Crestron TMK-12L User manual

Crestron TMK-12L & WMKT-12L

Trim Ring Mount Kits

Installation Guide

This document was prepared and written by the Technical Documentation department at:

Crestron Electronics, Inc.

15 Volvo Drive

Rockleigh, NJ 07647

1-888-CRESTRON

All brand names, product names and trademarks are the property of their respective owners.

Crestron TMK-12L & WMKT-12L Trim Ring Mount Kits

Contents

Trim Ring Mount Kits: TMK-12L & WMKT-12L 1

Description.................................................................................................................................1

Setup ..........................................................................................................................................2

Supplied Hardware ......................................................................................................2

Installation...................................................................................................................4

Resources.................................................................................................................................10

Industry Compliance .................................................................................................10

Reference Documents................................................................................................10

Further Inquiries ........................................................................................................ 10

Future Updates .......................................................................................................... 10

Return and Warranty Policies ..................................................................................................11

Merchandise Returns / Repair Service ...................................................................... 11

CRESTRON Limited Warranty.................................................................................11

Installation Guide – DOC. 6360A Contents •i

Crestron TMK-12L & WMKT-12L Trim Ring Mount Kits

Trim Ring Mount Kits:

TMK-12L & WMKT-12L

Description

Trim Ring Mount Kits are the preferred method of mounting the Crestron Isys®

TPS-12L, TPS-12G-QM-L wall mount touchpanels, and the Isys i/O TPMC-12L

wall mount touchpanel media center when a finished appearance within a neatly

trimmed cutout is required. This application is perfect for wallpapering.

NOTE: If mounting into a material other than drywall (for example, wood lectern,

concrete, or rock) use the cutout template, available in the post-construction kit

WMKT-12L. For concrete and rock mounting material, allow for proper ventilation

before mounting the touchpanel.

There are two Trim Ring Mount Kits. The TMK-12L is a pre-construction accessory.

Pre-construction refers to framed walls prior to hanging drywall. This accessory

must be used with either the Pre-Construction Mount Kit (PMK-12L) or Wall Mount

Back Box Kit (BB-12L).

The WMKT-12L is a post-construction kit. Post-construction refers to framed walls

with drywall hung. This accessory is designed with a mounting plate so that it can be

placed anywhere on a wall without the support of a stud. The mounting plate is also

ideal for installing the touchpanel in a lectern.

NOTE: If necessary, consult the latest revision of the TPS-12L/15L/17L Operations

Guide (Doc. 6355), TPS-12G/15G/17G-QM-L Operations Guide (Doc. 6356) or the

TPMC-12L Operations Guide (Doc. 6686) for a complete list of mounting options.

These documents are available from the Crestron website

(www.crestron.com/manuals).

Installation Guide – DOC. 6360A Trim Ring Mount Kits: TMK-12L & WMKT-12L •1

Trim Ring Mount Kits Crestron TMK-12L & WMKT-12L

Setup

Supplied Hardware

The TMK-12L consists of a metal trim ring that attaches to the BB-12L or

PMK-12L. The WMKT-12L consists of the trim ring found in the TMK-12L as well

as a mounting plate, and a cutout template set.

The mounting plate provides the necessary support for post-construction

applications. Two overlay cutout templates (4007385) are supplied. One is in the

shape of the required opening; the other is similar to a frame, with the inner area of

the frame the shape of the required opening. Separate the wall cutout templates along

the perforated lines to create the two templates. (Refer to the illustrations on pages 3

and 4.) Use the template that is most convenient.

Supplied Hardware for the TMK-12L and WMKT-12L

DESCRIPTION PART NUMBER QUANTITY

Metal Trim Ring 2013001 1

Metal, Plate, Mounting

(WMKT-12L only) 2012963 1

Overlay, Template, Wall Cutout

(WMKT-12L Only) 4007385 1

The dimensions of the TMK-12L & WMKT-12L are shown below and on the next

page.

Dimensional Drawing – Trim Ring

13.08 in

(33.22 cm)

11.22 in

(28.48 cm)

2.20 in

(5.59 cm)

2 •Trim Ring Mount Kits: TMK-12L & WMKT-12L Installation Guide – DOC. 6360A

Crestron TMK-12L & WMKT-12L Trim Ring Mount Kits

Dimensional Drawing – Mounting Plate

11.99 in

(30.45 cm)

0.06 in

(

15 cm

)

13.63 in

(34.61 cm)

Drywall Cutout Template and Dimensions (supplied with WMKT-12L only), 1 of 2

2 5/16 in

(58 mm) 10 3/4 in

(274 mm)

6 1/4 in

(158 mm)

12 7/8 in

(327 mm)

1 1/16 in

(27 mm)

1/8 in

(3 mm)

11 1/4 in

(286 mm)

11.00 in

(279 mm)

.188 TYP

Installation Guide – DOC. 6360A Trim Ring Mount Kits: TMK-12L & WMKT-12L •3

Trim Ring Mount Kits Crestron TMK-12L & WMKT-12L

Drywall Cutout Template and Dimensions (supplied with WMKT-12L only), 2 of 2

12.00 in

(305 mm)

.188 TYP

1 1/16 in

(27 mm)

11 1/4 in

(286 mm)

11.00 in

(279 mm)

1/8 in

(3 mm)

2 5/16 in

(58 mm)

13 5/8 in

(346 mm) 12 7/8 in

(327 mm) 10 3/4 in

(274 mm)

6 1/4 in

(158 mm)

Installation

This section provides an installation procedure for each Trim Ring Mount Kit. The

“TMK-12L Procedure” starts below and the “WMKT-12L Procedure” starts on page

6. Be sure to review each procedure before starting.

TMK-12L Procedure

This section provides the necessary steps for the assembly of the TMK-12L with

either the BB-12L or PMK-12L. It is assumed that the BB-12L or PMK-12L has

been secured to the stud according to the instructions in the latest revisions of their

Installation Guides (Doc. 6357 and Doc. 6358 respectively). It is also assumed that

drywall is in place and a cutout is made in the drywall along the inside of the

mounting plate for touchpanel installation.

Complete the steps in the order provided. The only tool required and not supplied is

a level.

CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity

above and below the touchpanel for heat dissipation.

NOTE: When installing into the PMK-12L, verify that the 18 AWG bus wire

securing the cables for the touchpanel remains attached.

4 •Trim Ring Mount Kits: TMK-12L & WMKT-12L Installation Guide – DOC. 6360A

Crestron TMK-12L & WMKT-12L Trim Ring Mount Kits

1. Verify that the cutout in the drywall is as clean and level as possible.

2. Insert the symmetrical trim ring into the opening, as shown in the

illustration below.

Insert Trim Ring into Opening

TRIM RING

(2013001)

NOTE: MAKE DRYWALL CUTOUT AS

LEVEL AND CLEAN AS POSSIBLE. THE

TRIM RING ONLY ALLOWS MINOR

ADJUSTMENTS OF THE TOUCHPANEL.

DRYWALL

NOTE: The required PMK-12L or BB-12L is not shown.

3. When the trim ring is in position, bend the top two flanges of the ring

upward and the bottom two flanges downward.

• If mounting into the PMK-12L, bend the flanges approximately 90

degrees.

• If mounting into the BB-12L, bend the flanges back as far as they can

go.

4. Run the necessary cables for the touchpanel and secure them behind the

drywall.

5. The touchpanel can be installed using the eight tapped holes in the

TMK-PMK-15L (or BB-15L). Refer to the latest revision of the

TPS-12L/15L/17L Operations Guide (Doc. 6355),

TPS-12G/15G/17G-QM-L Operations Guide (Doc. 6356) or the TPMC-12L

Operations Guide (Doc. 6686) for touchpanel installation details. Refer also

to the comprehensive illustration shown on the following page.

Installation Guide – DOC. 6360A Trim Ring Mount Kits: TMK-12L & WMKT-12L •5

Trim Ring Mount Kits Crestron TMK-12L & WMKT-12L

TPS-12L Mounting Using the TMK-12L – Exploded View

PMK-12L

TPS-12L

(Bezel Removed)

TRIM RING

(2013001)

DRYWALL

(Bezel)

MOUNTING SCREWS (8)

#06-32 X 1-1/2" (2007254)

NOTE: MOUNTING SCREWS

SUPPLIED WITH TOUCHPANEL.

WMKT-12L Procedure

This section provides the necessary steps for the assembly and installation of the

WMKT-12L into a wall. Review the procedure first, then complete the steps in the

order provided. The only tools or materials required and not supplied are a drywall

saw or equivalent and a level.

CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity

above and below the touchpanel for heat dissipation.

1. Locate an area on the wall that is free of miscellaneous wiring and studs.

2. Make a small hole near the middle of the designated site; verify that the

location is suitable.

NOTE: Make the cutout as level and smooth as possible. The mounting plate allows

for only minor leveling adjustments. If a larger cutout is made accidentally, consider

purchasing the Crestron Mud Mount Kit, MMK-12L. Together with the mounting

plate supplied with the WMKT-12L, it provides a cost-effective means of correction.

Essentially, the combination of these two kits makes up the Crestron Mud Mount Kit

for the wall, WMKM-12L. Simply follow the “WMKM-12L Procedure” in the latest

revision of the Mud Mount Kits Installation Guide (Doc. 6359).

3. Use the drywall saw or equivalent and the provided drywall cutout template

to produce an accurate, clean and level cutout in the drywall.

6 •Trim Ring Mount Kits: TMK-12L & WMKT-12L Installation Guide – DOC. 6360A

Other manuals for TMK-12L

This manual suits for next models

Table of contents

Other Crestron Rack & Stand manuals

Crestron

Crestron BB-1000L User manual

Crestron

Crestron TPS-6X-DSW User manual

Crestron

Crestron CPC-LMT How to use

Crestron

Crestron PMK-3000L User manual

Crestron

Crestron TSW-770-MSMK-ANG User manual

Crestron

Crestron SMK-12 User manual

Crestron

Crestron MMK-4000L User manual

Crestron

Crestron MMK-17L User manual

Crestron

Crestron MMK-3000L User manual

Crestron

Crestron PMK-17L User manual

Crestron

Crestron CAEN-MK User manual

Crestron

Crestron MK-QM-RMCRX User manual

Crestron

Crestron CCS-UC-200-WSTND User manual

Crestron

Crestron TSW-550-BBI User manual

Crestron

Crestron BB-1000L User manual

Crestron

Crestron TMK-6X-DSW User manual

Crestron

Crestron TMK-3000L User manual

Crestron

Crestron TSW-UMB-PMK User manual

Crestron

Crestron TMK-4L User manual

Crestron

Crestron PMK-3100L User manual

Crestron

Crestron TMK-2000L User manual

Crestron

Crestron SSW-MUMK User manual

Crestron

Crestron TSS-752-MSMK User manual

Crestron

Crestron RMK-3100L User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 