Crestron TPMC-3SM User manual
Crestron TPMC-3SM & TPMC-3SMD
Isys®2.8” Wall Mount & Designer
Touch Screens
Configuration Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
Crestron, the Crestron logo, Crestron Toolbox, Fusion RV and Isys are either trademarks or registered trademarks of Crestron Electronics,
Inc. in the United States and/or other countries. Other trademarks and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others.
©2011 Crestron Electronics, Inc.
Crestron TPMC-3SM & TPMC-3SMD Wall Mount & Designer Touch Screens
Contents
Isys®2.8” Wall Mount & Designer Touch Screens: TPMC-3SM & TPMC-3SMD 1
Access the Setup Screens........................................................................................................... 1
Configure the TPMC-3SM or TPMC-3SMD ............................................................................4
Ethernet Setup .............................................................................................................4
Standby Setup..............................................................................................................7
Display Settings...........................................................................................................8
System Messages Disabled/Enabled..........................................................................10
About.........................................................................................................................10
Diagnostics ................................................................................................................11
User Project Mode Off/On ........................................................................................13
Save & Exit ...............................................................................................................13
Configuration Guide – DOC. 7269A Contents •i
Crestron TPMC-3SM & TPMC-3SMD Wall Mount & Designer Touch Screens
Isys®2.8” Wall Mount & Designer
Touch Screens: TPMC-3SM &
TPMC-3SMD
Access the Setup Screens
The setup screens are the starting point for configuring the TPMC-3SM and
TPMC-3SMD.
NOTE: If no project has been loaded or if an invalid project has been loaded, the
TPMC-3SM and TPMC-3SMD default to the setup menu screen.
The setup screens allow basic configuration procedures prior to regular operation of
the TPMC-3SM and TPMC-3SMD.
When power is applied for the first time, the screen shown in the following
illustration appears.
Initial Screen
Configuration Guide – DOC. 7269A Isys®2.8” Touch Screens: TPMC-3SM & TPMC-3SMD •1
Wall Mount & Designer Touch Screens Crestron TPMC-3SM & TPMC-3SMD
NOTE: Most screens on the TPMC-3SM and TPMC-3SMD are identical. The few
instances where they differ will be noted in the text.
Touch the screen to display the “Panel Setup Options” screen, shown in the
illustration below.
TPMC-3SM “Panel Setup Options” Screen
TPMC-3SMD “Panel Setup Options” Screen
During regular operation of the touch screen, there are two ways to activate the setup
functions:
1. Place a button on the project main page and assign the reserved join number
(17242) that activates setup.
2. Press hard keys 1, 2, 3 and 4, under the touch screen display, in sequence
twice (i.e. press 1, 2, 3, 4, 1, 2, 3, 4) within a five second period.
2 •Isys®2.8” Touch Screens: TPMC-3SM & TPMC-3SMD Configuration Guide – DOC. 7269A
Crestron TPMC-3SM & TPMC-3SMD Wall Mount & Designer Touch Screens
1234
The “Panel Setup Options” screen is comprised of buttons for Ethernet Setup,
Standby Setup, Display Settings and Diagnostics. In addition, there are buttons
that enable/disable system messages, that provide information About the touch
screen and (on the TPMC-3SM only), that select whether User Project mode is on or
off. There is also a Save & Exit button. The functions of each are detailed in the next
section of this guide.
Configuration Guide – DOC. 7269A Isys®2.8” Touch Screens: TPMC-3SM & TPMC-3SMD •3
Wall Mount & Designer Touch Screens Crestron TPMC-3SM & TPMC-3SMD
Configure the TPMC-3SM or TPMC-3SMD
Ethernet Setup
On the “Panel Setup Options” screen, touch Ethernet Setup to display the “Ethernet
Setup” screen, shown in the following illustration.
“Ethernet Setup” Screen
The “Ethernet Setup” screen displays information about your Link Status, Control
Connection, Mac and IP addresses. There is a button to enable/disable Ethernet Auto
Discovery and buttons that provide access to Control System Settings and IP
Address Settings.
Touch Control System Settings to display the “Control Systems” screen, shown in
the following illustration.
“Control Systems” Screen
4 •Isys®2.8” Touch Screens: TPMC-3SM & TPMC-3SMD Configuration Guide – DOC. 7269A
Crestron TPMC-3SM & TPMC-3SMD Wall Mount & Designer Touch Screens
The “Control Systems” screen provides information about IP addresses, CIP ID,
Device ID and Port for up to four entries.
NOTE: The TPMC-3SM and TPMC-3SMD can communicate with up to 16 control
systems but only the first four entries will be visible on the screen. Other entries will
be visible with Crestron Toolbox™ software.
Touch Add Entry to display the “Edit Control System Settings” screen (shown in
the following illustration), where IP Address / Hostname, Port, CIP ID and Device
ID can be accessed.
“Edit Control System Settings” Screen
Touch the IP Address / Hostname, Port, CIP ID and Device ID fields to make each
entry. Each will open an on-screen keyboard appropriate for the field. For example,
touching the IP Address / Hostname field will open the keyboard shown in the
following illustration.
On-Screen Keyboard for IP Address / Hostname
Configuration Guide – DOC. 7269A Isys®2.8” Touch Screens: TPMC-3SM & TPMC-3SMD •5
Wall Mount & Designer Touch Screens Crestron TPMC-3SM & TPMC-3SMD
After making the entry, touch OK to add it or CANCEL to cancel it. After making
all the appropriate entries, when you are returned to the “Edit Control System
Settings” screen, touch Save to keep the new settings or Cancel to cancel them.
Touch Back on the “Control Systems” screen to return to the “Ethernet Setup”
screen.
On the TPMC-3SM and TPMC-3SMD, DHCP is enabled by default. To switch to a
static IP address, touch IP Address Settings on the “Ethernet Setup” screen, to
display the “Edit IP Settings” screen, shown in the following illustration.
“Edit IP Settings” Screen
Touch the Enabled/Disabled button to toggle between DHCP enabled and disabled.
Then touch the field for the Static IP Address, Static Subnet Mask or Static Default
Gateway you wish to enter. The on-screen keyboard will appear. After entering the
addresses, touch Save to add the entries or Cancel to cancel them.
On the “Edit IP Settings” screen, touch Edit DNS Servers >> to display the screen
for editing these addresses, which is shown in the illustration below.
“Edit IP Settings” Screen (DNS Servers)
6 •Isys®2.8” Touch Screens: TPMC-3SM & TPMC-3SMD Configuration Guide – DOC. 7269A
Other manuals for TPMC-3SM
1
This manual suits for next models
1
Table of contents
Other Crestron Touchscreen manuals
Crestron
Crestron V-Panel V15 User manual
Crestron
Crestron TPMC-9L How to use
Crestron
Crestron TSW-552 User manual
Crestron
Crestron TPMC-4SMD How to use
Crestron
Crestron TST-902 Owner's manual
Crestron
Crestron FlipTop FT-TS600 Owner's manual
Crestron
Crestron TPMC-V12 & TPMC-V15 User manual
Crestron
Crestron TPMC-8X-GA User manual
Crestron
Crestron TPMC-8X-GA User manual
Crestron
Crestron TPMC-8T-GA User manual
Crestron
Crestron TSW-752 Dimensional drawing
Crestron
Crestron TSW-750 User manual
Crestron
Crestron V-Pane TPMC-V12 User manual
Crestron
Crestron TSW-760 User manual
Crestron
Crestron TSS-752 User manual
Crestron
Crestron V12 User manual
Crestron
Crestron TPMC-8X-GA User manual
Crestron
Crestron TSW-730 Dimensional drawing
Crestron
Crestron TPMC-8X-GA User manual
Crestron
Crestron TSW-732 User manual
Popular Touchscreen manuals by other brands
Elecro Engineering
Elecro Engineering Poolsmart Plus Installation & operating manual
Johnson Controls
Johnson Controls IQ4 HUB installation manual
Elo TouchSystems
Elo TouchSystems ET2270L user manual
Elo TouchSystems
Elo TouchSystems ET1002L user manual
Elo TouchSystems
Elo TouchSystems 3201L user manual
Duratec
Duratec S15 user manual
