Concept2 Smoke Screen SANIHAZE User manual

SANIHAZE

VERSION: 09/04/2020

USER MANUAL

Thank you for purchasing the Concept Smoke Screen Sanihaze fog generator. Before using the machine, we

recommend you read the operating instructions carefully. Please follow the safety and maintenance requirements to

ensure a long operating life for your generator.

INSTRUCTIONS AND NOTICES

For any queries, please contact Concept Smoke Screen for further guidance.

• Keep the generator dry.

• Only power the generator from a grounded socket to reduce the risk of electric shock.

• Before powering the generator, ensure that the AC supply voltage matches the voltage speciﬁcations of the

generator e.g. 110V 50Hz or 240V 60Hz.

• When down powering the generator, switch the machine o with it’s onboard power switch before discon-

necting from the mains socket..

• Only re-ﬁll the generator with ﬂuid when it is down powered.

• If the generator will not be used for some time, ensure it is switched o and down powered.

• The generator is for indoor use only. Do not expose the generator to rain or humidity. If the generator

becomes wet, isolate from any power source if safe to do so. Do not attempt to power until it has been

dried. If moisture enters the internal electronic components, isolate from power and contact Concept Smoke

Screen.

• Do not attempt to repair or modify the generator yourself. The internal components contain high voltage

parts that can remain dangerous even after the generator has been disconnected from mains supply.

• Never point the nozzle towards people.

• Do not touch the nozzle as it can become hot.

• Do not cover the generator and maintain a clear area around it of at least 50 cm when it is turned on to

allow sucient air ﬂow to the generator.

• Do not direct the fog towards any naked ﬂames.

• Please observe any warning or caution notices on the generator.

• Use ONLY Concept Smoke Screen certiﬁed ﬂuid with the generator and it must be speciﬁc to the generator.

Non-approved ﬂuid can cause the formation of toxic products and/or damage the generator.

• Do not allow the reservoir to run dry as this can damage the pump.

• Before transporting the generator, please ensure the ﬂuid reservoir is emptied.

• Do not drink or ingest the fog ﬂuid. If the ﬂuid is ingested, seek medical attention.

• Do not allow the ﬂuid to come into contact with eyes. If the ﬂuid comes into contact with eyes, rinse

immediately and seek medical attention.

UNPACKING & INSPECTION

Upon receipt of the generator, carefully open the packing box and check to ensure all parts have been received

and are in good condition. If any parts are damaged or missing, contact Concept Smoke Screen to arrange for

return and inspection.

Sanihaze box contents are as follows:

• 1 x Sanihaze fog generator

• 1 x Mains power cord

• 1 x Wireless transmitter

• 1 x User Manual

SETUP

• Unpack and carefully remove all packing gaskets. Pay particular attention to ensure the nozzle does not

have any packing surrounding it.

• Place the generator on a ﬂat surface with at least 50cm of space around the machine.

• To ﬁll the reservoir, remove the lid and add Concept Smoke Screen approved ﬂuid until the reservoir is 80%

full.

• Replace the lid.

• Do not use unapproved ﬂuid. Doing so may damage the machine and/or result in the production of toxic

substances.

OPERATION

Do not overﬁll the reservoir and remember to re-tighten the cap.

Once the generator has been ﬁlled, power it up by connecting to a mains socket and operating the power

switch on the back. Before powering, conﬁrm that the mains supply matches the voltage speciﬁcation on the

technical notice located on the back of the generator.

Power switch

Fluid level indicator

Mains cable

Wireless

receiver

Fluid tank

INDEX OF TERMS

• Fluid tank - unscrew the lid to reﬁll with ﬂuid

• Fluid level indicator - check the ﬂuid levels

• Power switch - turn the machine on/o

• Mains cable - plugs into a wall socket to give the machine power

• Wireless receiver - allows the machine to be activated remotely usin the wireless transmitter

With the power connected, the generator will begin to heat up. While the generator is heating, it is not capable

of producing fog. During heating, the red LED located on the handle will ﬂash. Once the correct temperature has

been achieved, the LED will turn solid.

LED

WIRELESS TRANSMITTER

Battery: DC 12V 27A battery

Transmitting distance: The nominal range of the transmitter is 50m

without obstacles. Any obstacles between the transmitter and the

generator will reduce the range. In most situations, you should

expect a range of 10-25m.

WIRELESS RECEIVER

Do not try to remove the wireless receiver as this will damage the

main control board of the generator.

ENROLLING ADDITIONAL TRANSMITTERS

The transmitter supplied with the generator has been pre-enrolled at the factory and does not require pairing.

The receiver is capable or enrolling up to 5 additional transmitters. Transmitters may also be enrolled to

multiple generators (enabling one transmitter to trigger several generators simultaneously)

When the generator is ﬁrst powered on, the green LED located near the receiver will ﬂash for 15 seconds

indicating the enrolment period.

During this period, operate button A on the transmitter you wish to enrol.

Successful pairing is indicated by the LED changing to a solid green before the 15 second period has ended.

CREATING FOG

Before creating fog, it is recommended that the area is cleaned as per your standard cleaning schedule. The

fog is able to sanitise in dicult to reach areas, but pre-cleaning is an important step and the fog is intended to

supplement this, not replace it.

There are 2 methods for creating fog once the generator has reached operational temperature.

Wireless transmitter

Pressing button B will activate the generator and button

A will stop it. N.B. if button B was used when enrolling

the transmitter this button will both start and stop the

generator.

Button on handle

Pressing the button on the handle will trigger the

generator for a pre-conﬁgured 5-minute activation.

This can be interrupted by pressing the button again

or using the wireless remote to stop the activation.

The fog produced is safe to breath, however it is

recommended to operate the generator remotely and

leave the area to avoid any possible allergic reaction

to the sanitising fog.

CALCULATING THE AMOUNT OF ACTIVATIONS REQUIRED

The generator creates a sucient concentration of fog at a rate of 20m3/minute.

To calculate the volume of the area that you are interested in sanitising, multiply the length, width and height of

the area. This will give you the volume in m3.

Divide the volume by 20 and this will tell you the number of minutes that one generator will need to produce fog

for.

Example:

100m3 area requires a 5 minute activation of one generator or 2.5 minute activation of 2 generators.

RECOMMENDED LENGTH OF TIME FOR SANITISING.

It is recommended that the fog is allowed to persist in the area for a minimum of 10 minutes before the area is

ventilated.

NOTES:

It is normal for a small amount of condensation to build up at the nozzle. When the generator is cool, simply wipe

this down with a clean cloth.

It is normal for the generator to emit a small amount of fog from time to time when it is in standby. This can also

occur after the generator has been down powered and is cooling down.

If the generator is operated for an extended period of fog production, eventually it will go under the ready tem-

perature and will need to pause in order to reheat – this is done automatically. The red LED on the handle will

ﬂash during this period and will return to solid once the generator has reached its operational temperature.

If the generator runs out of sucient ﬂuid, it will automatically stop until it is re-ﬁlled.

CLEANING AND STORING YOUR SANIHAZE GENERATOR

Do not allow the ﬂuid reservoir or container to become contaminated with impurities. Immediately replace the

caps once ﬁlling has been completed.

When cool, the exterior of the generator may be wiped with a clean damp (but not wet) cloth.

Before storing the fog generator, empty the reservoir of ﬂuid and replace with distilled water. Run a 2 minute

cycle with distilled water to avoid any blockages occurring while the generator is in storage.

It is recommended to power up the generator and run a distilled water cycle at least once a month if it is not

being used.

Excessive dust or liquid residue on the generator will reduce it’s performance and cause poor heat dissipation

so it’s important to keep the case clean..

Concept Smoke Screen Limited

North End Business Park, Station Rd, Swineshead, Lincolnshire, PE20 3PW United Kingdom

Tel: +44 (0) 1205 821111 | Fax : +44 (0) 1205 820316 | [email protected].uk | www.smoke-screen.com

SANIHAZE (08/04/2020)

Table of contents

Other Concept2 Fog Machine manuals

Concept2

Concept2 E+ Series Setup guide

Concept2

Concept2 Air Trace MK2 User manual

Popular Fog Machine manuals by other brands

Antari

Antari ICE Product guide

Boost

Boost BOOST-FOG400LED-BK instruction manual

Home Accents Holiday

Home Accents Holiday FM1000-ASH user manual

EuroLite

EuroLite ZEITGEIST FOG-1200 user manual

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Operation and maintenance manual

PROEL

PROEL DRAGO HEAVY PLFD150HY manual

Sparklyn

Sparklyn Y846 user manual

Magicfx

Magicfx CO2 Gun manual

Ibiza

Ibiza LSM500LAS instruction manual

Antari

Antari M-5 user manual

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER user manual

High End

High End F-100 user guide

Chauvet

Chauvet ARENA 2100 FLEX user manual

Antari

Antari X FAZER user manual

Beamz

Beamz F1600 instruction manual

Sagitter

Sagitter SG ARS900C user manual

KISANKRAFT

KISANKRAFT KK-STF-480 user manual

Orion

Orion OT-U250PP Installation and use manual