, identified by channel number, remove the plug and
install the wires using a small flathead screwdriver. Push Plug back into location.
Orientation is as follows:
a. Red insulated conductor wire is connected to (+).
b. Black insulated conductor wire is connected to (-).
c. Shield drain wire is connected to ground (GND).
d. Depress selected position button to open terminal for respective wire (may
require a mini athead screwdriver).
10
5. Insert plug into the appropriate PC board connector and double check to ensure
that the cable is going to the correct channel.
6. Mark the Measurement Location Card located on the inside front cover with a
description of each measurement location.
Figure 10. Field Wiring for Two-Conductor Sensor Inputs
CH1CH2CH3CH4CH5CH6
CH7CH8CH9CH10CH11CH12
+
-
GND
+
-
GND
+
-
GND
+
-
GND
+
-
GND
+
-
GND
+
-
GND
+
-
GND
+
-
GND
+
-
GND
+
-
GND
+
-
GND
1+
1-
2+
2-
3+
3-
4+
4-
5+
5-
6+
6-
7+
7-
8+
8-
9+
9-
10+
10-
11+
11-
12+
12-
Optional
Remote
Output
Optional
Remote
Output
SENSOR #1
SENSOR #2
SENSOR #3
SENSOR #4
SENSOR #5SENSOR #6
SENSOR #7
SENSOR #8
SENSOR #9
SENSOR #10
SENSOR #11
SENSOR #12
Sensor Inputs
Red = Positive
Black = Common
Grey = Shield (Ground)
Inputs Inputs
Table of contents
Other CTC Union Switch manuals
CTC Union
CTC Union IFS-402GSM-4PH24 User manual
CTC Union
CTC Union JB330 Series User manual
CTC Union
CTC Union GSW-3208M1 User manual
CTC Union
CTC Union ITP-500 User manual
CTC Union
CTC Union TSB6000 Series User manual
CTC Union
CTC Union FSW3224 User manual
CTC Union
CTC Union ITP-G800SM-8PH24 User manual
CTC Union
CTC Union FS-802GS-8PH User manual
CTC Union
CTC Union FRM220A-1000EAS/X User manual
CTC Union
CTC Union IFS?500 User manual
CTC Union
CTC Union ITP-1204GTM-12PHE User manual
CTC Union
CTC Union JB230 Series User manual
CTC Union
CTC Union VRM01/24 User manual
CTC Union
CTC Union IFS-803GSM-8PH24 User manual
CTC Union
CTC Union IGS-803SM User manual
CTC Union
CTC Union IGS-803SM-8PH24 User manual
CTC Union
CTC Union IGS-812SM Series User manual
CTC Union
CTC Union IGS+803SM-8PH User manual
CTC Union
CTC Union TSB1000 Series User manual
CTC Union
CTC Union JB120 Series User manual
