CSiSC PSiSC HD-58124 User manual
HD-58124
Toilet Partition Installation
Manual
PHONE: 803-252-3020
FAX: 803-256-7769
www.psisc.com
803-252-3020
2
ATTENTION
DO NOT MIX
FASTENER PACKS
EACH FASTENER PACK HAS THE NECESSARY
BOLTS, BARRELS AND SCREWS TO INSTALL
THE RESPECTIVE PANEL, PILASTER OR DOOR.
TORX HEAD BITS ARE PACKED IN THE EXTRA
FASTENER PACKS.
www.psisc.com
803-252-3020
3
TABLE OF CONTENTS
STEP PAGE
1 TOOLS REQUIRED................................... 4
2 GETTING STARTED ................................. 5
3 MARK THE PARTITION LAYOUT............. 6
4INSTALL THE PANELS............................. 8
5INSTALL THE WALL PILASTER
5A USING ‘Z’ BAR ANCHORING SYSTEM .......... 10
5B USING STANDARD LEVELING DEVICE......... 12
6INSTALL THE PILASTERS ..................... 14
7 INSTALL THE HEADRAIL ....................... 17
8 ATTACH THE DOORS ............................ 18
9 ATTACH THE DOOR HARDWARE ........ 20
10 ADJUSTABLE ALUMINUM PILASTERS. 22
11 BOLT AND BARREL SIZES .................... 23
www.psisc.com
803-252-3020
4
1 TOOLS REQUIRED
xTAPE MEASURE
x4 FOOT LEVEL
xRATCHET TYPE BIT DRIVER (torx head bits supplied)
xFLAT HEAD SCREWDRIVER
xPHILLIPS HEAD SCREWDRIVER
x1 WAY SCREWDRIVER
xTWO 9/16" OPEN END WRENCHES
xHAMMER
xTWO 12" BLOCKS
xDRILL
xROTARY HAMMER DRILL
xHACKSAW
x5/16" CARBIDE TIPPED HAMMER DRILL BIT
x5/8" CARBIDE TIPPED HAMMER DRILL BIT
x1/4" HIGH SPEED STEEL DRILL BITS
xCHALK BOX
www.psisc.com
803-252-3020
5
2 GETTING STARTED
2.1 Find the packing list in the box marked “Packing List”
2.2 Check delivered materials and make sure no parts are
damaged or missing.
2.3 Check dimensions in each bathroom against the shop
drawings marked “For Field Use”. Make notes of
differences.
2.4 Clear bathrooms to provide workroom.
Thank you for choosing partitions from Partition Systems Inc. of South
Carolina. We appreciate your business. At Partition Systems, we strive to
provide the industry’s best partitions with comprehensive installation
guides.
If you need assistance, have questions or comments; contact our customer
service department at:
Customer Service
Partition Systems Inc. of South Carolina
PO Box 181, Columbia, SC 29202
(803) 252-3020, Fax: (803) 252-6030
Partition Systems International of South Carolina
825 Garland St.
Columbia, SC 29201
www.psisc.com
803-252-3020
6
3 MARK THE PARTITION LAYOUT
3.1 Establish and mark the center of the panels across the
back wall according to shop drawings. For end-panels and
alcove-panels mark the outer edge. (See fig.3.1)
3.2 Establish and mark the panel-brackets on the back wall
18” and 64” from the finished floor.
3.3 Establish and mark the wall-pilaster location on the side
wall according to shop drawings. (See fig.3.1)
3.4 Establish and mark the pilaster-brackets on the side wall
18” and 64” from the finished floor.
3.5 Establish and mark the outer edges of each pilaster from
the back and side walls according to shop drawings. (See
fig.3.1)
3.6 Mark and drill holes for the floor fasteners.
3.6.1 For leveling devices mark 5/8” in from the end of the
pilaster(s), centered from front to back. Drill a 2” deep hole
in the floor with a 5/8" bit.
3.6.2 For shoe/heel place the shoe on the floor centered between
the outer edges of the pilaster Using the shoe as a template,
mark the holes. Drill a 2” deep hole in the floor with a 5/16"
bit. (See fig.5-B.1)
3.7 Mark wall bracket mounting holes using the brackets as a
template. Center and level the brackets before marking
(See fig.3.1). For end-panels and alcove-panels use the
outer edge.
3.8 Drill 5/16" holes for wall brackets.
3.9 Insert plastic anchors (FA-400) into holes.
3.10 Secure wall and pilaster brackets with 2” stainless steel
screws (FA-808).(See fig.3.2)
www.psisc.com
803-252-3020
7
www.psisc.com
803-252-3020
8
4 INSTALL THE PANELS
4.1 Place a 12" high support in position to hold up the panels.
(see fig. 4.1)
4.2 Set the panel on the support and slide the panel into the
wall brackets until the bottom is ½” from the wall.
4.3 Drill the bottom bracket hole through the panel with a ¼”
drill bit and secure with a ½" bolt (FA-900) and a ½" barrel
(FA-950).
4.4 Level the top of panel.
4.5 Drill the top bracket hole with a ¼” drill bit and secure with
a ½" bolt (FA-900) and a ½" barrel (FA-950).
4.6 Repeat steps 4.1 through 4.5 for each panel.
www.psisc.com
803-252-3020
9
www.psisc.com
803-252-3020
10
5 INSTALL THE WALL PILASTER
5A USING ‘Z’ BAR ANCHORING SYSTEM
5A.1 Place a lead anchor into the floor holes from step 3.6.
5A.2 Screw a 3/8" x 3½” threaded rod into the lead anchor. Place a
3/8" flat washer and 3/8" nut onto the rod and tighten with a 9/16"
wrench to secure the lead anchor.
5A.3 Place a second 3/8" nut and 3/8” flat washer onto the threaded
rod. Move the nut half way down the rod. (See figure 5A.1)
5A.4 Place the wall-pilaster onto the threaded rod and slide it into the
wall mounted pilaster-brackets.
5A.5 Adjust the 3/8" nut to raise (lower) the pilaster until the bottom
hinge hole is 19½” off the finished floor. (See figure 5A.1)
5A.6 Place the pilaster shoe onto the pilaster and place the pilaster
onto the threaded rod. Place a third washer and nut onto the
threaded rod.
5A.7 Set the bottom gap between the wall and the pilaster according
to the shop drawings. Tighten the top nut to secure the pilaster.
5A.8 Level the pilaster. Drill the top pilaster bracket hole with a ¼”
drill bit. Secure with a ½” bolt (FA-900) and a 5/8" barrel (FA-951).
5A.9 Drill the bottom bracket hole. Secure with bolt and barrel.
5A.10 Drill through the shoe and pilaster. Secure with a ½” bolt (FA-
900) and a 5/8" barrel (FA-951).
Table of contents
