Contour Opulence User manual

Technical Helpline: 0845 402 9924

Half Height Glass Shower Door

Fitting Instructions

from

Bi-folding door & A return panel

Left hand panel, right hand door illustrated

Bi-folding door & A BI-PARTING DOOR

Left hand panel, right hand door illustrated

TWIN Bi-folding doorS

Not handed illustrated

BI-PARTING doorS

Not handed illustrated

Corner Shower Door Options

FIXED panel

Left hand panel illustrated

TWIN Bi-folding doorS

Not handed illustrated

BI-PARTING doorS

Not handed illustrated

Inline Shower Door Options

PLEASE READ ALL INSTRUCTIONS CAREFULLY & LEAVE WITH THE END USER.

INSTRUCTIONS ARE PREPARED TO HELP WITH THE ASSEMBLY & INSTALLATION OF HALF HEIGHT

SHOWER DOORS TO SUIT A CORNER OR INLINE / ALCOVE SETTING.

CAREFULLY UNPACK THE PRODUCT. ENSURE YOU DO NOT ACCIDENTALLY DISPOSE OF ANY PARTS.

CHECK THAT THE SHOWER AREA / SHOWER TRAY WHERE THE DOORS ARE TO BE

INSTALLED IS LEVEL.

ALL SEALS ARE PRE-APPLIED AND SHOULD NOT BE REMOVED DURING INSTALLATION

PROTECT SHOWER TRAY SURFACES AND COVER ANY WASTES TO PREVENT LOSS OF SMALL

ITEMS & TO PREVENT DEBRIS ENTERING THE PIPEWORK.

USE THE OUTER CARTON TO PROTECT THE FLOOR AND / OR WALL DURING ASSEMBLY IF

NECESSARY.

ALLOW SUITABLE CURING TIME FOR SILICONE SEALANT. THIS COULD BE 24 HOURS DEPENDING

UPON THE VARIETY USED.

IN THE CASE OF ANY DIFFICULTIES BEING ENCOUNTERED, PLEASE DO NOT HESITATE TO CONTACT

OUR TECHNICAL DEPARTMENT ON 0845 402 9924.

DUE TO THE NATURE OF ALL GLASS SHOWER DOORS, WE CANNOT GUARANTEE THEY

ARE 100% WATERTIGHT.

WE DO NOT APPROVE THE USE OF POWER SHOWERS WITH EASY ACCESS SHOWER

DOORS AND SHOWER TRAYS.

Read before installation:

Bi-folding door & A FIXED PANEL

Left hand panel, right hand door illustrated

Revision 1

Contour Showers, Siddorn Street, Winsford, Cheshire CW7 2BA

Telephone: 01606 592586 Fax: 01606 861260

Email: sales@contour-showers.co.uk

Website: www.contour-showers.co.uk

LIFETIME

GUARANTEE

EASY CLEAN GLASS

Opulence glass shower enclosures are coated with an Easy

Clean coating. The coating is an effective protection for easy

to clean glass.

To optimize the durability of the Easy Clean protection, we

recommend the following:

• Regularly rinse off the water & soap deposits by drying

the surface with a squeegee or cloth if necessary.

• Clean the glass panels weekly (depending on the use &

the hardness of the water).

• Clean glass with warm soapy water or water

containg a small amount of washing up liquid.

Rinse thoroughly & wipe with a soft, non-abrasive cloth.

DO NOT USE abrasive products, strong or concentrated

acids, alkalis, chlorine or other abrasive cleaning products

such as household bleach, disinfectant, bathroom limescale

remover / mousse as they may discolour or damage the

coating and void the warranty.

EASY

CLEAN

glass

Before you start the installation, ENSURE that the

shower area / shower tray / wetfloor former area where

the doors are to be fitted is level, both side to side and

front to back, using a spirit level (indicated by the red

dotted lines above).

1: CHECK THE LEVEL!

Run a bead of clear silicone bathroom sealant down the narrow

face, for the full length of the outer compensator and then

screw to the wall using suitable screws (NOT SUPPLIED).

Wipe ANY excess silicone from compensator/wall joint.

FOLLOW THE MANUFACTURERS GUIDELINES WHEN

USING SILICONE SEALANT.

5: LOCATE PANEL “A”

Slide “PANEL A” into the wall compensator. An optional self adhesive

protective strip is supplied for applying to the bottom edge of the glass panel,

see inset above. We recommend using this on a tiled floor setting.

DO NOT DRILL FIXING HOLES INTO COMPENSATOR INNER YET.

DO NOT REMOVE PANEL STICKERS UNTIL DOORS

ARE FULLY ASSEMBLED.

The hinge attached to “PANEL A” will have a spigot ready

to accept “PANEL B”. Ensure the spigot part of the hinge is

on the outer side of the door, with the receiving pin pointing

upwards, to ensure the rise & fall hinges open outward.

6: DOOR HINGE CLOSE UP

•

Mark position of wall compensator

fixing points, checking the

compensator is perfectly vertical.

Drill holes with a suitable drill bit

and insert suitable wall fixings.

(NOT SUPPLIED).

2: COMPENSATOR STYLES

3: POSITION COMPENSATOR 4: FIX COMPENSATOR

Place compensator against the wall ensuring that it rests on the

flat area of the shower tray / wetfloor former.

SHOWER TRAY

COMPENSATOR

•

With the doors assembled and in the

closed position, ENSURE that the

magnetic profiles where the door(s)

/ return panels meet at the corner are

parallel and the magnetic profiles come

together for the full height of the doors.

Offer “PANEL B” to “PANEL A”.

The female hinge section of “PANEL B” locates onto the male hinge

section of “PANEL A”.

9: LOCATE PANEL “C”

Using a spirit level ensure the top of all the door panels are level,

on both the long side and return side, and are also level where

the magnetic profiles meet at the corner.

10: PANELS MUST BE LEVEL!

11: THERE SHOULD BE NO GAPS!

7: LOCATE PANEL “B”

REPEAT STEP 7

Connect “PANEL C” to “PANEL B” as described previously.

You have now assembled one section of your door.

Repeat STEPS 3 to 9 to complete the return panel or inline door

panel assembly. DO NOT TIGHTEN ANY SCREWS YET.

A B C

With the doors still in the closed position, use a 5mm allen key to

fully tighten the 4 x allen screws on each hinge, see above left.

Attach the 4 x chrome cover caps to cover the screw heads.

Using a 3mm allen key tighten the hinges top grubscrew.

This will secure each door panel in position, see above right.

You may find it easiest to do this whilst inside the

shower area.

12: TIGHTEN ALL SCREWS

Connect “PANEL B” to “PANEL A”

With a downward motion, connect “PANEL B” to “PANEL A”,

gently pushing down until the top of the glass panels are level

and the hinge is fully seated in the middle.

DO NOT TIGHTEN HINGE GRUBSCREWS YET.

8: CONNECTING THE HINGE

BI-PARTING DOOR OPTIONS DO NOT USE “PANEL B”. GO TO STEP 9.

“PANEL A”“PANEL B”

A B C

Clip the stabiliser bar on to “PANEL A”

Mark the fixing point on the wall around the wall lug.

Unscrew the wall lug from the stabiliser bar with an allen key and use

it to mark the centre point for the wall fixing. Drill a hole with a suit-

able drill bit and insert suitable wall fixings. (NOT SUPPLIED).

14: 45º STABILISER BAR

Drill the “PANEL A” compensators with a 3mm

drill bit through the pre-drilled 4.5mm hole on the

compensator located on the inside face (inside of

the shower area).

Using the screws supplied in Pack “A” securely fix both

panels to the wall compensators and conceal using the

supplied chrome cover caps .

VIEW FROM INSIDE SHOWER AREA

Take the wall lug from the stabiliser bar and using suitable wall

fixings (NOT SUPPLIED) screw securely to the wall, as shown

above.

Re-attach the stabiliser bar to the wall lug & “PANEL A” as

shown in Step 14.

Silicone joint between floor / shower tray both “PANEL A’s”.

Allow suitable cure time for silicone (this may be 24 hours

depending on the variety used).

FOLLOW THE MANUFACTURERS GUIDELINES WHEN

USING SILICONE SEALANT.

13: DRILL COMPENSATOR

15: FIX STABILISER BAR

Measure from the wall to the front inside edge of PANEL “A”

compensator, see above left. Using your measurement, measure

from the front shoulder of the top cap back to the ribbed area of

the top cap and mark, see above right.

Cut of the excess ribbed area with a small hacksaw.

The cut end of the cap should fit against the wall, see inset above.

16: CUT TOP CAP TO SIZE

Place the bracket of the latch against the leading edge of

PANEL “B” (Next to PANEL “C”). Using a 4mm allen key

tighten the grubscrews, do not overtighten.

OPTIONAL LATCH

17: SEAL WITH SILICONE

TIP: On the outside of the panel silicone along the compensator

and the glass. On the inside silicone along the glass only.

Contour Showers, Siddorn Street, Winsford, Cheshire CW7 2BA

Telephone: 01606 592586 Fax: 01606 861260

Email: sales@contour-showers.co.uk

Website: www.contour-showers.co.uk

built-in independence

You have now assembled one section of your door.

REPEAT STEP FOR THE RETURN PANEL OR INLINE DOOR

Other Contour Bathroom Fixture manuals

Contour

Contour Falcon 30 User manual

Popular Bathroom Fixture manuals by other brands

DURAVIT

DURAVIT C.1 C15240 0090 Instructions for mounting and use

Heatstore

Heatstore HSTRL500WTN Installation and operating instructions

Sunshower

Sunshower PURE SOLO manual

Delabie

Delabie Delabie Sporting 714700 manual

Kohler

Kohler K-13056 Homeowner's guide

ESS

ESS Container TCL-11 installation manual

Mustee

Mustee 22C installation instructions

VITRA

VITRA V-Flow manual

baliv

baliv DUK-80.30 T manual

Malmet

Malmet B105BT Operation, maintenance and installation manual

bathstore

bathstore Transition H1690MM Installation, Care & Adjustment Instructions

BELLOSTA

BELLOSTA Edward 0800/M Installation instruction

baliv

baliv DU-5160 manual

Franke

Franke PRTR0006 Installation and operating instructions

Gessi

Gessi RILIEVO 59011 manual

noken

noken VITAE 100188525-N299998810 manual

Allen + Roth

Allen + Roth 1142VA-30-201 manual

Britex

Britex HBDA installation guide