Creality CR-10 Series Manual

This guide is for the CR-10 Series of 3D printers. It is also

applicable for the CR-10S/CR-10 S4/CR-10 S5.

Among them, CR-10 mini without T-Bracket (Right) &

Decoration Strip.

Due to the different types of device in the hardware and

software upgrade industry. the products are slightly

different and it is a noemal phenomenon. Subject to actual

product received.

Detailed instructions for use are available on the TF card.

V4.1

CR-10 Series 3D Printer

Guide Book

To be the Chief Evangelist

【To make Top-quality 3D printer】

Notes

1. Do not use the Printer in any other way not described herein in order to avoid personal injury or

property damage.

2. Do not place the Printer near flammables, explosives or heat sources. It is best to place it in a well-

ventilated, low-dust environment.

3. Do not expose the Printer to violent vibration or any unstable environment, because this will cause

poor print quality.

4. The Filaments recommended by the manufacturer are preferred as to avoid clogging in the extrusion

head or Printer damage.

5. Do not use any other power cable except the one supplied. Use a grounded three-prong power

outlet.

6. Do not touch the nozzle or hot bed during printing. Keep hands away from machine while in use to

avoid burns or personal injury.

7. Do not wear gloves or loose clothing when operating the Printer. Preventing the movable parts from

being involved in the squeeze or cutting injury to hunman boday or printer damage.

8. Clean off filament from the nozzle tip with the provided pliers before the nozzle cools. Do not touch

the nozzle directly. This can cause personal injury.

9. Clean the Printer frequently. Usually clean it while power-off, clean the body of the machine with a

dry cloth to remove dust, adhered printing materials and other material of the guide rails. Use glass

cleaner or isopropyl Alcohol to clean the print surface before every print for consistent results.

10. Children under 10 years of age should not use the Printer without supervision.

Preface

Contents

Dear consumers,

Thank you for choosing our products. For the best experience, please read the instructions before

operating the Printer. Our 3D team is always ready to provide you with assistance. Please contact us via

the phone number or e-mail address provided at the end when you encounter any problem with the Printer.

For a better experience in using our product, you may learn how to use the Printer in the following ways:

1. View the accompanied instructions and videos on the SD card.

2. Visit our official website at www.creality3d.cnYou will find relevant software/hardware information,

contact details and operation and maintenance instructions on the website.

1. Introduction....................................1

2. General List ....................................2

3. Device Installion ............................3

4. Cable Connection...........................5

5. Screen Information………………….6

6. Loading Filament ….………………7

7. Bed Leveling ..……...…………………8

8. Software Installation ..………………9

9. For the first Printing…………………....10

10. T r o u b l e s h o o t i n g . . . . . . . . . . . . . . . . . . 1 1

11. After-Sales Services …………………12

1. Display Screen

2. Control Knob

3. Voltage Selection

4. TF Slot and USB Port

5. Nozzle Kit

6. Platform

7. Base Frame

8. Z Gantry Frame

9. Y Stepper

10. Y Limit Switch

11. Z Stepper

12. Z Limit Switch

13. X Stepper

14. Spool Holder

15. Control Box

16. Nozzle Assembly Connection

17. Hot Bed Connection

18. Power Cable Connection

19. Extruder (E) Stepper

20. X Limit Switch

1. Introduction

9 10 11 12 134

35678

Tool List

*CR-10 mini without T-Bracket (Right) &

Decoration Strip.

2.General List

Base Frame Gantry Frame Control Box Tool Kit

No.

Image

Name

Qty

No.

Image

Name

Qty

No.

Image

Name

Qty

Spool Holder & Nuts

M5X25 Bolt

& Lock Washer

sets

Scraper

Spool Holder Bracket

Power Cable

Diagonal Pliers

Sample Filament

(200g)

USB Cable

Hex keys, Wrench

& Screwdriver

TF Card

& Card Reader

Cable Ties

T-Bracket (Right)

PTFE Tubing

(spare part)

Spare Parts

T-Bracket

& Z Limit Switch (Left)

Nozzle Cleaner

Decorative Trim

Install the Gantry Frame

Insert the Teflon pipe into

the quick connector

*CR-10 mini without T-Bracket (right).

M5X25

4pcs

Note: Make sure that the nut

for profile has been turned by

90° before fastening the

T-shaped fixing block.

3.Device Installtion 01

Install the T-shaped fixing block.

◆ Install the Spool Holder and Bracket

◆ Installation decoration

belt

Attach the Bracket with

two thumb screws. Attach Spool Holder

with included Nuts

Finished

Installation decoration belt into

the notch, starting from one end.

Cut off the excess material with

the diagonal pliers

Attach the Decorative Trim to all

parts needing to be decorated.

*Installation decoration belt is available in various colors. The pictures above are for reference only.

*CR-10 mini without Decoration Strip.

3.Device Installtion 02

Extruder (E) Stepper

X Stepper and Limit Switch

Y Stepper and Limit Switch

Z Stepper and Limit Switch

Connect the Stepper Motors according to

the yellow labels on the 6pin (4-wire) side.

Connect the Limit Switches according to

the yellow labels on the 3pin (2-wire) side.



•Select the correct input voltage to match your local

mains (220V or 110V)

•Damage can occur if voltage is set incorrectly.

•Make sure the power cable is connected.

Connect the aviation connectors

to the ports with corresponding

pins

Now your 3D printer is assembled!

4.Cable Connection

Set Temperature of

the Nozzle

Current Temperature

of the Nozzle

Set Temperature of

the Hot Bed

Current Temperature

of the Hot Bed

Part Cooling Fan

Speed

Current Location of

the nozzle

Print Time

Print Progress

Prompt Message

Print Speed

Device Model

Push：OK/Enter Sub Menu

Turn：Change Option/Value

5.Screen Information

1. Preheat

Method 1

Method 2

2.Feeding

Tip：How to Replace the Filament？

1、Cutting filament near the Extruder and slowly feed

new filament until they are fed into the new filament.

2、Preheating the nozzle and withdraw the filament

quickly and feed the new filament.



Press and hold the extruder lever then insert

the1.75mm filament through the small hole of the

extruder. Continue feeding until you see filament

come out the nozzle.

6.Loading Filament

Other manuals for CR-10 Series

Table of contents

Other Creality 3D Printer manuals

Creality

Creality CR-10 Series User manual

Creality

Creality Ender User manual

Creality

Creality CR-200B Pro User manual

Creality

Creality HALOT-LITE CL-89L User manual

Creality

Creality CR-6 SE User manual

Creality

Creality CR20Pro User manual

Creality

Creality Ender-3 S1 User manual

Creality

Creality CR-10 Smart User manual

Creality

Creality HALOT-LITE User manual

Creality

Creality CR-10 Series User manual

Creality

Creality 3D Pad User manual

Creality

Creality CR-10 Max User manual

Creality

Creality CR-10S Pro User manual

Creality

Creality CR-M4 User manual

Creality

Creality CR-10 SE User manual

Creality

Creality Ender-6 User manual

Creality

Creality Ender 3 Pro User manual

Creality

Creality CR-10 S5 Assembly Instructions

Creality

Creality HALOT-MAGE User manual

Creality

Creality Sonic Pad User manual

Creality

Creality 3D Pad User manual

Creality

Creality CR-M4 User manual

Creality

Creality K1 User manual

Creality

Creality 3D Pad User manual

Popular 3D Printer manuals by other brands

Ultimaker

Ultimaker S5 Material Station installation guide

EcubMaker

EcubMaker TOYDIY quick start guide

AnyCubic

AnyCubic Kossel Plus Modification

ReDeTec

ReDeTec ProtoCycler Operation manual

Kywoo3D

Kywoo3D Tycoon IDEX user manual

CraftBot

CraftBot PLUS PRO user guide

3DGence

3DGence INDUSTRY F340 user manual

HP Jet Fusion 4200 Product Documentation Site Preparation Guide

Rokit

Rokit AEP Series user manual

AnkerMake

AnkerMake M5 user manual

DIYElectronics

DIYElectronics PRUSA I3 ELECTRONICS AND SOFTWARE GUIDE

Ackuretta

Ackuretta FreeShape 120 user manual

LONGER

LONGER LK5Pro manual

Stratasys

Stratasys J850 user guide

MakerBot

MakerBot Replicator user manual

Stratasys

Stratasys FDM Vantage Series user guide

ZYYX

ZYYX Pro II user manual

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Startup guide